Synth modules

Notes: The ZONE B.F. module is an element of the Capsule TITAN. Zone basses frequences stands for low frequency zone. This module is composed of 2 LFOs, both LFOs have 16 sync-able waveforms.

Speed : speed of the LFO, range from 0.1 Hz to +/-200 Hz
Wave (LFO 1 & 2) : 16 Syncable waveforms

The ZONE B.F. (black edition onwards) now features an additional mode. On the back of the PCB you will find two jumpers, marked as JP1. CV1 is LFO channel 1 and CV2 is LFO channel 2. By moving the jumper so it sits on one leg (rather than 2 as when you have received the module), the Sync input for either LFO channel now becomes LFO speed input, controllable via CV.

Tech Specs

- SYNC 1 & 2 : LFO waveform is reset when an impulse signal is received
- OUT 1 & 2 : LFO signal outputs 1 & 2
- Voltage swing is -/+5V
- LEDs display LFO activity
- Eurorack 5 HP
- Metal pot, panel mounted, screwed
- Consumption: +12V 40mA, -12V 10mA

Notes: 'Beast's Chalkboard' is dual channel stepped voltage source and adder for your eurorack modular synthesizer system. It primarily is intended as a dual octave switcher for VCO's but has many other uses including sequence transposition, FM ratio creation, buffered CV distribution and VCO calibration.

Technical Specifications:

Supply: +/-12V (Reverse voltage & polyfuse protection)
Current Draw: ~30ma
Size: 6 HP
Depth: 22mm (including power header)
Offset Error: +/- 10mV

Notes: Introducing the SD808, part of our new series of drum modules that brings analog percussion to the modular synth world, instantly turning your system into a self-contained music machine.

The SD808 is the TR-808's analog snare drum circuit adapted for use in Eurorack modular synthesizer format and was designed to sound like a fresh-out-of-the-box, 1980s TR-808 snare. Adapting the circuit to the modular format has allowed us to add special features like independent accent levels, a high-powered gain stage, a dual-input pulse-shaper, and an adjustable noise source - all without compromising the signature sound of the TR-808 snare drum.

The SD808 sounds tight and extremely snappy because it's analog - the real thing, not samples. The sound is made with three analog sound generators mixed together: two oscillating sine waves and a noise source. The SD808's front panel controls have a lot of sweet spots with sounds that are not just limited to snare drum sounds; it can also create other electronic percussive elements.

The noise source generator in the original TR-808 machines were revised in later production batches, resulting in variations in sound across the production run. The SD808 uses this later, revised circuit to create a snare drum hit that is slightly darker, has more body, and is more realistic. Just like other drums in this series, the SD808 includes a high-powered output gain stage capable of producing signals up to 20Vpp, allowing you to get an array of harmonized snare drums sounds with even tighter attacks. On the inputs, we have designed a dual-input pulse-shaper circuit so you can trigger the SD808 with Trigger/Gate signals from step sequencers, clock dividers, or any other pulse/clock sources. This eliminates the need to shape pulses sent to the module and ensures the same stable sound at peak power, regardless of your pulse source. All these unique features make integrating this legendary sound generator into your modular synth easy, unleashing the power of real analog drums.

Notes: The CP909 is the TR-909 clap sound analog generator in Eurorack format. This is yet another low-cost analog drum generator from a legendary drum machine in your modular synthesizer, expanding your Tiptop Audio modular drum machine even further.

The CP909 is an exact reproduction of the original analog circuit and, with the addition of just one extra knob, "trashing" the frequency of the internal noise generator, we have added greatly to the spectrum of sounds that can be generated - all that without compromising the signature sound of the TR-909 clap.

The CP909 clap effect is made by a special triple-saw envelope generator that controls the gain of a VCA. The sound source feeding into the VCA is made by a quasi-random logic based noise generator; some might call it "digital noise" though this term might be misleading in today's world of microcontrollers and sound samples. What really makes the noise generator is a ring of logic gates, so primitive, so BO's, and that's the sound of the 909 Clap!

The CP909 includes a high-powered output gain stage capable of producing hot signals. On the inputs, we have designed a pulse-shaper circuit so you can trigger the CP909 with trigger/gate signals from step sequencers, clock dividers, or any other pulse/clock sources. This eliminates the need to shape pulses sent to the module and ensures the same stable sound at peak power, regardless of your pulse source. Based on the architecture of the 909, the Accent input is versatile and able to take in both CV and Gate signals for continuously changing dynamics. All these unique features make integrating this legendary sound generator into your modular synth easy, unleashing the power of real analog drums.

Notes: This is the version II of the original uVCA.

This module was adapted from a design by David G. Dixon

Notes: The 8S is an 8 step sequencer in 8 HP with control over some parameters of the sequence as reset, hold, random step and direction. The inputs have been designed to work with clock related signals like triggers or gates but any type of CV signal can be used. The output signal path is completely analog and its range can be set to unipolar (0 to +5 volts) or bipolar (-5 to +5 volts) via jumper on the back of the module.

Technical specifications:

8HP

38 mm depth

Consumption: +12V: 25mA ; -12V: 5mA

Notes: Strom+ is a strong, reliable and safe 4HP power solution for your modular system. The Strom+ power module includes many safety mechanisms to prevent your modules from being damaged. These include most importantly short-circuit protection, overvoltage protection and a replaceable main input fuse. See the full list below.

