安全购物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全购物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Synth modules

首页  Equipment  

Synth modules

Options
Items 1 to 50 of 1,007 on page 1 of 21
1  2  3  ...  21  »
Subscribe to our weekly Studio Equipment emails
MRG Synthesizer ATT Compact Passive Triple Attenuator Module
Cat: 798358 Rel: 25 Nov 20
 
Passive triple attenuator synth module
Notes: Triple Passive Attenuator Module for Eurorack Modular Synthesizers.

This is a simple module that allows to attenuate three signals independently.

A simple but very useful modules that it's always handy to have in a rack.

It is passive, thus requires no external power.
Read more
MRP:$43.03 SAVE 17%
 4 in stock $35.85
FORTHCOMING
Cosmotronic Cosmix Aural Enhancing Stereo Mixer Module
Cat: 803497 Rel: 18 Jan 21
 
Distortion/dual & stereo/mixer/dynamics/effect/panning synth module
Notes: Cosmix is an 8-channel stereo mixer with a built in analog stereo dual band maximizer.

It has four mono channels and two stereo channels, the left inputs 5 and 7 are normalised to the right inputs 6 and 8 respectively.

The four mono channels have panning- and aux send controls.

All channels are accommodated with a dedicated mute switch for live performance.

The aux output can be routed to an external effect and the four small switches below the volume faders set whether the signal that is routed to the aux bus is pre or post fader.

The master bus can optionally be fed into the stereo Drive circuit.

This circuit is true stereo, and improves almost any sound source, with full bass and amazing spatial resolution.

It works like a dual band maximizer, with separate faders for high and low frequencies.

The analog overdrive circuit can be bypassed but we don't recommend it as it sounds great and really glues the whole mix together nicely.

The overall volume can be set with the main volume knob.

The output of the compressor feeds into a diode clipping circuit, to to create a warm saturated distortion.

By playing with the levels of each channel different clipping characteristics can be achieved.

However if you prefer to keep the output signal clean, the bypass switch allows you to bypass the circuit.

The white lines indicate the non-distorted 0dB point for each channel, when the drive circuit is active and the sliders are set to zero.

Driving a channel above the white line pushes it into more overdrive and distortion, assuming 10vpp Eurorack level.

Different tones can be created by playing around with the gain staging!

Main output is eurorack level (10vpp)
Input impedance: 100k
Output impedance: 1k

70 mA +12V
70 mA -12V
0 mA 5V
20 mm deep
Read more
coming soon $265.56
Radikal Technologies RT-311 Swarm Oscillator Module
Cat: 796106 Rel: 16 Nov 20
 
Swarm oscillator module
Notes: The RT-311 can store up to 8 memory setups with 8 snapshots each, holding all oscillator settings and memorizes them even after powering down your modular synth. One highlight of this module is the opportunity to interpolate between these parameter snaphots. Interpolation can be controlled with an external control voltage or with a built in LFO. The speed of the internal LFO can be controlled with an external control voltage as well. The interpolator has even an external output to interpolate one parameter of an attached module. Both oscillators can built swarms of oscillator clones. Up to 16 Oscillators are running simultaneously at the highest setting. The detune knob changes the pitch of all oscillator clones between ultra slow oscillator frequency beating effects and multiple frequency drones and chords. The swarm can be pitched in musical intervals, chords, clusters or fat detunes. The swarm tuning can be stored into the snapshots too. That allows for to built up to 8 different chords with different sound settings one can change while playing in a setup.

Both oscillator swarms have independent outputs. If one sets the exponential FM inputs depth to maximum, the inputs run with Volt per Octave scaling. The oscillator swarms can then be used like two independent Synth voices. The scale inputs can also get quantized to musical scales. That makes it easy to control the swarm from a step sequencer. Just select the root key with the tune knob and a pentatonic scale and turn the knobs of your sequencer for always matching tonal sequences.

Electrical and mechanical Specifications:

250 mA +12V
40 mA -12V
0 mA 5V
30 mm Depth
32 HP
Read more
MRP:$860.61 SAVE 32%
 2 in stock $582.70
FORTHCOMING
Tesseract Modular Douts Direct Outs Module For Tex Mix
Cat: 800365 Rel: 28 Feb 21
 
Mixer/multiple/utility synth module
Notes: Direct Outs for TexMix & 3,5mm to 6,3mm converter.

