安全购物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全购物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Coming Soon: Studio Equipment

首页  Coming Soon  

Studio Equipment

Options
Items 1 to 17 of 17 on page 1 of 1
FORTHCOMING
AniModule Quad Comparator Module
AniModule Quad Comparator Module (CV modulation / logic / comparater / utility / quad synth module)
Cat: 794399 Rel: 31 Dec 20
 
Quad comparator module
Notes: Simple quad comparator based around the LM339.

It will take your Voltages and turn them into Logic On.

When your signal is higher than the threshold the Gate goes high and the NOT Gate goes low.
When your signal is lower than the threshold the NOT gate goes high and the Gate goes low.

You can set the threshold anywhere from about -10V to +10V.

Input 1 is buffered then normalled to JackSwitches 2->4. So you could send an LFO in to Input 1, set different thresholds for all the inputs and have all the gates/NOT Gates fire at different points from the same LFO.

115 mA +12V
95 mA -12V
29 mm deep
O 5.00 (1 Votes) Average Rating
Read more
MRP:$190.29 SAVE 17%
coming soon $158.57
FORTHCOMING
AniModule V9a Module
AniModule V9a Module (clock generator / sequencer / waveshaper synth module)
Cat: 793809 Rel: 31 Dec 20
 
VC sequencer & waveshaper module
Notes: Here's a powerful animal to add to your sequencing arsenal.

Send your CV to the CV In. As the Voltage increases the sequence steps forward. As the voltage decreases the sequence steps back.
Scale and adjust your input voltage to taste with the Onboard Attenuator and Offset.

Control the Output CV with an individual Potentiometer for each step.

When a step changes, a 10MS trigger is sent to it's corresponding switch. If the latching switch is depressed it allows the trigger to pass to the Trigger Out.

There is a switch per step for slew (portamento/slide).
and a Potentiometer to control the Slew Amount.
There is also an input to allow gated control of when the slew turns on and off which will work in conjunction with the switches.

This module is looking for 0V to +5V. The Offset is 0V to +5V.

To allow for chaining of the V9a and rests, 0V will put you under the sequencer range and +5V will put you over the sequencer range.
When the sequence drops below step 1 or over step 9, 0V will be sent to the CV Out and No Trigger will be sent to the Trig Out.
When step 1 or 9 is activated a trigger will be sent to the Trig buss.

Max Current Draw:
+12V = 40mA
-12V = 11mA

Width: 14HP Depth: 39mm
Read more
MRP:$304.73 SAVE 17%
coming soon $253.94
FORTHCOMING
AniModule M1xXOR Module
AniModule M1xXOR Module (mixer / sequencer / switch synth module)
Cat: 793792 Rel: 31 Dec 20
 
CV sequencer module
Notes: The Animodule M1xXOR is the Jon Snow of Animodule's product lineup. Described as a "bastard progeny" and "unholy union" by its creators, the module is an amalgamation of the V9a, VCSS, XXX_OR, and MixMan modules. Each of the module's channels, as well as the mixer, can be used independently of the sequencer, enabling a variety of self-contained and inter-module uses. When used independently for self-contained functionality, the module can function as a 4-channel DC-coupled mixer or as 4 individual channels of gated attenuation.

How It Works:
-Signal goes in to Channel Input (it's DC connected so you can use Audio OR CV).
-Signal is attenuated via Channel Attenuator.
-Signal is allowed to pass through to Individual Channel Output AND Mixer Output IF Gate Input is High OR Switch is depressed.

Sequencer:
-Clock Pulse High in to Clock Input Moves Sequence forward 1 Step.
-The Channel that the step is On will be open
-CV can be used to control the Sequencer via the CV Input.
-There is a resolution of 5 steps (4 channels and a 0 step allowing for all channels to be cleared from the Sequencer).
-There is an attenuator and offset to help properly scale and position your CV Input.
-CV Input is expecting 0V to +5V, but with the Attenuator and Offset will easily work with -/+5V.
-Clock and CV maybe used in tandem resulting in some mind melting rhythms!
-In that case the Clock will step forward 1 step from it's current position (unless it's on step 4 in which case it will roll over to step 1)
-The Clock used in conjunction with the CV will bitshift the sequence to the left, incrementing the static position of the step counter by 1 (wrapping around to step 1 after step 4).
-Fer' Instance, 2 Clock counts and CV is on 0. Step will be on Channel 2
-Gate High in to Reset will reset Clock counter to step 1 OR if Clock Input is being used in conjunction with the CV Input the reset will clear the Clock Counter and return the step to where the CV indicates it should be without any BitShifting

*Gate Input / Switches in conjunction with Sequencer:
-The Sequencer and the Gate Input / Switches combine in a XOR gate. If one is High and the other is not, that channel will be open. If BOTH are High, that channel will be closed.