Strom+ also offers a current sensing technology that indicates current consumption of your system. LEDs of each rail will turn orange then red, when current consumption reaches or crosses the maximum load of that rail.

Strom+ has extremely low ripple, even under full load. This means better sound and stability for your modules.

One module can power multiple skiffs via Strom Passive Module, a Strom Connector Cable, or a KOMA Strom Busboard.

Technical Specifications

Inputs and Outputs

Output: 1.5A @ +12V | 1.5A @ +5V | 1.0 A @ -12V
Input: 15V, 4.6 A (center positive)

Safety Mechanisms

Replaceable input fuse. Protects the wall-plugged adapter. The KOMA Strom AC/DC adapter actually has its own protection mechanisms and will itself shutdown in most cases before the input fuse trips.
Input overvoltage. Strom+ works up to specification from 15V - 20V input and works out of specification up to 28V input.
Input reverse polarity protection
Output overvoltage protection
Output short-circuit protection
Output over current protection
Output undervoltage protection
All above output protections independent for each rail. If any rail fails, the whole module shuts down.
Connectors and Controls

Main DC-Input (15 VDC)

On/Off switch
Front panel connector to a passive Strom module
2 standard Eurorack 16-pin connectors (for modules or a flying busboard)
Back panel Strom connector to solid busboards

Dimensions

4HP
48mm without Eurorack power connector connected (distribute power via Strom connector cable)
52mm with Eurorack power cable connected

Notes: Taking equal inspiration from gritty delays on cheap mixers, the sounds of dub and the fracturing of consciousness in time and space, the Coma Reactor looks like a deceptively simple delay module... till you start digging deeper.

The Coma Reactor boasts the crunchy sounds of the PT2399 chip, but adds a number of useful routing possibilities that really open it up for sound mangling that transcends the norm.

Independent volume controls for dry, wet as well as FX loop return allow you to blend in clean, delayed and affected sounds to suit your needs. A CV input on the module increases or decreases the delay time, going from slight tape-echo warbles to some truly seasick pitch shifting. A buffered clean through allows you to pass an unaffected unity gain to a mixer or other device.

The Send/Return path allows you to process your delay signal through another effects unit. Without anything plugged in, a truly nasty bandpass filter lurks in the delay feedback path. The 2022 edition of Coma Reactor features Frequency (CV controllable) and Resonance knobs for this filter.

Lastly, this completely delirious module is also capable of generating noises and oscillating with no input attached, making it a useful soundtrack generator for the end of the world.

The 2022 Coma Reactor includes a breakout header for future integration with upcoming AFA expander modules.

Power consumption: 39mA at +12 V and 21mA at -12 V
Depth: 22mm
HP : 12

Notes: Unlock the potential of the Quad LFO with the LFO Phase Expander. Each expander gives you three outputs that duplicate the LFO with a fixed phase difference. The first ranges from 0- to 180-, the second from 90- to 270-, and the last from 180- to 360-. Along with the original output, this gives you four phases of modulation. These are easily tuneable to quadrature (all knobs centred), but also any arbitrary phase relationship. You can attach up to four expanders, one for each LFO, giving you up to sixteen modulation sources.

A multiphase LFO is extremely useful for building rhythmic modulations, particularly when paired with analogue logic, such as provided by Babel. Further, regardless of the waveform selected on the Quad LFO, the output of the Phase Expander is always a sine wave. This gives you the useful possibility of having three rhythmically related phases of an LFO synced to a clock signal.

Other than rhythmic modulations, the most common use of a multiphase sine LFO is in creating panning and crossfade controls that sound correct using only one or more VCAs. This is useful in panning sounds back and forth, rotating a sound in quadraphonic space, creating Shepard tones, etc.

Even when you don't have a specific need for exact phase relationships, a multiphase LFO gives you a convenient way to expand your palette of potential modulators, adding three related but distinct waves.

Specs

Size: 6HP
Depth: 22mm
Power Consumption: +12V 21mA, -12V 21mA
Output Swing: -5V - +5V peak
Output Impedance: 1kO
Output Drive: 2kO (min), 20kO+ (ideal)

Notes: QMS does quadraphonic mid-side processing. Given a left front, right front, left back, and right back signal, it produces a mid and three side signals: left-right, front-back, and cross or diagonal. Then given these latter signals, it again produces left front, right front, left back, and right back. It has intelligent normals for passthrough, -6dB lowered mid and side signals to avoid clipping, and is equally useful for stereo mid-side when quadraphonic is not available.

Rather than merely creating an image of a sound, something that you passively look at, this module allows you to create a sonic texture that fills a room. Listening becomes active exploration instead of passive observation. Ambient music is all about space. But stereo can only provide a passive experience of this space. It's like there was a wonderful landscape glimpsed from a train window, and many experiments in stereo imaging attempt to reproduce the experience of being in that train, looking through that window. With quadrophonic sonic textures, you get to leave the train and run with the caribou.