This is a breakout box for the direct outs of the TexMix. Each module has 8 outputs so it could have 2 '4MonoChannels' connected or 1 '4StereoChannels'.

Without connecting the ribbon cable it's a 3,5/6,3 adapter.

The orientation of the 8 pin ribbon cable is marked by the 'DIRECT OUTS ' legend on the PCB of the channel expanders (mono or stereo) and a white line in the DOUTS input header.
Read more
MRP:$34.96 SAVE 17%
coming soon $29.13
Radikal Technologies Delta CEP A Semi-Modular Paraphonic Synthesiser Module
Cat: 796113 Rel: 16 Nov 20
 
Synth module
Notes: A semimodular synthesizer consists of 9 essential synthesis modules whose combination provides a very powerful and straight forward starting point into the world of Eurorack synthesizers. Let's see, which modules are included in Radikal's latest brainchild: The system includes one swarm oscillator, a mixing stage with a noise source, a very powerful filtering section around the analog multimode filter plus stereo digital emulations of 12dB multimode and 24 dB ladder filters and one VCA. One LFO and one snappy envelope generator for modulation purposes plus the secret weapon of all Radikal Technologies digital modules, the SNAPSHOT INTERPOLATOR are adding extra excitement to your sonic adventures. The icing on the cake of the sound engine is a digital FX section with incredible modulated stereo delay effects including tape delay, phasing, chorus, flanging etc.!

In a modular synth system, the different sound generating and altering sections are not connected. The user has to establish all the connections that are necessary to generate sound effects and tones with patch cables. In a semimodular synth the most essential connections are hardwired. This means you can play the DELTA CEP A right out of the box. Of course you can go a step further and add your own module patching.

The DELTA CEP A has a MIDI interface, which is essential when you want to use the paraphonic mode of the Synth. The paraphonic mode let's you play chords and turns the DELTA into the perfect pad and ensemble section. The MIDI Interface has additional outputs for external modules and a special digital bus allows for controlling the SWARM OSCILLATOR RT-311 direct with notes and chords to layer additional voices in monophonic and chords mode using an external MIDI keyboard.

The SNAPSHOT INTERPOLATOR is a very unique feature in the synthesizer world. First you have the ability to store snapshots of your sound creations into the internal memory. Then you can play these snapshots sequentially for very cool sonic sequences. But that is not all. You can even create smooth transitions from one snapshot to the other for stunning sound morphing effects. Independent from the Interpolator, the snapshot memories can also be used as preset memories and are filled with sounds from our sound designers.

23 knobs, 14 buttons, 28 RGB LEDs, 14 outputs and 17 inputs - the DELTA CEP A has a great synthesis potential that can even grow by adding additional modules. The connectivity provides the freedom to use it as part of your existing Eurorack system or as an independent solo synthesizer with our special DELTA CEP A desktop case.
Read more
MRP:$1,085.17 SAVE 20%
 2 in stock $867.32
FORTHCOMING
AniModule AnVilope Module
AniModule AnVilope Module (clock generator / envelope generator / LFO synth module)
Cat: 794381 Rel: 31 Dec 20
 
Envelope generator module
Notes: A Simple, Affordable, 4HP, Analog Envelope Generator.

Attack, Decay, Release... Simple.

- Envelope Out 0V to +7V
- Loop function so you can use it as a Variable Wave-Shape LFO / Timer
- Inverted out that goes from +7V to 0V

Function:
When the gate is High the envelope will rise and cycle through it's phases.
When gate goes low again the envelope will revert to the release phase.

If the Gate is longer than the ADR phases, the decay will play out then go to release and the envelope will end after the release.

Sprinkle them all over your system!

4HP Depth : 28mm
Read more
MRP:$115.64 SAVE 17%
coming soon $96.36
MRG ADSR Compact Envelope Generator Module
MRG ADSR Compact Envelope Generator Module (envelope generator synth module)
Cat: 798361 Rel: 25 Nov 20
 
Compact ADSR envelope generator module
Notes: Simple, compact envelope generator at a nice price. Capable of ultra-fast envelopes as well as long, slow slopes with attack up to five seconds and decay/release up to eight seconds each.

