Synth modules

Notes: The Rene music synthesizer module is a powerful three-dimensional prism of composition. It is the world's only 3D Cartesian Music Sequencer. Named for the French philosopher & mathematician Rene Descartes, it uses the Cartesian coordinate system to unlock the analogue step sequencer from the shackles of linearity. The original Rene was a one-channel, two-dimensional Cartesian sequencer with limited memory, this new Rene is a three-channel, three-dimensional Cartesian sequencer with memory for up to 64 complete States. Considering the multiple channels and FUN programming options per multiple axis, Rene has become an n-dimensional matrix or tesseract of synthesizer sequencing.

Notes: The Falistri is a fully analogue multi-purpose movement manager designed to generate and edit voltages to easily accomplish any patch.

The module can be divided into two big parts: in the upper two-thirds of the panel take place two specular function generators, while the lower third is composed of a dual cascaded frequency divider, a linear slew limiter, and a four-quadrant multiplier.

Key features:

Two Function Generators: Envelopes, LFOs, Oscillators
Adjust the Shape Without Changing the Time
Exclusive Shapes per Stage
Trig Buttons: Play Those Envelopes!
Three Play Modes (Voltage-Selectable)
Interacting Functions: Quadrature Mode
All the Outputs, Everywhere
Cascaded Frequency Dividers
Four-Quadrant Multiplier
Linear Slew Limiter

Size 18 HP
Depth 38 mm

Current draw
170 mA @ +12 V
170 mA @ -12 V

Notes: The only module named after a Swedish botanist? Possibly. Relentless synth innovator Dave Rossum pushes the boundaries again with a state-variable stereo filter offering through-zero frequency modulation. Sounds complicated. Sounds good.

Supplier notes:
Following in the tradition of Evolution and Morpheus, LINNAEUS represents yet another Dave Rossum innovation in filter technology.

LINNAEUS is a stereo state-variable filter that provides the unique ability to linearly modulate its resonant frequency through zero into negative frequency, while maintaining stability. With extensive voltage control of nearly every parameter, Linnaeus lets you manipulate the filter's natural response curve in new ways, to create both subtle and dramatic timbral effects. And with a "one-knob-per-parameter" interface, LINNAEUS inspires sonic creativity that invites (and rewards) real-time interaction.

LINNAEUS's cutoff/resonant frequency is exponentially voltage controllable from sub-audio to ultrasonic frequencies, while its resonant gain (Q) is exponentially voltage controllable from 0dB to greater than 60dB.

LINNAEUS's channel output response characteristics are independently and continuously variable from Lowpass, through Bandpass, Highpass and Notch, to Low and High Shelving characteristics. Voltage control of the response characteristics are independently selectable for each of the two channels.

The linear thru-zero modulation is provided by an integrated modulation oscillator and/or an External Linear FM modulation input.

The voltage-controllable modulation oscillator can track the filter's exponential frequency or operate independently. The modulation oscillator's output waveform is continuously variable from Off through Sine, Triangle, and Sawtooth, to Square. The modulation oscillator output is summed with the external linear FM input and applied to the modulation index VCA, which controls the linear thru-zero modulation index from zero to 8X. The modulation index is, of course, also voltage controllable.

Notes: Freaky stereo digital delay from the Eurorack gods at Make Noise. Typically creative stuff, packed full of interesting features for creating complex echoes, modulating sounds and generating loops.

Supplier notes:
The Mimeophon music synthesiser module is a stereo, multi-zone colour audio repeater by Make Noise and soundhack, coded by Tom Erbe.

The Mimeophon (from Greek mimeo (repeat/copy) and phon (sound)) is a modern take on various historical sound copying, echo and repeating devices. It allows for Stereo modulations of Time, Space and Timbre of Mono or Stereo sound sources. The Mimeophon is capable of modulating and morphing time scales of repeated sound from micro-sound to note to phrase length while also colouring and spatializing the repeats.

Notes: Eight channels of audio and CV sampling with real-time editing and processing. Does basic sampling well but quickly gets creative and weird.

Supplier's notes:
The 'Squid Salmpler' is a Eurorack 8 channel audio & CV sampler. It is designed for immediate real time sampling, editing and mangling within a modular context.

Taking influence from early hardware samplers, The Squid Salmple focuses on usability and instinctive operation, incorporating a proven Pamela's Workout style user interface for minimal screen dependence and a fun, hands on experience.

With support for sampling and playback for both audio and CV, as well as CV control of all parameters, on-the-fly bank loading and saving to USB, The Squid Salmple brings a unique take on old school sampling into the modular realm.

The Squid Salmple comes with a USB Stick containing approximately 90 banks of original carefully curated royalty free samples. This includes a wide range of sounds from classic drum machines and weird synths to field recordings and CV modulations. Banks are provided by both ALM and some of our favourite artists and friends including Mumdance, Solid Blake, Russell Haswell, Lauren Flax, Dave Burraston (NYZ), Sue Zuki, Dungeon Acid, Sasha Lewis and Andrew Duff.

Notes: The VCA Matrix from 4ms is a playable 4x4 matrix of 16 VCAs.

Four CV or audio inputs can be routed in any amount/combination to four outputs, using the 16 CV control jacks, Level knobs, and Mute buttons.

Notes: Announcing the Dual Looping Delay from 4ms Company, designed by Gary Hall!

The 4ms Dual Looping Delay (or DLD) is an advanced audio processor for creative synthesis. Not a tape or analog emulation but a modern crystal-clear digital delay, the DLD combines features of delay, looping, and sample-tight synchronization for powerful and dynamic sound capture and modification. The DLD is designed to integrate seamlessly with modular time-base and sequencing devices such as the 4ms Quad Clock Distributor (QCD), etc.

What is a "Looping Delay"?
Modern looping devices grew directly from hardware digital delays of the late 70s and early 80s. A looping delay, modelled on units such as the classic Lexicon PCM42, has the very long storage times associated with dedicated looping, but without triggered record and playback functions.

By default, a looping delay records and plays continuously, though recording can be suspended at any time with Infinite Repeat. Sustain of delays and loops is mainly accomplished with regeneration, allowing an organic, evolving approach to sound creation as new material replaces old, more or less gradually. The 4ms Dual Looping Delay also provides advanced clock input and output facilities that allow for locking delayed and looped material with sequencers and rhythm devices of all descriptions.

The 4ms Dual Looping Delay is conceived and designed by Gary Hall. Implemented and manufactured by 4ms Company

Notes: The Spectral Multiband Resonator from 4ms Company is an innovative resonant filter which can process audio like a classic filter bank, ring like a marimba when plucked/struck, vocode, re-mix tracks, harmonize, output spectral data, quantize audio to scales, and much more...
A gorgeous ring of colored lights displays the frequency of each filter, as well as the levels and current scale selection(s).

At a glance, the SMR works like a normal six-band graphic EQ: six frequency band-pass filters are mixed together using sliders. Resonance/Q is variable, which changes the "ringy-ness" or width of the bands.

But here's where comparison stops. The frequency of each channel is treated like a note in a scale, and the six bands form a chord. Spin the Rotate knob and the "notes" circle around the scale, rotating back to the bottom once they've reached the top. Adjust Spread and the distance (interval) between each note changes. Triggers for up/down motion, CV inputs for sequencing and scale selection allow for flexible control with external modules. Morph, which automatically cross-fades between frequencies, together with variable Slew allows rhythmic clocks drive the SMR as a variable-speed evolving resonant filter.

At maximum Resonance/Q, the SMR can be struck like a gong or marimba by inputting clocks or triggers. The frequency of each channel is quantized to a scale: beautiful chords, ethereal tones and eerie ambiance flows easily. With lower resonance, the SMR can pull out particular frequency bands, and sweep these across the spectrum.

Two 1V/octave Frequency jacks allow for tracking even and/or odd bands and creating floating melodies over evolving chord bases, or complex percussive membrane sounds.

Save your settings into one of six storage banks, and recall on the fly. On startup, the SMR instantly jumps to the last saved settings. The color scheme of the lights can be adjusted, so if you prefer all white lights on your modular, you can have that (or all red, or rainbows, pastels, etc..)!

Advanced features:
- Program your own scale. The frequency of each of the 20 notes can be assigned by setting the octave, the semi-tone, and coarse and fine micro-tone. Up to 11 scales can be saved permanently in the user bank
- Adjust color scheme of the LEDs. Pick a pre-programmed color scheme or create your own using the sliders to set Red/Green/Blue values. Custom color schemes can be saved permanently
- Save your settings in one of six parameter banks. Note position, scale and bank selection, Q value, Lock settings and color scheme can be saved and recalled on the fly. On startup, the SMR loads settings from the last saved bank.
- Optional alternative filter type for a more exponential decay when plucked and different timbral qualities. Freq jacks no longer track 1V/oct in this mode.
- Slider LEDs can be assigned to display level for each channel (combination of slider position and CV on the jack), or clipping for each channel.