Despite the lengthy description, the M1xXOR is very intuitive (and unbelievably Fun!) to use.
Each Channel (and the Mixer) May be used independently of the Sequencer.
So if you're not in the mood for Rhythmic Insanity You still have a gateable 4 Channel DC-Coupled Mixer AND/OR 4 independent and gateable channels of Attenuation.
You will NEVER just have it filling space in your cabinet.
You will find a use for it in EVERY patch!

All this in 8HP with a depth of 33mm (from rear of Front Panel).
Read more
MRP:$243.52 SAVE 17%
coming soon $202.92
FORTHCOMING
AniModule XXX_OR Module
AniModule XXX_OR Module (clock modulator / CV modulation / logic / ring modulator synth module)
Cat: 794039 Rel: 31 Dec 20
 
XOR module with analogue & digital outputs
Notes: A Triple Analog XOR module with an Analog and a Digital (Gate) Output.

You can use the Gate Output for your normal Boolean XOR functions (feel free to input Analog signals.)

But the real magic happens at the Analog Output.

-Take 2 waveforms and feed 1 to A and 1 to B
-When 1 signal is low the other is normal
-When 1 signal is high the other is inverted

It's not just on and off like a digital XOR- you get all the varied nuances of a tri, sine or saw wave that you put in to it.

-The Analog Output of Channel 1 is normalled to Channel 2 A Input via the jack switch
-The Analog Output of Channel 1 is normalled to Channel 3 A Input

This way you can still use your Analog Out from each channel and not worry about patching the next XOR function in the chain together.

Use it for CV!
Use it for Clocking, Tempos and Rhythm manipulation!
Most of all Feed your Audio into it!

Width = 4HP Depth = 29mm

Current draw is:
+12V = +33 mA
-12V = -21 mA
Read more
MRP:$133.07 SAVE 17%
coming soon $110.89
FORTHCOMING
AniModule AnVilope Module
AniModule AnVilope Module (clock generator / envelope generator / LFO synth module)
Cat: 794381 Rel: 31 Dec 20
 
Envelope generator module
Notes: A Simple, Affordable, 4HP, Analog Envelope Generator.

Attack, Decay, Release... Simple.

- Envelope Out 0V to +7V
- Loop function so you can use it as a Variable Wave-Shape LFO / Timer
- Inverted out that goes from +7V to 0V

Function:
When the gate is High the envelope will rise and cycle through it's phases.
When gate goes low again the envelope will revert to the release phase.

If the Gate is longer than the ADR phases, the decay will play out then go to release and the envelope will end after the release.

Sprinkle them all over your system!

4HP Depth : 28mm
Read more
MRP:$114.44 SAVE 17%
coming soon $95.36
FORTHCOMING
AniModule DD Dual VCA Module
AniModule DD Dual VCA Module (CV modulation / panning / VCA / dual stereo synth module)
Cat: 794391 Rel: 31 Dec 20
 
Dual VCA module
Notes: A Dual VCA for Audio or CV.

Mod In 1 is Buffered, Inverted then Normalled to Mod In 2, to facilitate stereo panning and VC CrossFading without a bunch of support modules.

Don't want it? Just turn the attenuator down or plug a signal of your choosing in to the Mod In 2.

Current Draw: +12V = 25mA, -12V = -22mA

8HP, 28mm Deep
Read more
MRP:$204.93 SAVE 17%
coming soon $170.77
FORTHCOMING
AniModule Lil' Monster VCO Module
AniModule Lil' Monster VCO Module (oscillator synth module)
Cat: 794393 Rel: 31 Dec 20
 
VCO module
Notes: At 8HP and 28mm deep this is A Frightening little Oscillator with Monstrous PWM, Sick, Sick Sync, and Terrifying FM capabilities!!