Specs

Size: 6HP
Depth: 22mm
Power Consumption: +12V 75mA, -12V 75mA
Output Swing: -10V-+10V peak
Input Range: -10V-+10V peak
Input Impedance: 94kO
Output Impedance: 150O
Output Drive: 600O (min), 2kO+ (ideal)

Notes: Babel is a tool for creating massive intermodulation, and a workhorse for analogue logic, depending on your use and interpretation of its function. It provides three inputs, which can be arbitrarily increased with the chainable expander (see below). For each of those inputs, Babel outputs the maximum value (ANY), the minimum value (ALL), and the balanced middle value (XSOME), which follows along the centre values of the input waves. What CENTER means is adjustable via knob and CV control. XSOME is particularly interesting, as it has the same general shape as a multiplication function, but with sharper edges. What this means it that Babel will create ring-mod like intermodulation-but with extra harmonics like those produced with a wavefolder, and with an arbitrary number of inputs, instead of just two.

When viewed as a logic module, Babel takes any group of truth values and tells you whether any of them are true (ANY, the equivalent of "or" with just two values), whether all of them are true (ALL, the equivalent of "and" with just two values), and whether some, but not all of them are true (XSOME, the equivalent of "xor" with just two values). Turn CENTER all the way to the right for 0-+5V logic, or leave it cantered for -5V-+5V logic-handy when your "logic" modules are really LFOs.

Specs

Size: 6HP
Depth: 22mm
Power Consumption: +12V 44mA -12V 44mA
Output Swing: -10V-+10V peak
Input Range: -10V-+10V peak
Input Impedance: 30kO
Output Impedance: 150O
Output Drive: 2kO (min), 20kO+ (ideal)

Notes: The New Systems Instruments VCA module gives you four well-calibrated VCAs in 6HP. These VCAs use operational transconductance amplifiers (OTAs) at their core, for true linear operation. However, unlike most OTA VCAs, the New Systems VCA is extremely low noise and distortion, coming in at < 0.2%, with ~0.05% typical.

There's no such thing as "transparent," particularly in synthesis, where the concept of an original signal that could be faithfully reproduced is often altogether absent. In a VCA in particular, a desirable envelope response can be even more important than accurate reproduction of the input at some fixed level.

The New Systems Instruments VCA has an extremely neutral, open sound. The envelope response sounds noticeably fast and accurate. If you want a dirtier VCA, stay tuned. New Systems are in the process of designing a different VCA with some control over signal and envelope linearity.

Specs

Size: 6HP
Depth: 22mm
Power Consumption: +12V 25mA / -12V 25mA
THD+N at 1kHz: 0.2% (max), ~0.05% (typical)
Output Swing: -10V - +10V peak
Input Range: -10V - +10V peak
CV Unity: 5V
Input Impedance: 85kO
Output Impedance: 150O
Output Drive: 2kO (min), 20kO+ (ideal)

Notes: Pico EF is Erica Synths' take on envelope follower module in 3hp! Pico EF features a preamp with +40dB gain (enough to boost even guitar and dynamic microphone signals for use in a modular system), envelope output with adjustable attack time and a gate output with adjustable threshold. The Pico EF can be used as a preamp, overdrive unit or for controlling VCFs with audio signal, or to use with external instruments to control your modular system in other creative and experimental applications.

Technical specifications:

Preamp boost: up to +40dB
Audio output level: 10Vptp
Envelope output level: 0 - +10V
Gate level: +5V
Power consumption: 25mA, -15mA
Module width: 3HP
Module depth: 35mm

Notes: Incredible sounding VCO module that helps you get incredibly rich signals out of your synthesizer. The Dreadbox Hysteria VCO features a huge frequency range of 16hZ to 32kHz. This gives you a lot of functional pitch to work with, allowing you to explore the sounds capable from this module.

The sounds themselves rest on a variable waveform selector - meaning you can scroll through the waveforms and blend them together. This can even be CV controlled, so you can obtain an evolving sound that changes over time. The modules in the Chromatic series give you a great starting point in the world of modular synths and are a must-have for beginners and professionals alike.

Power Consumption: 114mA @ +12V , 46mA @ -12V
10HP
35 mm deep

Notes: Mix up to four stereo channels in just 4hp, or chain multiple modules together to add channels. Inputs are normalled for mono operation. Simple, compact and high quality at a reasonable price.

Supplier's Notes:
4xSt.Mixer is 4 HP quad stereo mixer.

Right inputs are normalled to Left inputs for easy mono operation

Several 4xSt.Mixers can be chained together or with other HN stereo modules via sockets on the back side

65 mA +12V
50 mA -12V
35 mm deep

Notes: The Beautifier is a flexible OTA based filter, featuring a lowpass/bandpass switch and a selectable slope of 24db and 12dB. Two attenuated CV inputs for frequency cut-off and resonance. The filter self-oscillates at a given point and can be driven quite hard if you crank up the gain. All in all, a versatile analogue workhorse with a lot of character; from smooth and creamy to quite raw and screamy.

47 mA +12V
19 mA -12V
0 mA 5V
26 mm deep

Notes: Sindikat is made to be placed in the heart of every modular setup: copy, invert, attenuate, scale, get different polarity versions simultaneously of two pair of mixes, mix CV as well as audio (up to 8 sources in total), mute or switch to add desired source to a bigger unity mix, scale two separate mixes with chosen gain.. All circuits can preserve their independent use and/or be combined!