Notes: The Circadian Rhythms is moving modular synthesizer technology another step forward by gluing all the pieces of a system together. Each module or voice can now be programmed to play straight from an intelligent, eight-channel, 512-step master trigger sequencer made for composers looking to make music on the modular. Building on the sequencing concept of step programing multi-channel patterns of musical phrases can be repeated, looped, chained, muted and manipulated on the fly in real-time, and most importantly, all of this is done through a simple, clearly labeled interface. Using an array of multicolor illuminated buttons and innovative grid views provides a highly functional live performance sequencer with a beautiful glowing appearance of the programmed music that will look amazing on stage for both performer and crowd. As a master controller, the heart of the modular synthesizer, Circadian Rhythms generates high precision clock and reset signals for all the other sequencers and devices in the system to align with and can also act as a high precision bridge for DAW synchronization.

Views - Unlike most hardware sequencers that have a single static display of a timeline, Circadian Rhythms offers four different horizontal views of the timeline and two unique vertical views that scale from macro to micro. Switch between viewing 64 steps at once or all 8 channels side by side instantly. Stretch gates over multiple patterns to drive envelopes or use Zoom view to move a single hit back a few milliseconds in time to get the right feel all from the same interface.

LED Grid Built for Quick Access - Built around 72 buttons set as a multi-color illuminated 8x9 array, Circadian Rhythms displays both note data and settings in a clear and precise manner. It takes only one click to switch to vertical view and the grid turns into a set of programming and realtime playing functions like Mutes, Loops, Swing, Fills, Copy and Pate, Grouping, Randomizing, Manual trigger entry drum machine style and many many more. Activate any of those functions with only a button press or two.

Clock - Inside the CR ticks an extremely precise clock with jitter and latency measured in mere microseconds for the ultimate feel of groove. The four modes of clock sync make interfacing with other modules, hardware or software simple. Whether driving a large Eurorack system or synced to a DAW, the groove always remains tight.

SyncBus Technology - The Tiptop Audio designed SyncBus enables the CR to connect to any number of other SyncBus devices with the highest possible level of synchronization. A SyncBus master directly injects its core clock and running status into every connected unit so they work seamlessly as one device. Hook up two CRs to make a 16 channel device or add a Trigger Riot (or three) to the mix for further experimentation. Plus, the connection is done behind the panel so no need to patch anything together.

Under The Hood - When state of the art chip technology, musically driven firmware, and professionally engineered hardware design all come together in one electronic device, the result is a music sequencer with unparalleled specifications. Starting with a powerful, precise sequencing engine that has superb feel for the groove, add internal functions that automatically balance performance and smooth user interface operation, and finish with outstanding low power consumption placing minimal stress on power supplies even at maximum output, Circadian Rhythms has a design focused on the requirements of the most dedicated musicians and composers. Long time pros will immediately feel a machine made for their needs, while the newcomers can instantly dive into next level programming and performance.

Notes: The MKII version of the PDO is available: Better CV handling, 16 HP, single PCB instead of stacked boards. An upgrade path is available for those with MKI versions, contact us for more information.

Introducing the WMD Phase Displacement Oscillator (PDO). This hybrid VCO has all the feel of an analog VCO but with the benefits of digital waveshaping. The PDO will easily find a home in your system!

The PDO exists to utilize the phenomenon of Phase Modulation (PM). This allows for the relative phase difference of its outputs to be set or modulated, producing very interesting sounds. The result is similar to Frequency Modulation (FM) but affects the output to a greater degree without affecting the stability of the initial frequency. This is where the "displacement" comes in.

When you use frequency stable phase displacement, you create phase distortion which sounds like wavefolding and is very useful for dynamic textures and powerful sounds.

PM has the same benefits of quadrature filters/sine wave generators and greatly exceeds their capabilities at audio rate modulations. PM is highly useful for for creating metallic and bell tones and very controlled harmonic interactions.

Because PM affects the relative phase and not the frequency of the waveform generated, the PDO can self modulate its PM inputs. This creates complex harmonic signals that seem to vary in frequency but are quite stable.

Phase Modulation is also quite powerful when using the PDO as an LFO. Adjusting the relative phase of each output allows for very precise modulation of other modules. Each output can have any of the available waveforms simultaneously. There is a myriad of modulation possible with the PDO!

Notes: 'Akemie's Castle' is a dual voltage controlled oscillator with authentic 4 Operator digital FM using 'new-old-stock' Yamaha IC's for audio signal generation.

Each of the 4 operators feature independent waveform selection, frequency multiplier and level control via direct panel operation and voltage control. Operators can be combined in various ways across both oscillators, which together with independent feedback control on each VCO, offer an extremely wide palette of sounds.

Oscillator A also features a chord mode providing a range of up to 5 voice chords and voltage controlled inversion.

Notes: There is almost no modular system without at least one filter-module. You can look at them as the stars within the giant Eurorack-jungle. twinVCFilter is such a star as well. A dual filter module with flexible routing and excellent audio properties. It covers a huge range of different applications without the slightest effort.

Features and Routing:

Each filter section of twinVCFilter works as low- or highpass-filter with a slope of 12 dB/octave or as bandpass-filter with 6 db/octave. Signals can be directed in three ways through the module:

- Serial: The incoming signal passes both filter sections in a row.
- Dual: The filter sections act completely separated of each other. As if they were two individual filter modules.
- Parallel: The incoming signal passes both filters at the same time.

With these routings you can i.e. generate bandpasses or notches with variable slopes and different resonance settings or doubling the filter's slope. These are the more obvious combinations but there is a lot more to discover.

The convenient link-feature allows to couple cutoff- and resonance of both filter sections for straightforward stereo use in dual mode.

Mix section:

The flexible signal-routing is supplemented by the mix-section. Here you can crossfade both filter sections manually or by control voltages. Seamless movements from low- to highpass-filter, is as easy as crossfading from half to doubled slope. Of course you can mix two completely individual signals or toggle between them by using a rectangle-LFO-modulation.

Resonance:

Resonance is a key factor in the context of sound-shaping and sound-generation using a filter. Therefore we carefully trimmed twinVCFilter's resonance to be as musically and stable as possible. You can apply subtle frequency-dependent emphasis to signals and tear them up to self-oscillation. The latter generates a solid sine-wave which is an excellent base for percussive sounds. Possible cross-modulations significantly enhance the sound-generator features. By the way: If you are missing a vibrato-LFO in a patch, twinVCFilter can do the job.

twinVCFilter offers a huge set of features to form impressive soundscapes. It can take subtle influence to signals or massively truncate frequencies. It leaves nothing to be desired. Despite, for those who need additional possibilities we especially designed the tVCF-Extension module.

Notes: The SAPEL is a random control voltages source for Eurorack modular systems. It is composed of two main sections, one that generates audio noises, in 4 different versions, and another which includes two specular random clock, random voltages and clock sources.

Noise outputs are colour coded, based on the noise colours, and include:

- Blue (+3dB/oct spectrum)
- White noise (0dB/oct spectrum)
- Pink noise (-3dB/oct spectrum)
- Red noise, a.k.a. Brown or Brownian (-6dB/oct spectrum).

The random voltage and clock section features four uncorrelated random CV generation paths, divided in;

- Fluctuating random voltage;
- Quantized random voltage with 2n stages tuned in semitones referred to 1V/oct scale;
- Quantized random voltage with n+1 stages tuned in octaves referred to 1V/oct scale;
- Non quantized sample & hold.

It is also possible to set a probability distribution with a potentiometer, and apply (or do not apply) the chosen distribution setting to each of the four paths independently.

Furthermore, each of the two random sources section features an independent built-in clock generator, with clock output and random clock output, which can be used in "more than" or "less than" mode. It is possible to use an external clock signal as a clock source, bypassing the built-in one. In addition to that, it is also possible to hand trigger the clock via a manual sample & hold button, which can be also modulated by gate signals.

Notes: The Tapographic Delay is a complex multi-tap delay in the Eurorack format with a unique interface designed for live performance. It excels at transforming the simplest audio (a drone, a percussive sound) into complex rhythmic structures, meshes of organic textures, lush harmonic mille-feuilles, liquid and resonant effects.

Have you ever got tired of the monotonous repetitions that your standard delay pedal/module produced? Have you ever wished for a more complex rhythmic structure than just decaying repetition? If yes, you have come to the right place: the Tapographic Delay is an advanced effect that lets you handle repetition in a completely novel way. It is to a traditional delay what a full rhythmic sequencer (with pattern recall, velocity control, tactile input) is to a simple clock. With the TD, you interactively define the rhythm that the repetitions will follow: a velocity-sensitive sensor allows you to record, edit, modify, and sequence your own arrangements of delays. In a sense, the TD is the converse of the classic Frippertronics sound-on-sound setup popularized by Robert Fripp in the 70's: you don't play the guitar, you play the tape loop!