Great 1V/Oct tracking

Range from below to above the audible

All Waveforms respond to your Sync Input signal

Current Draw: +12V = 21mA, -12V = -21mA 8HP, 29mm Deep
Read more
MRP:$248.84 SAVE 17%
coming soon $207.36
FORTHCOMING
AniModule MixMan Module
AniModule MixMan Module (attenuater / mixer/ multiple / polariser / utility synth module)
Cat: 794394 Rel: 31 Dec 20
 
Mixer multiple & CV manipulator module
Notes: This quintessential module, while seeming fairly utilitarian, is practically Indispensable.

At only 8HP wide and 30mm deep
You can Mix, Mult, Invert and Offset your Audio and CV.

For starters there is a 3 Channel Mixer with x3 Buffered Outs.
Then there is a dedicated Analog Inverter.
Last but not least there is an Offset Manipulator.

The Offset Manipulator is designed to take a signal and combine it with an offset.
It will work fine without a signal coming in to it though. Just take the signal from the Offset Manipulator out and dial in your desired voltage.

The Offset Manipulator Out is Normalled to the 3rd Mix In Jack Switch. If you don't want your Mixer Signals Offset, Connect a plug to the 3rd Mix In Jack First, or just dial down the 3rd attenuator to 0.

The Mixer Out is Normalled to the Inverter In Jack Switch. That way you can have an inverted version of your MixOut at the Inverter Out without using an extra patch cable
Read more
MRP:$131.74 SAVE 17%
coming soon $109.77
FORTHCOMING
AniModule LogicOgic Module
AniModule LogicOgic Module (clock modulater / frequency divider / logic synth module)
Cat: 794401 Rel: 31 Dec 20
 
Logic module
Notes: This is a handy module. It's nice to have a few ORs and ANDs around when you're fiddling around with your clocks and percussives.

The Output from FlipFlop1 Q is normalled to the FlipFlop2 Input via the jack switch.

The NOT Q outs from the FlipFlops are fun to stagger your clock pulses or use as a Sub-Oscillator. The Inverter/Buffer can be sent to a Gate-Trigger converter and back to the OR to double your clock.

2 - FlipFlops (Q and NOT Q outs for each)

2 - OR Gates

2 - AND Gates

1 - Buffer/Inverter

All the outs are Buffered.

55 mA +12V
38 mm deep
O 4.00 (2 Votes) Average Rating
Read more
MRP:$262.15 SAVE 17%
coming soon $218.45
FORTHCOMING
AniModule SOB v1 Module
AniModule SOB v1 Module (state variable filter & waveshaper synth module)
Cat: 794397 Rel: 31 Dec 20
 
State variable filter module
Notes:  A State Variable Filter with an adjustable WaveFolder on the input.

Self-Oscillating Filter Tracks 1V/Oct

Vactrol Input allows you to control CutOff via gates/triggers without using up an EG

Pot to mix "Clean" and "Folded" signal levels

Filter and/or Fold Audio Or Control Voltages

2 Input Signal mixer

1 Input Control Voltage Mixer

1 Input to Vactrol for CV Modulation

1V/Oct In

current Draw: +12V = 31mA -12V = 34mA
Read more
MRP:$234.20 SAVE 17%
coming soon $195.16
FORTHCOMING
AniModule TrAniModule Module
AniModule TrAniModule Module (distortion / mixer / utility synth module)
Cat: 794385 Rel: 31 Dec 20
 
Transistor amplifier module
Notes: Behold the TrAniModule- A 1 Watt, Class A Transistor Amplifier in an 8HP, 29mm deep Package.

With a Line Input to jack your iPod or your Walkman up to synth levels.

You want to process your Line Level signal before you send it roaring out the belly of this little beast?

The Line out is normalled to the Mixer, so just plug in and it'll rip your signal away from the maws of this monster.

If you're looking for high fidelity, you better just slink back in to your studio with your Grandaddy's precious pretty monitors...

If you want portability and a warm sound that will drive when you crank it all the way, without knocking your granny off her chamber pot, We got'em both! AniModule has been working hard to help you achieve your Brown Note!