Supplier's Notes:
This is a classic envelope generator, based on AS3310, a clone of the CEM3310. Features a separate trigger input, normal and inverse envelope output, high quality components and careful engineering.

When the TRIGGER input is unconnected, rising and falling edges of the GATE input will trigger a classic ADSR envelope.

If the TRIGGER input is connected, a high GATE level will bring the output to SUSTAIN level, and the GATE falling edge will start the release phase. A TRIGGER input when GATE is high will start an attack/decay cycle. Attack, Decay and Release times vary exponentially with the control knob. For each of these parameters, the ratio between the longest possible time and the shortest is slightly more than 3000:1.

The panel is a 1.6mm FR4 PCB, matte black.

Lead-free PCBs, components and solder.

This is the second version of the MRG ADSR. The previous one is sold out. Although the module has been completely redesigned, the only visible change from the previous module is the knob orientation.

Technical details
Width: 4HP (2cm).
Depth: 4cm (can be used in skiffs).

Attack time range: 1.75msec to 5s.
Decay time range: 2.4msec to 8s.
Release time range: 2.4msec to 8s.

Attack level: 5 V
Sustain level:0 to 5V
Inverse envelope: 0 to -5V
Read more
 4 in stock $84.03
Click for better price!
or call +44 20 7424 1960
quote 798361
FORTHCOMING
Patching Panda Moon Phase Stereo Multimode Filter Module
Cat: 804366 Rel: 25 Jan 21
 
Stereo multimode filter module
Notes: Stereo 12dB/octave state-variable multimode filter with powerful imaging technique to enhance and alter the stereo field.

The resonance sounds beyond any other filter when you play with the stereo imager control.

With 8 different combinations and span to separate both filters, you increase the possibilities to treat your sounds and open them in the stereo field.

Applying audio rate cv to the stereo imager or span control input and sweeping the cutoff control will create a unique character to the filter.

The resonant peaks can be shifted around the stereo field, every cv input can be modulated up to audio rate frequencies creating a wide palette of sonic combinations.

Size: 14HP

Power consumption 82mA@+12V, 63mA@-12V
Read more
MRP:$325.42 SAVE 17%
coming soon $271.17
FORTHCOMING
Patching Panda Vibrazum V2 Triple Multimode VCF Module
Cat: 804368 Rel: 25 Jan 21
 
Triple multimode VCF module
Notes: Versatile triple multimode VCF capable of subtle to extreme tone shaping without losing the performance availability.

The three channels have dedicated outputs, as well as a mix output.

Multiple combinations of frequencies drawings are possible.

It was designed to create a movement to the sound thanks to the individual frequencies voltage control inputs.

Each channel is able to sweep through all the frequency spectrum.

A dedicated shift control with attenuverter cv input is able to swap all 3 filtres at the same time.

The Vibrazum shines at high feedback with 24dB slope, the resonance is well compensated and performative, even taking it to the extreme will not go out of control.

It sounds very “creamy” and full of rich harmonics from a gnarly tone-­shaping tool of sonic destruction, vowel robotic sounds, acid basslines, resonant percussive sounds and more…

Simple layout without compromising the wide range of sonic possibilities.

Specs:

Width: 14hp
Depth: Skiff-friendly
Current draw: +12V: <65mA, -12V: <68 mA
Read more
MRP:$333.49 SAVE 17%
coming soon $277.90
FORTHCOMING
Patching Panda Copycat Buffered Mult Module (with bicoloured LEDs)
Cat: 804381 Rel: 25 Jan 21
 
Dual-buffered mult module
Notes: 2hp dual Buffered Mult features 2 channels of 3 outputs or 1 channel of 6 outputs if nothing is connected to the second input, it has 2 bi-colour led showing positive and negative voltage.