The Tapographic Delay is an expressive experimental instrument meant to be played in real-time, rather than a set-and-forget end-of-chain effect. Interact with it! Experiment! Push it to its limits!

Notes: Perfect for adding that final touch to a modular patch, the AJHSynth Finaliser R-EQ module includes seven Mono / Stereo reverb types, along with a four band equaliser and a Sonic Maximiser / Enhancer.

The Reverb, EQ and Maximiser can be used in Mono IN, Mono OUT mode or Mono IN, Stereo OUT modes. The reverb alone can also be used in Stereo IN / Stereo OUT mode too.

The fully analogue four band Equaliser includes three parametric equalisers for Low, Low Mid and High Mid ranges, and the High EQ has switchable shelving of either 2kHz or 5kHz. The Low EQ also includes a shelving mode.

The Maximiser is a fully analogue circuit too, with low and high treatment bands which change the phase and amplitude relationships of the sound to add punch and harmonics and really bring the sound to life in the mix.

The Reverb engine is based on 20 year old DSP technology, harking back to the reverb units which were used extensively on many synth and EDM tracks a couple of decades ago. We have added full control of reverb wet / dry mix, either manually or under CV control.

Notes: Excellent Eurorack sequencer based on random chance and evolving patterns. Dial in a series of notes and build melodies, generate and tweak patterns in real time. Huge depth for studio production or live performance.

Supplier's Notes:
The Melodicer from Vermona is a CV/Gate sequencer with an innovative concept; the melody sequencer offers twelve faders for setting the note probability and two dice-(or random) buttons for generating melody and rhythmic structure.

Notes: Record. Mangle. Destroy.

Nebulae is a granular sampler and DSP platform. Its phase vocoder audio engine provides elastic audio, which can be time stretched, granularized, and mangled to no end. With independent control over pitch and speed, and granular controls such as overlap, window, and density, finding new sonic territory is only a knob turn away. Nebulae can use live audio input, a recorded buffer, or audio files as the source material for its powerful audio manipulations. The live input buffer can record up to five minutes of stereo audio at 48kHz, 24 bit. In addition, up to 75 MB of stereo audio can be loaded simultaneously through the USB port. No naming convention or special formatting necessary; just plug and play.

Nebulae lives a double life as an open source DSP platform with an extensive library of off the shelf alternate instruments. You can turn the module into a lush reverb, spectral delay, or tape-style looper simply by loading a new file onto the flash drive. Do you want to tweak one aspect of an existing instrument, even the default functionality? No problem. No prior coding knowledge is necessary to tweak and refine existing firmware to your liking or start with one of our templates. Alternate firmware files can be written with Pure Data, Csound, SuperCollider, and even bare-bones C programs.

Notes: The Stereo Triggered Sampler can record high quality stereo files, while simultaneously playing two different stereo files. A maximum of 600 samples can be loaded from the removable/swappable microSD card, in a variety of formats up to 96kHz/32-bit/stereo WAV. All sample parameters (1V/oct pitch, sample file selection, length, and start position) are CV controllable.

600 Samples:
A maximum of 600 samples can be loaded at once, arranged into banks of 10 samples each. Samples and banks can be re-arranged on the fly using the simple on-board Edit features. Newly recorded samples can be instantly played back and re-pitched, reversed, chopped up, etc... the result of which can even be bounced down and re-recorded to as a new sample! Sample files are limited to 4GB each, which is over 6 hours at 44k/16b/stereo.

Two Stereo Playback Channels:
Each playback channel has a knob and CV jack for Sample File selection, as well as a Start Position knob and CV jack for controlling where in the sample playback will begin. The Length knob and CV jack determine how much of the sample is played back: from tiny grains, to percussive hits, to longer loops... or just the entire file. These are powerful tools for re-arranging a sample, joining multiple samples, and creating dynamically re-sized loops within a larger sample. Combined with the Play Trigger jack and the 1V/oct jack, the STS can be two complete multi-timbral pitch-tracked stereo voices!
There's also a Reverse button and jack for backwards playback, and an End Out jack for synchronizing loops, or cascading sample playback with other events.

Looping and Sync:
Looping is easy: just hold the PLAY button down for two seconds to toggle loop or one-shot. The loop timing clock will output from the End Out jack. Or, send a clock into the Play Trig jack to sync the loop to external timing.

Stereo Recording:
Whether you patched 47 modules to create the ultimate percussive blast, or you want to capture your four hour ambient performance, recording high-quality .wav files on the STS is simple. Just hit the REC button or fire a trigger and a new stereo .wav file will be created on the SD card. Do as many takes as you need: the STS never deletes your files. Re-ordering or re-arranging samples into banks is easy, even without a computer.
You can even fill a bank with 10 different variations and immediately use them for playback.
By default the STS records at 44.1kHz/16-bit, with an option for 24-bit (a future update may increase the sample rate to 96kHz)

Easy sample loading:
Using a computer is completely optional with the STS, since samples can be recorded directly to the module and placed into the bank of your choosing. But for users with large existing sample banks, the intuitive automatic bank loading features make dragging and dropping your entire sample library a snap. You never have to rename your files again!

Notes: At the core of the EVOLUTION Variable Character Ladder Filter is Dave Rossum's enhancement of the iconic Moog ladder filter from the original E-mu Systems 2100 LPF module (which, incidentally, Dave counts as his favourite sounding of all of the analog filters he designed).

For EVOLUTION, Dave has designed new capabilities that not only allow you to dial in all of the outstanding qualities of the original 2100, but combine to let you create the sonic characteristics of a wide variety of other filter types.

They include:

- A Genus control that allows continuous voltage control of the number of filter poles (from 3 to 6 poles), essentially allowing real-time variation of Evolution's effective cutoff slope from 18dB/oct to 36dB/oct. LEDs give continuous indication of the current slope.
- A Species control that lets you vary the signal level into the ladder, letting you control the intensity of the filter's characteristic distortion. When in self-oscillation mode, this control modulates the amplitude of Evolution's output.
- Voltage controlled resonance with a variable Q Level Compensation control that controls the balance of the resonant peak and the frequencies below the cutoff frequency (which would otherwise be attenuated as the resonance is increased).
- An extremely accurate and temperature-stable frequency control exponential generator (accurate over 10 octaves), rivalling the specifications of the best analog VCOs.

Taken together, EVOLUTION gives you everything from the platonic ideal of the classic ladder filter to a vast selection of alternative filter characteristics.

And like all Rossum Electro-Music modules, it's solidly built, with machined aluminium knobs and high quality components throughout.

Notes: Killer physical modelling module collab from two of the biggest names in their respective fields of hardware and software. Generates a huge range of percussion instruments plus synths and bass tones.

Supplier's notes:
Plonk uses a technique known as physical modelling to synthesize, with great realism, the way in which sound is produced by acoustic instruments. The Plonk module is, itself, focused primarily on creating percussive sounds - both pitched and un-pitched; natural and unnatural; acoustic-sounding or totally electronic.

Plonk does this by breaking sound creation into two distinct elements - the exciter and the resonator. The exciter is a mathematical model of the device used to strike a particular surface. Plonk, because it's percussion oriented, has two types of exciters: one modelled on a mallet, and the other providing a noise source. The resonator is a virtualization of the object being struck, which vibrates, resonates and creates the body of a sound. Plonk offers several types of resonators: beam; marimba; drumhead; membrane; plate; and string.

Plonk provides numerous parameters that let you shape, mould and design both the exciter and the resonator, thus enabling you to synthesize the sound of striking or scraping almost any type of object - real or imagined. In this way, Plonk can accurately model the sounds of kicks, snares, toms, cymbals, claps, tablas, congas and all manner of traditional percussion instruments. It can also model pitched percussive instruments, like vibes, marimbas, and even bass or guitar-like tones. Of course, it additionally excels at modelling instruments that heretofore never existed.

Best of all, the sounds created by Plonk are not static - any sound you design can respond dynamically to velocity, as well as four different modulation inputs. This means the sound of Plonk can change completely from note-to-note (or strike-to-strike). Because of this, Plonk is actually a duophonic (2-voice) module, which lets the sound of one note decay naturally when a second note (possibly employing an entirely different set of modelling values) is struck. Thus, hitting a new note does not choke the sound of the previously struck note (unless you want it to, of course)!

Plonk stores up to 128 patches in its internal memory, and ships with many presets programmed by professional sound designers and composers. You may overwrite these patches if you wish, and banks of patches may be transferred via MIDI System Exclusive over Plonk's built-in mini-USB port to facilitate offline storage by programs or websites that support this capability.

Plonk was developed in cooperation with Montreal-based Applied Acoustics Systems - physical modelling pioneers, and the creators of Tassman, Lounge Lizard, String Studio, Ultra Analog, Chromaphone and numerous other plugins. It is with great pleasure that Intellijel brings the potential of this physical modelling technology to a hands-on, CV-laden device capable of the sort of dynamic control and sonic exploration that modular synthesists demand.