The Mix out is just a nice clean, buffered mix of your 2 Attenuatable Inputs and the Line Input.

The Speaker Out is normalled to the speaker in case you want to drive a bigger cab, or plug your pretty little headphones in, or capture the tone after the amplifier. If you plug in, the speaker cuts out, but the master will still control the volume- proving to be very handy for live performance.

...and really, if you want a nice clean sound, just dial back the levels a little bit!
Read more
MRP:$175.65 SAVE 17%
coming soon $146.36
FORTHCOMING
AniModule ShNoiZe Module
AniModule ShNoiZe Module (noise / random / sample & hold synth module)
Cat: 794389 Rel: 31 Dec 20
 
Sample & hold module
Notes: This is your classic Sample and Hold.

Signal goes in - trip the threshold on the Pulse In - and the out will "hold" the voltage at the point when you triggered it.

There is a separate White Noise circuit. It is normalled to the S+H Input for all your random needs. There is also a Noise out so you can access it independently as well.

There is a slew knob so you can smooth and lag your output to taste

Current Draw: +12V = 23mA, -12V = -12mA

4HP, 29mm Deep
Read more
MRP:$131.74 SAVE 17%
coming soon $109.77
FORTHCOMING
AniModule TikTok Module
AniModule TikTok Module (clock modulator synth module)
Cat: 793800 Rel: 31 Dec 20
 
Clock divider & multiplier module
Notes: The TikTok is a 4HP Clock Divider/Multiplier.
It has Divisions and Multiplications of:
*//2
*//3
*//4
*//5
*//6

There is a Clk Input and a Reset Input.
Both are buffered with an opamp based comparator circuit.
They are looking for approximately +1.1V on a rising edge.
This means that you are not constrained to gate (pulse) signals to trigger them.

The Reset input resets your divisions clock counter to 1

There is a switch to select Mathematical or Musical divisions.

The Multiplication Outputs 25MS Trigger pulses.
The Division Outputs are on as long as your Clock source.

Avg Current draw:
40 mA
-9 mA
Peak Current Draw:
80 mA
-17 mA

Width = 4HP
Depth = 38mm
Read more
MRP:$195.61 SAVE 17%
coming soon $163.00
FORTHCOMING
AniModule Line_Amp Module
AniModule Line_Amp Module (multiple / preamp / utility / dual stereo / external synth module)
Cat: 793793 Rel: 31 Dec 20
 
Buffered multiple module
Notes: Check out AniModule's Line to Synth Level Converter.

2 Channels of 1 in <--> 2 Out.

Each channel is designed to multiply your input by *3 to boost your Line Gear / Tablet / Phone so you can integrate audio OR Control Voltages from your auxiliary systems.

Each channel's input is designed with Line Level gear's input impedance in mind.

Perfectly compatible with Synth Output Impedances, but the standard Synth Input Impedance is higher than Line level equipment is expecting.

Don't need to amplify your XPhone right this minute? Never fear! Just Hit the Switch!

This module won't sit unused in your cabinet breeding resentment and dust bunnies.

Hit the switch and that channel becomes a normal 2 HP Unity Gain Buffered Mult.

Only need one channel of each? It's YOUR Choice!
Read more
MRP:$110.45 SAVE 17%
coming soon $92.03
FORTHCOMING
AniModule STD Syncopated Timing Disruptor Module
AniModule STD Syncopated Timing Disruptor Module (clock generator / clock modulator / logic synth module)
Cat: 793790 Rel: 31 Dec 20
 
Syncopated timing disruptor module
Notes: The STD, or Syncopated Timing Disrupter is a dual tap tempo clock with CV control for clock division and multiplication. If one wishes to synchronize the STD with other clocked gear, there is also a Gate input. The CV inputs can shift the clock to being upto 8x faster or /8 to be slower. This function is voltage controllable to turn the STD into a nonstop groove machine. Included in this are three logic functions that output gates depending on how the two channels are interacting. There is OR, ADD, and XOR logic functions.