Details & use:

The module consists of circuits designed to group the most useful operations for signal mingling in modular synth setups -but in the more fun manner!

It is designed in the way that the circuits can function independently -be patched to the other modules- or to be combined inside the module at the same time!

On the top of the module there is a buffered multiple (the bi-color led is indicating signal input and its polarity) : Next to the input there are two outputs giving the exact copy of the incoming signal. On the third output you'll get the 'attenuverted" version of that signal which is controllable by the dedicated attenuator/inverter potentiometer.

This signal can be further added (or muted) via its switch, internally to a unity gain mixer situated on the bottom of the module via its SUMM OUT.

This mixer has its own 3 inputs who will accept CVs as well as audio signals with an output gain of 1/3.

Its bi-color led will indicate the polarity of the incoming signals.

In the center of the module there is a CV Processor consisting of two mixers each mixing two signals- in the way that:
The first one takes two signals (A and B) and outputs simultaneously the positive version of their mix (AB+ OUT) and the negative version (AB- OUT).
Their gain is scaled by the potentiometer: going on 1x in the middle position to 2x fully turned. (After middle position with a stronger signal and due to higher gain it will start to saturate producing an distortion-like effect)
Further, via their switch, those mixes also can be added to a unity gain mix (SUMM OUT) and therefore creating a larger mix.
You'll do that by choosing which polarity output you want to send to a summing mix.
In the middle position of the switch the signal is "off" so you can use this to mute/un-mute the signal in the unity mix. Also, even if it is in "off" position this only breaks the internal link to a unity mix but you can still use their distinctive outputs to send your positive and negative mixes elsewhere in your system.

Goes the same for the second one: C and D inputs giving positive (CD+) output result and negative (CD-) simultaneously , all with gain select and the switch choice for summ positive or negative (or none) to a bigger unity mix.

You can also choose to use those two circuits as a simple attenuators for ex. by patching only one signal so you'll get an attenuator and polarizer at once!

The module can process CV and audio as well in every circuit.

Therefore, by summing eventually all the signals to a final "SUMM OUT" output you can create up to 8 sources -in the module- large mix!

Made for more fun with a modular!

This module fits perfectly well with Modulaire Maritime "Decca" switch-based manual control module.

As these modules are developed from practicing recording in "one take" (same for a live performing), combining them you get an extended control over CVs, gates and audio going on in the system, allowing to switch- stop/mute, change polarity, introduce/mix more gates, drums,.. on the fly.

8hp
25mm deep
Reverse voltage protected

Notes: Dual xFade is a compact voltage controlled crossfader suitable for both audio and CVs. Smaller knobs set manual crossfade between A<>B, and bigger knobs are CV attenuverters. LEDs show the adjusted positive and negative CV sides for easy monitoring.

Upper inputs (section 1) are normalled to lower inputs (section 2). Thus the same signal pair A&B can be differently crossfaded in both sections.

The switch clones section's 1 controls to the section 2, which is useful to make stereo Dry/Wet adjustment or stereo VCA.

This module can be used as:

two independent crossfades

two independent VCAs

stereo crossfade or Dry/Wet control

stereo VCA

panner

Four jumpers on the back can give optional 5x amplification for each A or B input. Sot it is easy to crossfade modular level with linear level from pedals. Installed jumpers give 1x amplification, removing jumpers gives 5x amplification.

Output 1 is mixed with output 2 if left unconnected.

Notes: The ‘Pip Slope’ (rev II) is a compact envelope and function generator. It supports both Attack/Decay and Attack/Sustain/Decay type envelopes with both direct and voltage control of Attack and Decay times. Envelope shapes can be morphed between exponential, linear and logarithmic type slopes. Envelopes can be made to loop, repeating infinitely or decreasing with time or amplitude for echo and bouncing ball type effects. An ‘End of Cycle’ trigger output further extends the envelopes functionality for both clocking and burst or fill type effects.

The improved Pip Slope adds a number of new features and updates over the original Pip whilst keeping the same size. Improvements include increased output resolution, finer control of fast envelopes, a new morphing shape control, switchable 5v or 8v maximum envelope level, additional loop modes and an additional trigger output.

Features:
Compact envelope and function generator in 4HP.
Trigger and gate inputs.
Voltage and direct control of attack and release times.
Snappy or super long envelope times – ranging approx 1ms to 7 minutes per stage.
Optional self looping ability with 3 different loop modes: Decreasing amplitude, decreasing time, and regular loop.
Shape control that morphs the envelope shape from logarithmic to linear to exponential curves.
End of Slope trigger output that fires a trigger at the end the envelope or loop cycle.
Selectable 5v or 8v max envelope level output.
Reverse polarity protection.
Skiff friendly.
Designed and Made in the UK.

Technical Specifications
Supply: +12V 30mA / -12V 10mA
Size: 4HP
Depth: 38mm

Notes: The SVF is a 4hp 2 pole 12dB State Variable Filter Eurorack Module available as a Eurorack DIY Kit, PCB and Panel, or Built Module.