Notes: A duophonic percussion/drum module which offers you two individual, almost identical voices. Each of them has an oscillator with selectable waveforms as well as an attack-decay envelope which simultaneously can modulate the pitch and the VCA.

A large number of sockets is available which not only are used for modulating and triggering the drums but also emit any oscillator waveform and envelopes. That is utterly useful!

The first difference between both voices are the available waveforms: voice A offers square, triangle and sine, while voice B has noise, square and sine. For atonal noisy sounds like hi hats and anything cymbal voice B is more suitable.
The wave forms are switch selectable and simultaneosuly available at individual outputs i.e. you can process the audio signals exernally. Using the module's EG CV outputs plus two external VCAs you can re-create or alter the signal flow. Envelope signals and audio sources are available!

For controlling the frequency there's a hi/lo switch alternating between bass and treble, then a tune control and a modulation attenuator which scales either the envelope or a nexternal CV. besides individual inputs (A VCO and B VCO) there's also a common CV input VCO A+B which addresses both voices simultaneosuly. A VCO is normalized to the VC CV input A VCA, analogical for channel B.

The second difference is in the envelopes. Voice A has an attack-decay envelope generator with manually adjustable times. Voice B has a decay envelope with fixes attack time but with voltage control of decay time via EG 2 input and the CV EG2 attenuator.
The envelope generators are able to modulate not only the pitch but simultaneously also the level. For that reason there's an second attenuator which altternately detemines the intensity of an external CV (see above).

Each voice has an individual audio output, although OUT B works as a mix output when no cable is plugged to OUT A.

*essentially two things have changed in the + version:
-the output levels of the MIX outputs have been increased
-the frequency of the filter for noise can now also be controlled via CV

Power consumption: 105mA at +12 V and 70mA at -12 V
Depth: 45mm
HP : 24

Notes: Cursus Iteritas is an oscillator that works from a dynamically generated wavetable. It gives the user spectral-like controls over three different modes based on different conceptualizations of frequency: Fourier, which uses sine waves; Daubechies, using wavelets, and Walsh mode, using the Walsh transform. Cursus Iteritas parametrizes a wide variety of sounds, but because the sounds are all based on orthogonal functions, it has a musical tone structure and can produce an extremely wide variety of harmonic sounds.

Size: 10HP Eurorack
Depth: 1.5 Inches
Power: 2x8 Eurorack
Draw +12V: 150 / 80
Draw -12: 5 / 5
Draw +5v: 0 / 90

Notes: Loquelic Iteritas is a digital VCO with interpretations of three classic synthesis algorithms involving dual pitch control. It creates a huge variety of sounds parameterized by four tone and two pitch controls.

It has had glowing reviews from Surgeon and Surachai, and I am personally very excited about this module!

It has a simple interface, with 3 different synthesis algorithms allied to a number of different controls / CV inputs which have different effects, depending on which mode you choose. Simply hook up a number of modulation sources to the 4 inputs and start wiggling!

Rev.2 now features an additional sync input.

Size: 10HP Eurorack
Depth: 1.5 Inches
Power: 2x8 Eurorack
Draw +12V: 150 / 80
Draw -12: 5 / 5
Draw +5v: 0 / 90

Notes: Hugely powerful multi-engine synth module, offering up to eight voices and eight oscillators, sample playback, custom wavetables and much more. Ultra versatile.

Supplier's Notes:
8 full voice polyphonic, multipart, multi engine synthesizer module with sample playback, sweet reverb and chorus.

Create pads, basslines, riffs and drums. All in one module.

Group voices into parts and assign each voice a different engine or parameter settings to create complex patches.

Features:

Big Sound

Lots of computing power to deliver rich sounding engines, in an 8 voice package.
One voice can have 8 oscillators depending on the engine, which means up to 64 oscillators at the same time!

Polyphonic

Coral features 8 full voices with independent filter, amplifier and modulation envelopes per voice.
Individual FX sends and individual parameter can be set per voice!

Multiengine

Different sound engines can be assigned to each voice from the 10 available.
New engines will be available through firmware updates.

Multipart

The 8 voices can be freely split into different parts. Every single parameter (filter, envelope settings, engine, FX sends, pan, etc.) can be independently set for each part or voice to create complex patches out of the box.

Sample playback

CORAL supports almost any kind of wav file: 16, 24 and 32 bit mono and stereo files, no limit to playback time!
Add overdrive to your samples, sculpt them using the filter and envelopes, pitch them up and down in tune and even modulate the sample file or folder in real time using the CV inputs or CC MIDI commands!

Custom wavetables

You can load any wavetable .wav file to the SD card for the Wavetable engine. The wavetable can be morphed in 3 dimensions. Use our OXI Wave APP to create and edit 3D wavetables.

MIDI Integration

Control any part's parameter via MIDI CC, from FXs sends to sample selection.
Combine it with CV signals for a killer compact combo.

Effects

Space engine to create deep atmospheres and rich ensemble chorus.
Every effect send can be set per voice

Notes: The Precision VCO (PCO) is Serge's legendary oscillator. It combines raw vintage sound with astonishing precison.

The PCO is a versatile, voltage controlled oscillator now offering four high quality waveform outputs (sine, triangle, pulse and sawtooth) and both linear and exponential frequency modulation capabilities . A front panel switch conveniently extends the range of the PCO from the audio range (16 to 16,000 Hz) to a sub-audio range (.1 to 200 Hz) for use as a Low Frequency Oscillator.

EXCELLENT RESPONSE, TRACKING AND STABILITY: Featuring the identical exponential response, exceptional tracking characteristics, and perfect temperature stability as the NTO, the PCO is especially suited for use with the NTO or another PCO as a modulation source for dyanamic depth linear FM.

Two calibrated one volt per octave inputs as well as a variable processing input are provided for complex frequency control. FM depth can be varied with the front panel adjustment. A Sync input is also available for locking the PCO to another oscillator's fundamental, harmonic, or sub-harmonic frequency.

The Serge PCO is the only authorized version of Serge's classic design.

Some details of the Serge PCO eurorack module:

Authentic Serge design
Now with PULSE OUT
Variable oven temperature
Manufactured in Germany
Eurorack (3U) format, 18 hp
Power consumption: 75mA @ +12V, 60mA @ -12V
Skiff-friedly, Module depth: < 30mm

Notes: The Shaped Dual EnvVCA is a two-channel analogue envelope generator with waveshapers and a stereo linear VCA. Unlike conventional analogue envelope modules, the waveform of each envelope can be controlled with a slider or CV without changing the envelope timing. With a wide time range from an hour to 2.5kHz, and a plethora of CV inputs and attenuverters, it can be used as an LFO, audio-rate oscillator, slew limiter, waveshaper, ASR/ADSR/complex EG, independent audio/CV VCA, envelope follower, sidechain processor, and general utility module. Each channel has dedicated linear outputs plus attenuverters and offset controls for the variable waveshape outputs, making it an ideal modulation source and stereo VCA.

100% analogue

Shaped Dual EnvVCA

20HP Eurorack format module
0.95" (24mm) maximum depth (includes power cable)
10-pin Eurorack power header

Power consumption
+12V: 255mA
-12V: 230mA

Audio/VCA
100k input impedance, 1k output impedance, DC-coupled
VCA gain range: -90dB to +2.0dB, linear response to CV from 0V to 5V
VCA unity gain: 4.4V CV
DC to 20kHz, +/-0.1dB

Envelope Times
Minimum rise or fall time: ~200us per segment (2.5kHz max frequency)
Maximum rise time: >20 minutes (typically > 40 minutes)
Maximum fall time: >12 minutes (typically > 20 minutes)

Jacks:
Env jack: Min = -10.2V, Max = +10.1V, maximum amplitude 9.3Vpp
Trigger jack: rising edge threshold = 1.25V
Follow jack: active range = 0V to +5V

EO* jacks:
EOR (channel A): <80mV low to >4.50V high gate output
EOF (channel B): <80mV low to >4.95V high gate output
Minimum stable pulse width: 1ms. Shorter than this may produce extra 50us pulses
Audio In/Out jacks: -10V to +10V maximum range without clipping

Notes: The Haible VC Resonator is an evolution of Jurgen Haible's Resonator which was inspired by the Polymoog Resonator. As Jurgen stated: The Polymoog, an early polyphonic synthesizer, featured a 3-band "Resonator" section that allows Formant-Filtering in addition to its dynamic Filters. Such a Resonator is a very useful feature for analogue synthesizers. Each of the three (now overlapping) filter bands has a control for frequency, signal gain, and emphasis (resonance). The VC Resonator now not only adds VC control for each band, but also extends the ranges whithin which each frequency band can be set - adjacent bands can now overlap or even cross over, for instance the LOW and MED bands can now be set (or moved!) so that the LOW center frequency is higher than the MED frequency.