2 Independent Tap Tempo Clock Channels
Prefer to use a Gate? No Prob! Just Patch in to the Gate Input.

Use the Div/Mult/Offset Pot to Multiply or Divide your Clock Time up to *8 - /8

Or patch In to the CV Input to Modulate the Mathematical Madness!
When CV is being input the Div/Mult/Offset Pot behaves as an Offset.

CV Input wants 0V to +5V, but whatever you got, Between the Offset, and the Front Panel CV Attenuators, it's easy to dial in your desired range of "On the Fly" Mathematical Clock Time Modulations.

Want to sync the 2nd channel to the first?
Latch the Ch1 - Ch2 switch and the Output of Channel 1 is normalled to the jack Switch of Channel 2.
You can still control the Multiplications / Divisions of each channel Independently!

If that wasn't enough to get you poppin' penicillin prophylactically there's more!

The bottom row of jacks constantly output OR, AND, and XOR Logic Combinations of the 2 channels combined!

Want to use something funky (like a Sine Wave / Envelope / Random Voltage Generator) to set the rhythm? The Input is a Buffered Comparator set to trigger at any signal above +1.2V

Perfectly happy up in to the Mid- Audio range.

6HP
+44mA
-16mA
Read more
MRP:$219.57 SAVE 17%
coming soon $182.96
FORTHCOMING
AniModule MIDI_Gate Module
AniModule MIDI_Gate Module (MIDI synth module)
Cat: 793791 Rel: 31 Dec 20
 
MIDI gate interface module
Notes: The AniModule MIDI_Gate is an easy way to integrate your MIDI-synced workflow with your Modular Synth.

10 Gate Outs that correspond to MIDI notes C1 - A1 (36 - 46).

MIDI NoteOn >> Gate is High

MIDI NoteOff >> Gate is Low

Programmed to receive on MIDI Channel 10

All this in 4HP!!!

Use it to send Multiple Clocks synced to your main Clock.

Use it to trigger events to effect samples piped in via a Line_Amp or TrAniModule in realtime in the analog domain for Live Performance or Resample.

Use it to interface in realtime with your Keyboard, Pad Based Controller, or DAW.

Width = 4HP

Depth = 33mm
Read more
MRP:$207.59 SAVE 17%
coming soon $172.98
FORTHCOMING
AniModule Gate_Mod Module
AniModule Gate_Mod Module (clock modulator / dual stereo / frequency divider synth module)
Cat: 793797 Rel: 31 Dec 20
 
Gate modifier & trigger delay module
Notes: Got a gate that's gonna make you late? Run it through the Gate_Mod! Got a trigger comin' sooner than you figger'd? Run it through the Gate_Mod!!

Let's face it, couldn't we ALL use a little more length?

This Tiny (yet powerful) Module allows you to manipulate your gate length and delay your event triggers with ease and minimal impact on your HP.

Take an incoming Signal above ~1.1V (OpAmp Comparators on the Inputs make very forgiving Clock Inputs) and shrink it down to 5MS or lengthen it up to 5 Seconds.

That Gate will appear at the Gate Out.

When the Gate is Over a 10MS Trigger will turn on at the Delay Out.

Set the length of the Gate with the Time Potentiometer OR with the CV Input.

The switches allow you to choose between Interrupt OR Dividing Behavior (1 for each channel).

If you have Interrupt selected, when Clock In receives a new Clock Pulse the time will reset, essentially lengthening your Gate Out and Delay Out to the Time you have set + the time that has already elapsed.

So Gate will never go Low and Delay will never go High if you have a Time set longer than the interval between Clock Pulses (Useful if you have staggered, irregular or random Clocks).

When Dividing is selected Clock In will Ignore new Clock Pulses until it has finished the current cycle it's running.

The Delay 1 Out is Normalled via the Jack switch of the Clock 2 Input for all kinds of Timing madness!

Width = 4 HP
Depth = 37mm
Current Draw:
+12V = 35mA
-12V = -18mA

*The Gate_Mod firmware has been updated as of Mid August 2015. There was a bug in the Delay Out section that prevented it from resting at full 0V. All Gate-Mods shipped After the Firmware was updated include the new revision.
Read more
MRP:$195.61 SAVE 17%
coming soon $163.00
Items 1 to 17 of 17 on page 1 of 1

Filter

Coming Soon: Studio Equipment
Close