2hp buffered mult

DC coupled

2 inputs

Bi-colour led showing positive (green) and negative (red) voltages

Power consumption 20mA@+12V, 28mA@-12V

Skiff friendly

(This is not a precision buffered multi)
Read more
MRP:$95.47 SAVE 17%
coming soon $79.55
FORTHCOMING
AniModule TikTok Module
AniModule TikTok Module (clock modulator synth module)
Cat: 793800 Rel: 31 Dec 20
 
Clock divider & multiplier module
Notes: The TikTok is a 4HP Clock Divider/Multiplier.
It has Divisions and Multiplications of:
*//2
*//3
*//4
*//5
*//6

There is a Clk Input and a Reset Input.
Both are buffered with an opamp based comparator circuit.
They are looking for approximately +1.1V on a rising edge.
This means that you are not constrained to gate (pulse) signals to trigger them.

The Reset input resets your divisions clock counter to 1

There is a switch to select Mathematical or Musical divisions.

The Multiplication Outputs 25MS Trigger pulses.
The Division Outputs are on as long as your Clock source.

Avg Current draw:
40 mA
-9 mA
Peak Current Draw:
80 mA
-17 mA

Width = 4HP
Depth = 38mm
Read more
MRP:$197.67 SAVE 17%
coming soon $164.71
MRG Synthesizer 3360 VCA Dual Linear Compact VCA Module
Cat: 798351 Rel: 25 Nov 20
 
Dual linear compact VCA module
Notes: This is a Dual Linear Low Noise VCA module, based on the AS3360.

Both VCAs can be controlled by a CV entry, modulated by control knob.

VCA1 also has an initial gain control (B1), that offsets the CV input by a constant value. This allows VCA1 to be left always open, with the initial gain controlling the amplification.

If both input jacks are used (IN1, IN2), the two VCAs will operate independently. The output of VCA1 will go to OUT1, the output of VCA2 will go to OUT2.

If there's no jack in IN2, the two VCAs will be cascaded, and the output of VCA1 will go both to OUT1 and as an input to VCA2.

This allows this module to be used to process both the MIDI Velocity and the envelope of an audio signal.

Inputs:

IN1: Input Signal for VCA1.
CV1: Control Voltage for VCA1's amplification.
IN2: Input Signal for VCA2. If no IN2 is present, the input of VCA2 will be the output of VCA1.
CV2: Control Voltage for VCA2's amplification.
Outputs:

OUT1: Output of VCA1
OUT2: Output of VCA2
Controls:

M1: Attenuator for CV1
B1: Initial gain of VCA1
M2: Attuenator for CV2

40 mm deep
Read more
MRP:$100.85 SAVE 17%
 2 in stock $84.03
FORTHCOMING
Livestock Electronics Leap ADSR & LFO Module
Livestock Electronics Leap ADSR & LFO Module (CV modulation/drum/dual & stereo/envelope generator/LFO/random synth module)
Cat: 802753 Rel: 18 Jan 21
 
ADSR/LFO module
Notes: Ever need to apply DC offset or attenuation to your modulation sources?

Want to create complex modulations using an ADSR and LFO? Need a heat packing modulation source in a small package? Jump right in and feel the Leap!

Leap is an ADSR and LFO with built in DC offset and Attenuversion. The envelope and lfo are to be used individually, however the lfo's frequency and amplitude can be modulated internally by the adsr to create a complex modulation source or a simple drum.

The envelope stages can be modulated, with attenuversion for the cv inputs.

And the lfo responds to V/oct (+-5V) or can be synced to a clock.

Width: 10HP

Depth Back 25MM

Depth Front 25MM

Weight 133g

Power @ +12V 110mA

Power @ -12V 30mA
Read more
MRP:$235.32 SAVE 20%
coming soon $188.24
FORTHCOMING
Livestock Electronics MIR Quad VCA Module
Livestock Electronics MIR Quad VCA Module (attenuator/distortion/logic/mixer/polariser/quad/utility/VCA synth module)
Cat: 802754 Rel: 18 Jan 21
 
Quad VCA module
Notes: Need an attenuator, sub-mixer, linear or exponential vca, distortion or clipper, voltage or phase inverter and a logic gate? Yes of course you do... MIR provides you all of that, times four!