Jurgen's original Resonator (like the Polymoog) had a switch to select one of 3 basic modes, i.e. only one mode could be used at a time. The Haible VC Resonator now provids the same 3 modes as separate outputs so they can be used simultanously, e.g. for further processing like crossfading.

Some details of the Haible VC Resonator:

Evolution of Jurgen Haible's design
Added Voltage Control for Filter bands
Extended range of each band (overlapping)
Three separate outputs
Burr-Brown op-amps and high-end VCAs
Eurorack (3U) format, 18 hp
Skiff-friendly: < 30mm deep
Power: appr. 60mA @ +12V and 60mA @ -12V

Notes: Building on the familiar dual VCO core arrangement of Carrier and Modulator, Mindphaser is a complex oscillator which departs from this bit of ancestral DNA with a modern toolkit focused on searing, phase-modulated leads, percussive basslines and other-worldly effects!

A diverse palette of intermodulation and harmonic experimentation is offered through the Modulation Bus, its unique Waveshaper and the dedicated Thru-zero Phase Modulation Bus. An intuitive interface provides colour-coded visual feedback and responsive indication while performing in dimly-lit environments.

Two precision analogue oscillator cores

Precision, wide-range V/oct ramp cores, each ranging from deep subsonic to supersonic frequencies (ramp cores, and not triangular, deliver the ideal waveforms for analogue phase accumulation in the TZ-PM Bus)
Each core generates fundamental waveshapes which interact and mangle one-another through the complex Modulation Bus and TZ-PM bus
Simultaneous waveform outputs for each base shape
Dedicated button to toggle between RAMP or SAW for each core, inverting the phase of the ramp output
V/oct, linear FM and exponential FM inputs which are all independent of the TZ-PM functionality. The Carrier's FM occurs inside the core itself, separate from the TZ-PM bus.
DC-coupled linear FM

Carrier

The heartbeat of Mindphaser, focused on audio-rate generation. Drives the WAVESHAPER and TZ-PM bus. This core's frequency range spans the audible spectrum.

- An external hard SYNC IN forcibly resets the core, useful for punchy sequences, percussive basslines and drum synthesis -- or to sync to another VCO.

- Coarse and fine controls conveniently span the audible spectrum. Ranges further with external CV.

Modulator

An extremely wide range oscillator, spanning from deep LFO frequencies all the way up to supersonic sound! Four base waveforms and diverse internal routing options form a versatile palette of modulations for the CARRIER to feed on.

- Activating hard SYNC on the Modulator locks its core to the Carrier's heartbeat. The effect can be dramatic. Try this while phase modulating!

- Octave RANGE switch lets you quickly flick up and down between octaves. All the way beyond audio-rate and LFO speed octaves. Perfect for experimenting with different PM sidebands and taming the wide frequency range of the Modulator.

- Manual PW (Pulse Width) control and dedicated CV input for PWM.

Waveshaper

This isn't a classic waveshaper! Developed anew from the ground up, this waveshaper is focused on deep harmonic experimentation and audio obliteration. Each waveshaper parameter is capable of being "turned up to 11".

FOLD up to 5 octaves above the fundamental Carrier frequency. A ceiling forms at maximum, imparting additional harmonics.

FEEDBACK the waveshaped and phase-modulated audio through a signal path internal to the waveshaper.

AMPLITUDE modulation spans thru-zero, allowing for full-range ring modulation effects with bipolar CV or audio signals.

CLIP the final stage of amplitude with the switch to introduce a last stage of harmonics before the complex signal exits through the final OUT.

Switchable inverting attenuators on each CV input, for quickly inverting the behaviour of your modulation. The indicator illuminates red to tell you the attenuator has been inverted.

Two distinct waveshaping modes

A press of the shape switch toggles Mindphaser between RAMPOID (green) and TRIANGULAR (yellow) waveshaping modes.

These modes have a remarkable effect on the behaviour of wavefolding and overall character of the final complex OUT, in addition to TZ-PM Bus character.

RAMPOID mode folds more asymmetrically, with raucous, buzzing harmonic artefacts as you sweep and introduce TZ-PM

TRIANGULAR mode folds more symmetric, splitting the complex sine wave at its peak centre of the waveform. TZ-PM character is less raucous, and more smooth.

TZ-PM Bus

Thru-zero phase modulation in the ANALOGUE realm! Unlike its digital counterpart, analogue TZ-PM has its own character we've come to expect from analogue circuitry!

A dedicated, voltage-controlled phase modulation bus completely separate from the Mod Bus
Modulator's SINE wave normalled to the PM SOURCE input
SOURCE input allows you to modulate phase with any signal you patch in
Dedicated voltage-controlled INDEX (amount)
Manual phase lets you zero in (or not!) on the base phase before introducing modulation
Independent of the Linear FM circuitry in the Carrier core

Mod Bus

The internal modulation powerhouse, normally fed by the Modulator core, but external signals are patchable as well.

Select from the PULSE, RAMP/SAW or SINE output of the MODULATOR, or inject your own SOURCE to the bus.

Voltage-controlled INDEX behaves like a macro control when combined with various amounts and polarities dialled in at each CV destination.

Internal sends include the Carrier's classic Linear FM, Amplitude, Feedback and TZ-PM Index, with variable amounts and polarities!

Modulator waveforms internally feeding the Mod Bus behave unipolarly, for predictable modulation of every Mod Bus destination, without external patching. By patching in one of the Modulator's bipolar waveform outputs manually (or any external signal), you can override this behaviour.

Dimensions
30 HP
24 mm deep

Current Draw
110 mA +12V
100 mA -12V

Notes: ***B-STOCK: Box opened, product in excellent condition, no original internal packaging***


Intellijel has made the already awesome Thru Zero VCO Rubicon even better! In addition to the seven waveforms plus sub-oscillator of the first version, the second generation offers a new Warp stage, which generates a hybrid of complex pulse and other waves - you can even use external audio material. In order to keep results in the range of 10 Vpp, there is a wave folder called Squish. On top, the FM capabilities were expanded.

Notes: ***B-STOCK: Box opened, product in perfect working order***


Record. Mangle. Destroy.

Nebulae is a granular sampler and DSP platform. Its phase vocoder audio engine provides elastic audio, which can be time stretched, granularized, and mangled to no end. With independent control over pitch and speed, and granular controls such as overlap, window, and density, finding new sonic territory is only a knob turn away. Nebulae can use live audio input, a recorded buffer, or audio files as the source material for its powerful audio manipulations. The live input buffer can record up to five minutes of stereo audio at 48kHz, 24 bit. In addition, up to 75 MB of stereo audio can be loaded simultaneously through the USB port. No naming convention or special formatting necessary; just plug and play.

Nebulae lives a double life as an open source DSP platform with an extensive library of off the shelf alternate instruments. You can turn the module into a lush reverb, spectral delay, or tape-style looper simply by loading a new file onto the flash drive. Do you want to tweak one aspect of an existing instrument, even the default functionality? No problem. No prior coding knowledge is necessary to tweak and refine existing firmware to your liking or start with one of our templates. Alternate firmware files can be written with Pure Data, Csound, SuperCollider, and even bare-bones C programs.

Notes: ***B-STOCK: Box opened, light surface marks, product in perfect working condition ***


Inspired by Roland's TR-x0x sequencers, the Drum Sequencer brings that classic approach to Eurorack, offering a massive 16 trigger channels with gate and accent outputs, plus a CV/gate track for synths.

Supplier's notes:
X0X-style beat creation for modular systems - Erica's drum sequencer is based on the concepts of classic Roland TR rhythm composers. The module offers 16 trigger channels, twelve of which also feature accent outputs. Additionally, there is a CV and a gate track, meaning you can also notate a bass line or melody. The maximum pattern length is 64 steps. Extensive playback and random functions plus two LFOs help you with creating lively results. Large buttons provide a fantastic feel while programming patterns.

Notes: Gross, gritty, and dark industrial-strength voice on a swappable oscillator platform. Pangolin approved.

Manis Iteritas Alia is a voice based on the architecture of Basimilus. It was designed to be grittier and more aggressive by using only sawtooth waves that are manipulated, modulated, and distorted through a rethought interface. Manis Iteritas Alia is fantastic for leads, basslines, drums, darkness, detuned swarminess, or pure mayhem. Plus, MIA's dedicated envelope output is a great modulation source for the rest of your patch.

MIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal to check out any other Alia firmware, free of charge, any time.

A portion of the proceeds of every Manis Iteritas Alia sold goes to pangolin conservation.

Width: 10HP
Depth: 22mm

Notes: Cleverly designed melodic looping sequencer/sampler, offering four pattern banks each with 16 steps, aiming to bring 'DAW-style' workflows to Eurorack - sample reversing, pitch shifting, and so on.