It provides Low Pass, Band Pass, and High Pass outs inspired by WASP and Thomas Henry filter topologies. The filter has 2 audio inputs, but channel 2 is jumper selectable between standard audio in or Ping-able operation. The 2019 revision also adds improved cutoff and resonance response and attenuversion through the ACV IN using the above pot. CV IN provides another unattenuated voltage input to modulate the frequency.

At the CV in, +10v will open the filter completely if the cutoff pot is CCW(counter clockwise). With the cutoff knob at noon the filter can be opened with +5v or closed with -5v. CV input at the ACV in is dependent on the CV attenuverter knob.

There are also several jumper selectable modes for max resonance, self oscillation or no oscillation based on the setting of the resonance pot. According to the jumper configuration, the filter is capable of clinical and clean, to juicy and drippy, to low pass gate sounding plonks, to screaming chaotic resonance. When set to self oscillation mode, the filter can produce a sine like wave with no input and a trapezoid like wave in the max resonance jumper setting. In max resonance mode, the filter output can exceed 10Vpp. On the newest version, there is a trimmer on the top pcb to set the lowest cutoff frequency.

The new black and white pcb/panel is reversible meaning, one side is classic (first picture) and the other side is soulless (second picture).

Notes: The Fold Processor is a voltage-controlled wave multiplier and sub-octave generator. The circuit is based on a classic diode design that adds odd harmonics by folding the incoming signal, followed by subdivided square waves.

The wave folder creates new waveforms from standard sine, triangle, sawtooth, and square waves and includes a CV input with an attenuator, making it very easy to create beautifully animated folding sounds. Adjustable voltage-controlled Inject alters the bias point creating an even wider palette of sounds.

The subdivide generator squares the fold output generating 4 more sounds spaced one octave apart, each with its own gain knob and mixed to the Subdivide output jack. Mixing the four can create anything from discordant square wave swarms to sweet harmonic oscillator stacks, from a stable square version of the folded wave to freaky PLL-like glitched slides.

Overall results can sound evil at times and sweet at others, a true multi-faced devil.

Size: 12HP
Depth: 31mm
Power: +12V 60ma / -12V 55ma

Notes: All channels support headphones with 16 - 600 Ohm impendances.

Superb sound with low distortion and great low end.

Linkable channels (B to A and C to A).

All inputs with multiples, ie feeding different mixer channels.

Mono input is normalized to stereo.

Protected with relais, assuring soft starts and DC protection for your headphones (> +/- 10V input)

Width: 12 HP

Notes: FONT is a massive sounding liquid filter- designed to bring you powerful basslines, tons of FM modulation and a clean resonance over your audio path.

It features two simultaneous outputs:
2-pole Low Pass
2-pole Band Pass

It can also work as a sine oscillator, tracking 1V/OCT when the resonance is at its maximum level.

FONT can be used to make basslines, acid patterns thanks to its organic and musically sounding resonance.

Ping it to produce percussion sounds such as, bongos, congas or toms.

Applying a pitch envelope, it really shines as a kick-drum machine!

22 mA +12V
25 mA -12V
0 mA 5V
15 mm deep
O 4.60 (10 Votes) Average Rating

Notes: This module is a 8 ins and 8 outs precision buffered matrix.

Every output has a rotary switch to select an input. You can make the same input go through several outputs but not several inputs go to the same output.

There's also a bicolor led next to every switch for visual info of the signal that is going thru it.

Allows fast patch changes and easy rerouting signals, both audio and cv.

Can be used as a traditional buffered multiple, pretty flexible one: 1 x 8 outs, 2 x 4 outs, 4 x 2 outs or any other combination.

62 mA +12V
65 mA -12V

Notes: Nice dual-module gate/envelope generator which can run off any audio signal. Feed it drums, synths, samples or a mic input and and generate CV modulation signals.

Supplier's Notes:
The Percussion Interface (PI) and PI Expander are a pair of Eurorack modules that generate gates and envelopes from acoustic drums, samplers, drum machines, and virtually any audio source.

Converting microphone, instrument, line and modular signals into CV and clock/gate signals, the PI and PI Expander are suited for synchronizing sequencers or other modules to the rhythm of an audio track or live percussion. The modules can simultaneously be used as a pre-amp for microphones or line-level signals, while generating inverted envelopes useful for side-chaining. The PI module contains all the core functionality and can be used without the Expander to conserve space. The Expander requires the main PI modules and adds three gain stage options, a modular-level audio output jack, a 1/4" (6.35mm) input jack, and envelope attenuation capabilities. The two modules are only sold together, they are not available separately.

Electrical and Mechanical Specifications:
Module size (PI):
4 HP Eurorack formal module
0.98" (25mm) maximum depth with power cable
10-pin Eurorack power header

Module size (PI EXP):
4 HP Eurorack formal module
0.98" (25mm) maximum depth with power cable
8-pin cable connects to PI

Power consumption:
with PI Expander
+12V: 104mA
-12V: 65mA
without PI Expander
+12V: 69mA
-12V: 56mA

Audio Inputs:
1/8" [3.5mm] on PI main module, and 1/4" [6.35mm] on PI Expander
100k input impedance, AC-coupled