MIR is a multifunctional tool that can be utilised in many patch situations. Each channel is equipped with three inputs, this allows you to mix signals and control the amplitude of that mix simultaneously.

The gain knob can be used as an attenuator, or distortion when cranked up high.

MIR clips at +-5V so you can also use it as a logic gate, just insert gates into the inputs and why not combine them with other signals?

Two outputs per channel allow for normal and inverted signal outputs. Certainly fun for experimentation with crosspatching and distribution of signals!

Width: 10HP

Depth (Back): 25MM

Depth (Front): 25MM

Weight: 133g

Max @ +12V: 80mA

Max @ -12V: 75mA
Read more
MRP:$235.32 SAVE 20%
coming soon $188.24
FORTHCOMING
Tesseract Modular Tex Mix 4 Mono Channels Expandable Mixer Module
Cat: 797284 Rel: 31 Jan 21
 
Synth module
Notes: This is a 4 mono channels expansion. Several of these modules can be added to provide more channels. Every channel features:
- Mono input
- Vactrol Gate (plug a CV into the GATE IN to modulate the volume of a channel, just like a classic VCA. When nothing is plugged in the GATE IN, the gate is normalled to fully open)
-SEND A control (switchable PRE/POST, in PRE mode the signal is present regardless to the channel volume control but only if the channel switch is in ON position)
-SEND B control (post-fader)
-PAN control (only affects the master bus)
-VOLUME control (affects the master, cue and POST sends, does not affect PRE-fader send)
-ON/OFF/CUE switch: ON - channel is routed to the master bus
OFF - channel is muted
CUE - channel is routed to the cue bus

13 mA +12V
8 mA -12V
Read more
MRP:$96.82 SAVE 17%
coming soon $80.67
FORTHCOMING
Livestock Electronics Felix Buff Mult Module
Livestock Electronics Felix Buff Mult Module (attenuator/controller/dual & stereo/multiple/polariser/utility synth module)
Cat: 802751 Rel: 18 Jan 21
 
Buffered multiple module
Notes: What if you could use one modulation source and adjust it for multiple parameters, create a bus to send audio sources to effects, or even create a macro controller?! A certain cat has got your back!

Felix is a 1:6 or 2x1:3 buffered multiple with an attenuator or attenuverter per output. It is great for distributing a source to different parameters and controlling the gain and/or direction for a specific parameter.

But it can also be used for audio, which makes it great for creating auxiliary busses.

Finally when no source is given the module can be used as a stable voltage distributor. Really useful for creating DC offsets or macro controls!

Width: 6HP

Depth (Back): 20MM

Depth (Front): 15MM

Weight: 65g

Max @ +12V: 32mA

Max @ -12V: 30mA
Read more
MRP:$116.99 SAVE 21%
coming soon $93.00
FORTHCOMING
Livestock Electronics Bang Wavetable Oscillator Module
Livestock Electronics Bang Wavetable Oscillator Module (digital/noise/oscillator/waveshaper synth module)
Cat: 802749 Rel: 18 Jan 21
 
Wavetable oscillator module
Notes: Want to create your own wavetables? Generate tons of interesting lo-fi waves that excel in percussive sounds? Or just want an oscillator that can produce rich harmonic textures? This may be a Bang for your buck!

Bang is a lo-fi digital wavetable oscillator inspired by old game consoles. However it takes a totally new approach to wavetable synthesis: within a cycle it switches between socalled chunks that are indexed as odd or even numbers. Waves can be assigned to these odd or even chunks, which allows for complex waveforms. The result is aliased, rich and absolute fun!

The module comes with six libraries containing 12 waves each. And user wave libraries can even be created using the supporting application for Mac and Windows.

Width: 10HP

Depth (Back): 30MM

Depth (Front): 25MM

Weight: 133g

Max @ +12V: 75mA

Max @ -12V: 30mA
Read more
MRP:$329.45 SAVE 20%
coming soon $264.45
FORTHCOMING
Livestock Electronics Ellis Macro Controller Module
Livestock Electronics Ellis Macro Controller Module (controller/digital/sequencer synth module)
Cat: 802750 Rel: 18 Jan 21
 
Controller module
Notes: Do you want to gradually fade between sounds in a live set? Create chords of up to 8 voices? Or be able to retrieve settings on a module without presets? Ellis is the preset maker for cv inputs!