Suppliers notes:
Torus is an overdub looper for harmonic playback. It offers four, 16-step pattern banks for sequencing as well as other sample manipulation techniques. It was designed to bring daw recording workflows (sample reversing, pitch shifting, sequencing, etc.) to eurorack cases.

Inputs:

A, B, C, D - buttons for choosing the current pattern. When combined with chain, these buttons can be used to sequence a pattern chain. Individual chains can be support 16 steps and are kept in sync with torus's global clock.

Chain - button for chaining behaviours. Chain + A, B, C, D can be used to sequence a pattern chain. Chain + record can be used to record multiple patterns in series and then chain playback. Chain + clear can be used to clear all recorded patterns. Chain + tap can be used to reset the current pattern when it contains recordings.

Mix - knob and CV used to blend between the input signal and the recorded pattern.

Record - button and gate in for turning on and off recording. When a pattern is not recorded, record will turn on and in sync with the clock. When a pattern is recorded, record will immediately turn on and off overdubbing.

Oct - buttons for octave shifting pattern buffer playback. Oct buttons can be used to clock divide/multiply an input clock signal.

Reverse - button and gate in for reversing buffer playback.

Harm - knob and CV for choosing harmonic pattern playback speeds. Playback speeds include both integer clock multipliers and perfect intervals.

Tap - button for tapping in tempos for the internal clock. Tap will repeat the current note when the current pattern contains recordings. Combine with chain to reset the entire pattern when the current pattern contains recordings.

Clear - button and gate in for clearing the current pattern. Combine with chain to clear all recorded patterns.

Clock - gate in for clock syncing

In L and in R - audio input, left will be converted to stereo if there is no right input.

Outputs:

Harm out - gate output mapping to harmonic playback resets. This gate output will range from 1-16x the clock out frequency depending on the harm knob/CV value.

Clock out - gate output for the global clock. The output gate frequency will be 0.25-4x the input clock speed based on the oct button state.

Reset - gate output when the current pattern has reset.

Out L and out R - audio output

100 mA +12V 40 mA -12V 0 mA 5V

16 HP 35mm deep

Notes: Monolith is a pitch-shifter reverb inspired by west coast synthesis techniques. It utilizes a time-domain based FM algorithm that acts as a shimmer.

Inputs:

In L and In R - audio input, left will be converted to stereo if there is no right input
Blend - knob and CV for controlling the fade between the dry and FM audio signals
DJ filter - knob and CV for controlling the reverb delay line filtering
Wet - knob and CV for controlling the reverb decay
Mod - knob and CV for controlling the scale of FM modulation. Low mod values correspond with microtonal pitch regions. High mod values correspond with multiple octave shifts.
On - button and CV gate for toggling on/off FM modulation. When FM modulation is turned on/off, the FM modulator oscillator is reset.
Quant - button and CV gate for toggling on/off FM pitch quantization.
Freq and v/oct - knob and CV for controlling the frequency of the FM modulator oscillator. Also control reverb pre-delay.
Shape - knob and CV for controlling FM modulator oscillator shape. Shape wavetable transitions from sine wave (8 o'clock) to triangle wave (12 o'clock) to square wave (4 o'clock).
Clock - CV gate for tempo syncing modulator oscillator period.

Outputs:

Out L and out R - audio output
Gate - CV gate out that is period synced with the FM modulator oscillator

100 mA +12V 40 mA -12V
14 HP 35 mm deep

Notes: Alter is an effects processor for Eurorack format. There are two versions of the Alter which are visually identical except the names "Alter 1" and "Alter 2". This is Alter 1. Internally, 1 & 2 have an entirely different set of effects from the other. Each version features 7 unique and meticulously designed DSP effects.

Control

- Controls for mix, X, Y and Sift as well as clock.
- All effects have a variation of a filter which may change effect to effect.
- X and Y control various rates, feedback and time over the different effects (note that some of the images shows a prototype which says "rate" under two of the pots. The faceplate has been changed to X and Y).
- Clock control adjusts the rate which controls the DSP which can drastically change the effect. In doing so it does slightly lower the quality of the output signal but the results are fantastic. This clock is not for synchronization.
- Mix, X, Y and Sift all have CV control inputs.
- Each control level or CV input is visualized on the control panel.

Ins and outs

- Stereo inputs with separate level/gain control for right and left channels. These levels can also act as mute as it can take the signal to 0. They can also add gain to a quiet signal.
- Peak level indicator for clipping levels at the input
- Mono input is made stereo within the DSP and outputs to both left and right channels
- Stereo outputs for right and left channels

Effects

The effect is selected by the hexagonal touch pad. The effects for Alter 1 are as follows:
1 - long delay
2 - tight, notated granular delay
3 - plate reverb
4 - shimmering reverb
5 - distortion multi-filter
6 - pitch delay
7 - stutter glitch

Specs

Includes printed manual
+12V: 160mA
-12V: 0mA
+5V: 0mA
16HP width
25 mm Depth

Notes: Alter 2 is an effects processor for Eurorack format. There are two versions of the Alter which are visually identical except the names "Alter 1" and "Alter 2". This is Alter 2. Internally, 1 & 2 have an entirely different set of effects from the other. Each version features 7 unique and meticulously designed DSP effects.

Control

- Controls for mix, X, Y and filter as well as clock.
- All effects have a variation of a filter which may change effect to effect.
- X and Y control various rates, feedback and time over the different effects.
(note that some of the images shows a prototype which says "rate" under two of the pots. The faceplate has been changed to X and Y.)
- Clock control adjusts the rate which controls the DSP which can drastically change the effect. In doing so it does slightly lower the quality of the output signal but the results are fantastic. This clock is not for synchronization.
- Mix, X, Y and filter all have CV control inputs.
- Each control level or cv input is visualized on the control panel.

Ins and outs

- Stereo inputs with separate level/gain control for right and left channels. These levels can also act as mute as it can take the signal to 0. They can also add gain to a quiet signal.
- Peak level indicator for clipping levels at the input.
- Mono input is made stereo within the DSP and outputs to both left and right channels.
- Stereo outputs for right and left channels.

Effects

The effect is selected by the hexagonal touch pad. The effects for Alter 2 are as follows:
1 - Analogue delay
2 - Reverb with infinite capture and LP + HP filters
3 - Choral reverb
4 - Palindrome reverse delay - backward/forward repeat
5 - Time stretch
6 - Pitch shift (notated semi-tones)
7 - Time stretch glitch

Specs

Includes printed manual
+12V: 160mA
-12V: 0mA
+5V: 0mA
16HP width
25 mm Depth

Notes: TRILOBITE is a triple oscillator analogue module inspired by the original Moog schematics and made with thru-hole components only.

The module features:

- 4 octave ranges
- 3 waveforms (triangle, square, saw),
- UNISON (FINE) control with a range of +/- 12 semi-tones
- Independent LIN FM and PWM inputs with attenuators
- White noise source

Independent audio output is provided for each oscillator. A mixed output is also present featuring a level control.

We are recommended to use independent audio outputs to avoid distortion, in this case MiX output works as WHITE NOISE source with attenuator.

V/oct input of the first oscillator is normalled to all 3 oscillators, so OSC2 and OSC3 would track it too, however, connecting other signals to the other V/oct inputs make each input independent.

The minimum frequency of each oscillator is as low as 3Hz which makes it possible to use them as LFO.

Each oscillator tracks up to 9 octaves.

V/Oct range: 0-10 V

NB: Trilobite as is a full analogue module so should be allowed 5-7 minutes to warm up before use.

* 26HP
* skiff-friendly (25mm depth)
* 200 mA +12V
* 180 mA -12V
* 0 mA +5V
hand-built in Kyiv, Ukraine

Notes: MachineRoom PRODIGY DUAL VCO is an analogue dual oscillator based on the legendary Moog Prodigy synth schematics. MachineRoom improved Bob's design by incorporating ICs with better thermal stability, increased the range of secondary oscillator, and also added cross-modulation possibility. As usual for this limited run of full-analogue handmade modules, MachineRoom used only thru-hole components.

The module features 3 octave registers and 3 waveforms per oscillator.

OSC1 generates SAW, SQUARE, and TRIANGLE waves with 8, 16, 32 octave registers.
OSC2 generates SAW, PULSE, and TRIANGLE waves with 4, 8, 16 octave registers.

Unlike the original version, PRODIGY DUAL VCO allows switching OSC2 to the LFO mode to modulate OSC1 or other parameters (LFO range is from 0.1 Hz to 8.6 kHz). Precise pitch tracking is up to 7 octaves.

PITCH control has a range of +/- of 1.5 octaves with a central point (to have the ability to quickly return to the initial frequency with precision). The rise/fall time of the GLIDE/SLEW is up to 5 seconds

HARD SYNC switch allows syncing the phase and frequency of oscillators.
LINEAR FM input has a built-in attenuator.