Audio Outputs:
Voltage range: -10.4V to +10.8V, DC-coupled
1k output impedance
Gain Characteristics
Gain range: < -100dB to +54dB (500x)
Clip light turns blue when signal (post-gain) exceeds 2.5Vpp
Gate is triggered when signal (post-gain) exceeds 6.3Vpp
Clip light flashes red when signal clips on Audio Out jack (exceeds +10.8V)
Gate Out Jack
1k output impedance
+8V gate/trigger signal
6ms - 0.5s pulse width
+ Env Out jack (jack on PI main module)
1k output impedance
+9V peak (sustain), -60mV resting (off)
15ms attack time
70ms - 6s exponential decay time (1% of peak voltage)
- Env Out Jack (jack on PI main module)
1k output impedance
+9V resting (off), -150mV peak (sustain)
15ms attack time
70ms - 6s exponential decay time (1% of peak voltage)
Env. Out jack (attenuated jack on PI Expander)
1k to 26k variable output impedance
+9V maximum
-60mV minimum
Inv. Out jack (attenuated jack on PI Expander)
1k to 26k variable output impedance
+9V maximum
-150mV minimum
Included with the PI+EXP:
8-to-16 pin power cable
8-to-8 pin cable for connecting to the Expander
M3 Knurlie screws (4)

Notes: MMF is an analogue, multimode filter with a 12dB per octave slope. Its sonic character swings all the way from classic low pass to squelchy acid lines. Simultaneous outputs of low pass, high pass, and band pass filter types are provided allowing for many variations of the input signal. Whether you're looking for smooth and creamy, or resonant and wild, MMF can go there.

Notes: Play is a high-fidelity sample player with a full feature set.

Up to 32 samples can be loaded at a time and dynamically switched between using the file knob and associated CV input. Playback modes include one-shot, looping, or gated playback; all with extremely low latency. Transform your samples by pitching them up two octaves or down three octaves, all with a pitch knob that can be free running or quantized to semitones. The pitch CV input tracks volt per octave across its entire range and allows for musical sequencing of samples. Play ships with a pre-loaded SD card packed with loops, drum hits, and field recordings to get you up and running immediately.

Notes: VCA 3X is a simple yet great solution for synth users looking to add more VCAs to their setup in a single and compact module. This module features 3 VCAs with individual Signal and CV inputs and outputs.

Notes: 4-input VCA stereo mixer w/ pan, stereo out, metering

50mm deep

Notes: This small utility is the pedal's lover best friend, it allows 2 diferent chains of pedals to be independently connected to your synth.

The Send channels attenuate the synth level to instrument level.

The Return channels amplify the signal from instrument to synth level.

Specs:
- Width: 4 HP
- Depth: 3 cm
- Max current: 10mA

Notes: Inspired and officially licensed from Teia's Stochastic Function Generator which was introduced in 2013 but is no longer available. This earlier version served as an inspiration, but with a completely rebuilt and reprogrammed mcu to a fully featured 4 voice 2 stage envelope and slew generator.

ADDAC System ADDAC506B VC Stochastic Function Generator Expansion Module (black faceplateADDAC System ADDAC506B VC Stochastic Function Generator Expansion Module (black faceplate
This expansion allows extra I/O to the ADDAC506, namelly:

Four trigger inputs for the random engine.

Four CV random outputs from the random engine.

Notes: 3xVCA offers three high class amplifier circuits with linear characteristic. Thanks to AC / DC compatibility, a very low noise floor and basically no distortion, the module is not only a great partner for control voltages, but audio material as well. Besides a signal input and output, each VCA has its own CV input. The dual potentiometers regulate levels and bipolar CV attenuation values of all amplifiers. Using these rather unusual, yet very practical components, it was possible to equip the 3x VCA with a front panel that is only 6 HP wide. Switches allow the user to feed the results of one amplifier to the output of the next amplifier, so we can get 1+2, 2+3, and 1+2+3 outputs mix. Two-colored LEDs visualize CV and output signals.

60 mA +12V
60 mA -12V
35 mm Depth

Notes: The Octave Fuzz is SynthRotek's take on the classic 70's SuperFuzz circuit, made into a Eurorack module, which has improved on some aspects of the original as well, including an increased output.

Two distinct voices like the original: switchable between scooped midrange and massive midrange bump.

Aggressive: It will sound massive and in-your-face like no other circuit can. This is for sonic explorers and heavy music only. In short, it's not useful for EVERYTHING, but the things it DOES do it excels at. Sounds especially killer for keyboard and bass sounds.

Tuned to give a subtle distorted waveform one octave up via wavefolding (see the video to view this on an oscilloscope). (Completed modules come pre-tuned; there are calibration instructions at the end of the assembly instructions for the kits)

This circuit has been optimized for Eurorack. You can find a guitar pedal version here.

Current Draw:
32mA @ +12v
24mA @ -12v
0mA @ +5v

Notes: The Hungry Robot Sample & Hold provides basic S&H functionality with some added bells and whistles. It uses an internal clock dialed into a very useful range. If the internal clock rate is not to your liking, you can bypass the Rate knob by patching a clock signal into Clk In. The Sample & Hold has a built in attenuverter giving a bit of added control over the random voltages that are outputted. White noise out for uses elsewhere. Traditionally a S&H samples voltages from chaotic white noise, but E.In allows you to bypass the white noise and patch in your own sample source (i.e. patching an LFO in for a bit crushed LFO). As with all Hungry Robot "Modular Boxes" the Sample & Hold can be powered with a simple 9V DC, Negative Center power supply.