OSC2 UNISON control has a range of +/- 7 semi-tones (increase/decrease relative to the Detune central point).
OSC2 V/Oct Tracking switch activates or disables the OSC2's LFO mode. When disabled, OSC2 stops v/oct tracking, and the UNISON knob becomes a control for the LFO frequency.
OSC1 - OSC2 FM switch enables OSC2 as an OSC1 modulator.

When HARD SYNC is switched ON, Pitch/Sync knob controls the phase of oscillators.

The output level of each oscillator is about 3.5V which allows passive mixing. PRODIGY DUAL VCO is analogue so should be allowed 5-7 minutes to warm up before use.

Skiff-friendly design.

Thru-hole components only

20HP / 35mm deep

Current consumption:
+12V - 125 mA
-12V - 105 mA
+5V - 0 mA

Hand-built in Kyiv, Ukraine

Notes: Sixteen Seconds Delay vintage eurorack version, inspired by the original looping delay from 1983.

The device topology is the same as first digital delays from that era, with an all-analogue signal path, pre emphasis and de-emphasis, compression and expansion, antialias and reconstruction filtering and input output buffering and mixing.

Digital processing is limited only to analogue to digital conversion, memory management and storage and digital to analogue conversion, all in glorious eight bits.

There's also an analogue triangle Low Frequency Oscillator for modulating delay time/pitch Maximum delay time has been increased to 32 seconds, there are toggle switches for slow/fast speed/pitch , freeze function and reverse playback.

On board modular inputs for CV control of sample rate, infinite/freeze, reverse, slow/fast, reverse, delay line retrigger for sync and stutter experimentation.

Slider illuminated controls are delay time coarse, delay time fine, sweep rate and depth, feedback and mix.

Proudly hand built in Uruguay, by Maneco Labs also creators for the Grone Drone machine Eurorack, Tabletop and Pedal drone generators among others.

Notes: The Dannysound Dynamics is a compressor / expander originally designed to process drums but, like most processing devices, it can be used for a wide variety of applications.

The module comprises of:

Compressor / Expander
Sub Bass Enhancer
3 Band Inductor-based EQ
Harmonic Exciter

The compressor / expander section uses a discrete transistor-based circuit that allows for soft clipping when overdriven.

The envelope detector is known as a feedforward type of circuit; taking its input from the signal before it goes to the compressor rather than after. This type of circuit is known for having fast attack times.

The Sub Bass enhancer has its own compression circuit that "ducks" the initial transient. This allows the sub bass to be increased without distortion on the transient peaks, increasing the overall level.

There is a MIX control to allow the unprocessed signal to be mixed back in with the processed signal.

The 3 band EQ is an inductor based LCR design. After Dannysound tryed out various EQ topologies, this was the design that sounded the nicest. When overdriven it gives a nice "bite" to the sound, and it has a certain characterful charm that's hard to put into words. The controls have a response that are subtle to begin with and get more pronounced as the controls are increased.

The Harmonic Exciter adds a little distortion to the high frequencies, which bring out the sparkle of cymbals or the snap snare drums. The operating bandwidth can be switched between Low (snare drum snap) or High (Cymbals sparkle).

There are inputs for side chaining and control with an external envelope as well as an envelope out to make the envelope detector output available to drive other modules.

It also features separate inputs and outputs for the Compressor / Expander and EQ sections, so they could be used as 2 separate modules.

Features:

Compressor/ Expander
Sub Bass Enhancer
3 Band Inductor-Based EQ
Harmonic Exciter
Envelope In/Out
Sidechain Input
Seperate In/Out for Compressor, Expander and EQ-Section
Power consumption: 85mA at +12V and 61mA at -12V

Depth: 25mm

HP : 12

Notes: Skippy is a matrix and non-matrix polyrhythmic sequencer (linear and logarithmic) which offers four completely independent tracks with a very simple interface: one button per track, one function per screen, no sub-menus.

Possible saving of 64 configurations.

Internal connection with expander module (coming soon) and with Zazou, generative composition module (coming end of 2023).

Functions per track

- BPM (10 to 400)
- Number of steps (1 to 64)
- Linear or log
- Random function
- Chaotic function
- Direction: clockwise, counterclockwise, ping-pong, pause
- Number of steps before the start of the sequence
- Number of steps before the end of the sequence
- Gate duration

Specific algorithms

- Euclidean (Bjorklund)
- Matrix Patterns
- microtiming patterns
- matrix rotation

Clock

- External clock input or Reset
- Clock output
- 1/1, 1/4, etc.

Menus

- BPM
- STEP
- BEGIN
- END
- GATES
- PROBA
- CHAOS
- WAY
- SWING
- GAUSS
- EUCLID
- TILES
- POLYR
- JAZZY
- SPIN
- PAUSE
- RESET
- SYS: save, load, new, clk/rst, clk

Tech Specs

Width: 10 HP
Depth: 32 mm

Current Draw:
+12 V 0 mA
-12 V 0 mA

Notes: Following in the tradition of Evolution and Morpheus, LINNAEUS represents yet another Dave Rossum innovation in filter technology.

LINNAEUS is a stereo state variable filter that provides the unique ability to linearly modulate its resonant frequency through zero into negative frequency, while maintaining stability. With extensive voltage control of nearly every parameter, Linnaeus lets you manipulate the filter's natural response curve in new ways, to create both subtle and dramatic timbral effects. And with a "one-knob-per-parameter" interface, LINNAEUS inspires sonic creativity that invites (and rewards) real-time interaction.

LINNAEUS's cutoff/resonant frequency is exponentially voltage controllable from sub-audio to ultrasonic frequencies, while its resonant gain (Q) is exponentially voltage controllable from 0dB to greater than 60dB.

LINNAEUS's channel output response characteristics are independently and continuously variable from Lowpass, through Bandpass, Highpass and Notch, to Low and High Shelving characteristics. Voltage control of the response characteristics are independently selectable for each of the two channels.

The linear thru-zero modulation is provided by an integrated modulation oscillator and/or an External Linear FM modulation input.

The voltage-controllable modulation oscillator can track the filter's exponential frequency or operate independently. The modulation oscillator's output waveform is continuously variable from Off through Sine, Triangle, and Sawtooth, to Square. The modulation oscillator output is summed with the external linear FM input and applied to the modulation index VCA, which controls the linear thru-zero modulation index from zero to 8X. The modulation index is, of course, also voltage controllable.

LINNAEUS features include:

- Ultra-wide frequency range, exponentially voltage-controllable from sub-audio to ultrasonic via precise 1V/OCT and attenuverted CV inputs.

- Thru-zero linear frequency modulation via an internal modulation oscillator and/or an external linear FM input.

- Variable linear modulation index, voltage-controllable via an attenuverted CV input.

- Resonance (Q) exponentially voltage-controllable from 0dB to greater than 60dB via 6dB/V and attenuverted CV inputs.

- Continuously variable response characteristics independently selectable for each of the two channels via individual Response Enable controls. Characteristics include Lowpass (12db/oct and 6db/oct), Bandpass, Highpass (12db/oct and 6db/oct), Notch, and Low and High Shelving.

- Voltage control of response characteristics via an attenuverted CV input. Individual Response CV Enable controls let you independently enable or disable CV control of response for each channel.

- An integrated modulation oscillator with continuously variable waveform from Off through Sine, Triangle, Sawtooth and Square. Its frequency can be exponentially voltage controlled via an attenuverted CV input.

- A Track control that lets the modulation oscillator precisely track the filter's exponential frequency.

- Stereo inputs and outputs. LINNAEUS can process a stereo signal or two independent mono signals. While the two channels share the filter's cutoff/resonant frequency, the filter response characteristics can be independently controlled for each channel.

- The solid, high-quality construction you expect from Rossum Electro-Music.

What's with the egg?

The functional description above describes LINNAEUS as originally conceived and designed by Dave. However, late in the beta testing process, Rossum's tester, Chris Meyer, raised the possibility of alternative behavior that would let LINNAEUS function as a self-contained (i.e., no input required) stereo oscillator and/or FM percussion voice with some really powerful timbral capabilities.

While Rossum were initially hesitant to try to shoehorn the new functions into the existing interface, once Dave had prototyped them, it was clear to us all that they were just too cool not to include. So, Rossum have provided them in the form of alternate firmware accessed by pressing and holding the Egg button.

LINNAEUS is 16HP wide and 25mm deep.

Power requirements (max): 155mA +12V, 36mA -12V. Reverse polarity protected.

Notes: ***B-STOCK: Light marks on the screen***


A serious trigger sequencer for generating complex, multi-layered rhythms. Eight channels of Euclidean pattern generation meet probability, modulation and CV control for real depth and power.

Supplier's Notes:
Constellation is all about rhythm. It is an 8 channel pattern generator that works by combining multiple dense and sparse patterns to create long, complex and musically interesting trigger and gate rhythms. Constellation takes a "parametric" approach to rhythm - there is no explicit step sequencing on the module, rather the rhythms are defined by euclidean (and more) parameters that build the rhythm mathematically.

Constellation aims to evolve the concept of euclidean rhythms far beyond the useful but repetitive patterns we often think of when we hear the term "euclidean rhythm". This is accomplished by by combining up to 8 individual euclidean patterns of different lengths and density. Each pattern may provide only a small component of the final output, but together create immensely musical and varied rhythmic material over a very long time frame - up to 999 steps! If each of those steps are 1/16 note in length at 120 bpm, that's a full 2 minutes of explicitly defined, yet non repeating rhythmic material.

In addition, Constellation's parametric approach allows any of these parameters to be modulated with CV through one of 8 freely assignable CV inputs. CV modulation introduces further ability for Constellation's rhythmic output to vary over time. Paired with a Maestro or Navigators, hours of interesting morphing rhythms are possible without the need for tons of step programming or the uncontrollable chaos of a purely generative approach.

When writing music, rhythmic interest is often built through the combination of repeating and non repeating elements that work together to anchor the overall feel but also keep the ear free from boredom over the duration of the piece. Constellation provides a unique set of tools to accomplish this goal and achieve rhythms that are intentional, unexpected and exciting to use as the foundation of your compositions.

28hp, 25mm deep
75mA +12, 18mA -12

Notes: The CubuSynth Engine V2 is their updated dual analogue VCO with wave shaping functions, internal modulations and a chaos generator. It is based around the 3340 chip and features 4 Waveforms + Wavefolder per VCO and 4 Modulated Outputs, all simultaneously.

The CubuSynth Engine can work as 2 independent VCOs, or as one complex FM oscillator.

With its internal "Chaos Engine" it creates semi-random voltages, generated by the 2 oscillator cores. This signal is then normalized to the CV inputs for Pulse width modulation and exponential FM.

Each of the 2 VCOs offers a switch to select one of the 4 waveshapes to be used by the wavefolders, and the linear FM input normalisations.

Features:

2 VCO cores (voices)
4 simultaneous wave forms per voice + 4 Modulation Outputs
Wavefolder per voice
Pulse Width modulation
Linear and exponential FM inputs
1 V/oct tracking stable over up to 10 octaves
Chaos generator with external clock input
Complex internal normalized modulations

Dimensions:
24 HP
24 mm deep

Current Draw:
87 mA +12V
74 mA -12V
15 mA 5V

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Collabing with YouTube sensation Andrew Huang, Endorphin.es offer up this impressive multipurpose processor module. Building blocks of stereo filtering, compression, reverb and more offer huge creative potential.

Supplier's Notes:
In collaboration with Andrew Huang, based on his modern music production techniques, Endorphin.es developed a creative audio processor with multiple blocks that can be moved around in order to achieve different flavours for sound design.

Processing unit without fixed structure: intuitively create astonishing and ephemeral timbres, from atmospheric rumbles to heavy or distorted textures.
Creative stereo effect processor with delay, reverb, filter and distortion with quickly explorable routing chain with single button press.
New generation ARM Cortex - M7 processor with 96 kHz 32 bit internal processing.
Lush hall and whooshing reverse reverbs with audio freeze and pre-delay.
Sidechain audio ducking envelope available both internally and externally with additional one knob single band compressor.
Tap delay with maximum delay time up to 2.5 seconds, external clock input with onboard clock divider and 1v/oct time control.
8x oversampled distortion algorithm.
Pre- and post - VCA, tone and volume controls with extra gain.

Power consumption
135 mA +12V
35 mA -12V
0 mA 5V

Dimensions
16 HP
26 mm deep with power ribbon cable connected.

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Up to eight voices of digitally synthesised drums, percussion and synth sounds from this versatile module, featuring virtual analogue models as well as FM and wavetable options.

Supplier's Notes:
Flame "Fire" percussion synth module

The module is a full 8-way polyphonic drum and percussion synthesizer. It offers different digital synthesis algorithms, which can be distributed over 8 channels. The sound engine delivers virtual analog sounds as well as different digital percussion sounds, which are generated with FM, wavetable or virtual analog synthesis. It is also possible to create sim- ple monophonic bass or synthesizer voices.

During development, particular attention was paid to direct and simple usability with regard to live operation. The hardware essentially consists of two parts (which are deli- vered together). On the one hand there is the basic module with all controls, the display, connections for MIDI, 2x CV inputs and 5 audio outputs.

There is also a separate XFIRE I/O extension with sockets for the 16 analog trigger/gate/CV inputs and 3 additional audio outputs. Both modules are connected via a 60cm long ribbon cable. In this way, the XFIRE module can be installed anywhere else in the rack. The base module is therefore only 22TE wide and can also work alone without the extension as a MIDI expander.

A maximum of 8 audio outputs are available. A stereo pair (outputs 7+8), plus 6 additio- nal individual direct outputs. All outputs are freely configurable. Two pages with settings for panorama and volume are available for the stereo main out.

There is a gate/trigger input and a configurable CV input for each channel. Two additio- nal programmable CV inputs can be used for further controls. Regardless of the analog connection, the module offers full MIDI functionality. Two MIDI inputs and a MIDI output/softthru allow integration into an external MIDI setup. The firmware can be upda- ted via MIDI Sysex. The created KIT data can also be saved or exchanged.

Notes: Evolved version of Maneco's drone synth uses an oscillator based on equations, a Korg MS20-inspired filter and built-in reverb. Check out the Grone Expander for added touch-sensitive controls.

Supplier's Notes:
Dark Drone Machine

Generates sound based on equations converted to analog signals, there are sixteen equations selected by Up and Down switches. Four LEDs indicate equation number in binary mode. Three Pots modify numbers used by the equation, A0, A1 and A2, fourth pot Sample Rate controls pitch and speed of the oscillation. There's an Output Level pot for the oscillator and a dedicated jack for patching the Oscillator sound to external modules.

NOISEGENERATOR:

White noise with noise level pot and noise output jack.

VCF:

MS20 resonant low pass filter, with CUT frequency pot control, RESONANCE, MODULATION1 amount pot, input and output jacks and second cv input for cutoff, labeled MOD2

LFO1:

Low frequency oscillator routed to MOD1 from VCF, RATE and WAVEFORM shape Pots.

Also routed to delay block1

Waveforms are: ramp up, ramp down, square, triangle, sine, sweep, random levels, random slopes

EffectsSection:

Delay with tap tempo and reverse component: controls for delay time, delay feedback, delay level and reverse component, tap tempo input jack for external control

Reverb with freeze button, controls for reverb level and reverb decay, input jack for freeze function

Notes: Osc 1 and 3 - Bytebeat oscillators

Generates sound based on equations converted to analog signals , there are sixteen equations selected by Up and Down switches. Four LEDs indicate equation number in binary mode. Three Pots modify numbers used by the equation, A0 , A1 and A2 , fourth pot Sample Rate controls pitch and speed of the oscillation. There's an Output Level pot for the oscillator and a dedicated jack for patching the Oscillator sound to external modules .

Hold toggle switches select between fast decay, long decay and hold mode, for the touch trigger input. There are CV inputs for pitch on these two oscillators

Osc 2 and 4 -Wavetable oscillators

Digital oscillators, touch controlled or gate controlled by gate jacks, pitch is controlled by pitch pot, modulation by LFO A or LFO B and cv inputs.

A0 pot selects waveform, A1 pot morphs between two waveforms.

There are individual output jacks.

LFO 1 and 2

Low frequency oscillator routed to MOD inputs for oscillators 2 and 4, also to modulation input for delay section, selectable by toggle switch , RATE and WAVEFORM shape
pots.

Dimensions
36 HP

Current Draw
200 mA +12V

Notes: Very nice old-school vocoder for Eurorack, featuring a built-in mic pre-amp and full 10-band patch bay. Internal VCO and straightforward control setup help simplify operation.

Supplier's Notes:
The VXC-2220 is an 10-band analogue vocoder with patch-bay for each individual filter section. VXC-2220 vocoder is based on the iconic classics 222 vocoder. For stand alone usage the VXC-2220 is equipped with an internal oscillator generating saw and pulse waves form C1 to C6. A simple and efficient vocoder.

Specifications

Microphone input for speech signal
Line input for speech signal
Line input for carrier signal
Input level control for speech and carrier signal
Output level control
Line output
10-Band analyzer outputs
10-Band synthesizer input
Internal VCO (1 semi-nut step size);
* Saw wave (C1 - C6)
* 3x 10% Pulse wave (C1+C2+C3 - C4+C5+C6 )
* White noise
- Synthesis for 's' and 't' sounds
- Feed-trough level control for speech and carrier channel
- Bypass switch
- 10pin power connector (+/-12V)

Dimensions:
(36HP) 128,5×182.5mm (depth: ca. 35mm incl. power connector)

Power Consumption:
+12V = 125mA
-12V = -125mA