KNOBS
-MINUS/PLUS: Attenuverter for output. Allows you to sweep between positive and negative voltage outputs.
-RATE: On board clock source ranging from approximately 25ms to 1000ms.

PATCH POINTS
-E.IN: Bypasses internal white noise as a sample source. Patch in any CV source that you want to sample from
-STATIC: Taps into white noise output (0-5V range)
-CLK IN: Bypasses internal clock with your provided external clock
-S&H OUT: Two buffered outputs of S&H voltage

Dimensions: 4.7" x 2.6" x 1.5"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: Lovely little mono filter module in a compact desktop format. Based on the classic Prophet 5 filter, ideal for processing synths and signals, hooking up to Eurorack or other Hungry Robot modules.

Supplier's Notes:

The Hungry Robot VCF is an all analog, 4-pole low pass filter with a self-oscillating resonance control. It is a close replication of the filter circuit found on the famous Prophet 5. It uses a HM2040 which is a high quality, faithful replication of the original SSM2040 chip. This resonant filter has a beautiful tonal quality. The over-sized knobs provide a satisfying tactile response. The cutoff frequency can be controlled by external control voltage. It has a built-in attenuator and invert switch for the incoming CV. CV input does not track at 1V/Oct, but is scaled to act as a VCA when a 5V signal is applied to CV input. As with all Hungry Robot "Modular Boxes" the VCF can be powered by a simple 9V DC, Negative Center power supply.

KNOBS
-FREQUENCY: Sweeps the cutoff frequency of the filter.
-CV: Attenuator for incoming CV input.
-RESONANCE: Sets resonance of filter. Small volume drop is to be expected. Will self-oscillate at higher settings.

SWITCHES
-INVERT: Inverts the incoming CV input. Toggle to the right to invert incoming CV

PATCH POINTS
-IN: Patch Audio Signal In
-CV: CV input for Frequency. Allows for CV control of this parameter.
-OUT: Patch Audio Signal Out

Dimensions: 4.7" x 2.6" x 1.5"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: Designed with and for performing artists, Switch 4 delivers a hands-on signal switching and routing solution for your Eurorack modular synthesiser.

Quickly mute audio signals, trigger envelopes live, select modulation sources on the fly... With custom dual-action toggle switches, an intuitive interface and sturdy construction, Switch 4 will prove just as useful on stage as in the studio.

The bottom switching section includes four lever-actuated toggle switches, to make or break the signal path between the inputs and outputs. These switches feature a dual action: latched upwards, momentary downwards.

The four input signals are also sent to the top routing section, where two rotary switches allow you to select the signals to be sent to the matching outputs. Here you'll also find dual-action toggle switches, for added versatility.

Finally, all signal paths are buffered, avoiding signal cuts when shorting a jack during patching or severe loading effects when driving many inputs. The high-end components provide exceptionally low noise and distortion, so Switch 4 can reliably process audio, control voltages and gates/triggers.

Notes: By combining a mixer and four VCAs in a single module, Mix 3 manages to provide a unique combination of compact size and functionality in just 6 HP. High-end signal paths ensure extremely low noise and distortion, wide headroom and precise gain control, despite the small form factor.

Each of the three main channels has an exponential response, which is more natural for audio than linear, as it matches the human hearing. However, all signal paths are DC-coupled, so control voltage (CV) signals can be processed as well.

What truly sets Mix 3 apart from other compact mixing modules are the three CV inputs, providing voltage control over the signal levels. This even allows you to go beyond unity gain and reach up to +20 dB of amplification. Once a CV input is used, the corresponding channel knob becomes a CV attenuator.

When clipping, Mix 3 does so in a clean, symmetrical way. This yields a very pure overdriven sound, only containing odd harmonics, and allows the module to be used as a triple voltage controlled distortion.

Additional features include audio indicator LEDs, a fourth auxiliary input, voltage control over the output level and a line output jumper setting.

Notes: Loop is a high fidelity looper with four unique recording modes and an intuitive user interface. It can capture up to five minutes of audio with reverse, and half-speed playback accessible. Each recording can use one of four modes: Sound on Sound, Dub, Replace, and Infinite (i.e. Frippertronics). Whether you're looking for minimal part layering, or full blown ambient soundscapes, Loop will take your patch for a ride.

High fidelity audio - 24-bit, 48kHz with five minutes of recording time
Four recording modes: Sound on sound, Dub, Replace, and Frippertronics
Intuitive interface
Half speed and reverse playback

Tech Specs:
Width: 2HP
Depth: 42mm

Notes: Focused versatility seems an oxymoron when describing the features that led us to design the Mixwitch.

With only a pinch of mixing, inverting and controlled switching, we brew up a plethora of combinations and uses.

This is voltage processing magic!
The Mixwitch design comes from a frustration with attenuvertors (bipolar attenuators-inverters) whose off (neutral) position is difficult to retrieve, especially in live situations.

We went for a digitally-controlled analog path where polarity inversion would be at the touch of a button. So, the usefulness of attenuating/inverting can be realized by turning the pot down, swiftly pressing the inversion button and reopening the level. The zero level is where you expect it, with the pot full down.

Once we had a clean polarity control, we easily added a mute function offering the benefit of pre- adjusted pot settings ready to be activated at will.

The next step was to bring something extra, useful and creative. There are plenty of analog switches controlled by a clock; but arbitrarily selecting an input with a voltage is less known. Having both control capabilities combined with our specific mixer features creates a unique fusion: welcome to the Mixwitch !

Notes: Clever four-channel utility module designed to make it easier to achieve perfect oscillator tracking and transpose CV signals. Also includes some neat quantising and portamento features.

Supplier notes:
The CalTrans solves issues encountered when playing tonal music with a modular system: tracking problems, curves unrelated to Volt per octave ratio, limited octave range, cumbersome transpose, ...

The CalTrans corrects and expands the range of troublesome VCOs and brings V/Oct tracking to anything that oscillates.

Besides calibration, the CalTrans offers live play features. Each channel can be quantized and any combination of them transposed jointly.

A pair of rotary encoders with detent allow an precise selection of octaves and semitones.

VCOs whose tracking doesn't go high enough to follow the leader will see their pitch repositioned in their highest possible octave so that the global harmony is unaffected.

You can add a pinch of portamento and glissando to each channel and save the whole in user presets.

Notes: A four channel mixer, suitable for audio or control signals. It features regular and inverted outputs as well as an LED level meter.

Specifications:
Current needs: +12V: 21mA, -12V: 10mA
Width: 5 HP
Depth: 20mm (including power connector)
Aluminiun, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: Each of the two sections of the module is capable of performing the analog multiplication of two signals (A and B) and add an offset (C). It can also act as a dual voltage controlled attenuverter, dual ring modulator, dual VCA or four channel mixer (see block diagram below).

The B inputs are routed to an attenuverter that multiplies the signal between -2 to 2, while the offset inputs (C) route through a unity gain attenuverter (multiplies the signal between -1 and 1).

The output of first section is routed to the output of the second (when the first's output is unused), so the second output can act as master to achieve (A1*B1+C1) + (A2*B2+C2) or (A1 + C1) + (A2 + C2) - a 4 channel mixer.

The through-zero (four-quadrant) multipliers in the A*B+C allow for true Ring Modulation. To achieve this, simply connect two waveforms to the A and B inputs.

Notes: A compact attenuverting (attenuator-inverter) joystick controller and Gate Generator. With it, you can generate and process two control voltages using only one hand. Provided controls for CV ranges and offset adjust the boundaries of your control, this way it never gets out of the desired range, ensuring sensibility and playability even with wild performance gestures.

Specifications

Current needs: +12V: 25mA, -12V: 10mA
Width: 12 HP
Depth: 35mm (including power connector)
Aluminium, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: The 333 is a summing and distribution module for Eurorack modular systems.

It is composed of three identical sections, the red, yellow and green, each of those featuring three inputs summing amplifier with three independently buffered outputs.

Derived directly from the CGM creative mixer series, the sum section is DC coupled, allowing the sum of control voltages as well as audio signals.

With an extremely low tolerance in both sum and output sections, it is suitable also for summing quantized voltages like the ones coming out from the quantized outputs of the SAPEL.

In case CVs or audio signals are particularly hot, the 6dB attenuator might be helpful to reduce exactly by 50% the incoming signals.

Red and yellow output are also normalled to the 1st jack socket of the yellow and green input: in this way this module can also work as a 1 to 9 buffered multiple.

Notes: Hat is a hi-hat cymbal with a wild side. Finding something unique is easy with a blend of sounds ranging from robotic to metallic. At its core are three unique sound sources made up of six oscillators, a noise generator, and a number of filters. Sizzle affects each source independently, adjusting oscillator and filter frequencies, allowing for a broad range of sounds. In addition, separate trigger inputs for open and closed allow for a complete hi-hat pattern on a single module. No matter what situation it's in, Hat provides shimmering, metallic timbres for any percussive purpose.

Notes: ADSR is a four stage linear envelope with two expressive ranges. Each stage can be modified independently allowing for the creation of complex, multi-segment envelopes. Great for modulating filters, VCAs, and oscillators.

Notes: Arp is a gate-driven arpeggiator with a multitude of chord types and playback modes. Voltage control over both root note and chord type allow for sequencing any combination of chords in any key imaginable.

With the rate of the arpeggio and reset capability in your own hands, you're free to create dynamic rhythmic melodies from your favourite chords. Take your tonality for a ride with Arp.

Notes: Div is a 2 channel, voltage controlled clock divider and multiplier. Incoming clock signals can be multiplied or divided by a factor of 16 with a multitude of values in between.

CV inputs provide external control of the current clock rate, allowing for the creation of dynamic rhythms from a single clock signal.

Notes: Mix is a 4 channel mixer that is great for audio or control voltage signals. Up to four inputs can be combined to a single output each with its own level control.

Notes: Verb is a lush stereo reverb with a full feature set and superior audio quality. A wide range of reverb times take your sound from small room to never-ending concert hall.

CV over mix allows dynamic movement between the dry and reverberated sound, and the dampening control lets you dial in the perfect timbre for the wet signal. Whether you need a traditional reverb for an FX send or an esoteric sound design tool, Verb can take you there. Get lost in space with Verb.