Ellis is a controller module that allows you to create presets for cv inputs on your other modules. It has been designed to easily go from one preset to another by turning the fade knob or by automating it entirely. Preset selection, morphing and fading can all be modulated with CV, which will ease your way into that next track!

The outputs are V/oct (+-5V), and can be transposed using the trans input. While the trig output sends out a gate or trigger when a preset is changed. This is what makes Ellis great as a chord creator too!

Width: 12HP

Depth Back: 25MM

Depth Front: 25MM

Weight: 133g

Power @ +12V: 160mA

Power @ -12V: 40mA
Read more
MRP:$305.25 SAVE 20%
coming soon $245.39
FORTHCOMING
Livestock Electronics Maze Matrix Mixer Module
Livestock Electronics Maze Matrix Mixer Module (mixer/multiple/quad/switch/attenuator/polariser/sequencer/controller synth module)
Cat: 802755 Rel: 18 Jan 21
 
Preset morphing & router matrix module
Notes: Want to change your patch with a push of a button? Create presets for attenuversion, routing and mixes of signals? Sequence and morph through audio and cv? Then Maze has got you sorted!

Maze is a versatile routing and mixing matrix. That allows you to create your own touchpad of patch presets. Each routing position has been equipped with an attenuverting VCA so it can be used for signal distribution and attenuversion.

Morphing speed between presets can be changed and routings can be muted. Preset selection is alsopossible with CV and several algorithms.

The signal path is entirely analog and it is even possible to chain Maze modules together to increase your matrix.

Width: 12HP

Depth (Back): 43MM

Depth (Front): 25MM

Weight: 165g

Max @ +12V: 200mA

Max @ -12V: 70mA
Read more
MRP:$470.65 SAVE 20%
coming soon $377.63
FORTHCOMING
Tesseract Modular Radioactive Analogue Modelling Digital Oscillator Module
Tesseract Modular Radioactive Analogue Modelling Digital Oscillator Module (digital / oscillator / waveshaper synth module)
Cat: 797271 Rel: 31 Jan 21
 
Synth module
Notes: Analog modelling digital oscillator with phase offset modulation

Radioactive is a small but powerful 14-bit analog modelling voltage-controlled digital sound source: a complete voice Eurorack module in 6HP. It consists of 3 simultaneous independent oscillators, voltage-controlled AR/ASR transient generator, voltage-controlled pitch slew (glide) and voltage-controlled waveshaper with 5 different modes, but that's just the beginning. Its forte consists of selectable gate/trigger/constant envelope timing signals, rather unique 3-voice polyphonic mode, semitone-quantized mode, voltage-controlled waveform selection, on-the-fly selectable 10Vpp CV input range with offset (except for Pitch), a few experimental features, and then some.

Under the hood, it's a chiptune-inspired wavetable-gnawing sound cruncher with a mind of it's own, and oh boy it's dirty. It could be described as raw and untamed, but it would probably be an understatement.

Operation:
V/Oct Pitch input with attenuator
3 CV inputs with offset (Glide/Attack, Release, Shaper)
Trig/Gate input for envelope triggering/gating
Wave change trigger input
Single button with 3 different functions: waveform change with short press, shift function (alternate control parameter) with long press, enter setup mode on power-up.
3 green illuminated indicators of selected waveform and their combinations, also providing information in setup mode
Single red illuminated indicator of incoming trigger or high/low gate signal
Simple and intuitive setup without menu diving (parameters are saved and recalled at start-up)
3 different operation modes (A, B & C) selectable in setup:
A - Free range oscillator with Attack and Release envelope
B - Free range oscillator with Release envelope and Glide
C - Quantized oscillator with Release envelope and Glide
3 different envelope activation modes (G, T & P) selectable in setup:
G - Gate mode, monophonic
T - Trigger mode, monophonic
P - Poly mode, 3-voice polyphonic
5 different wave shaper modes selectable in setup and at runtime
9 basic waveforms and 12 different combinations

Specifications:
VCDO sound source with thousands of possible waveform shapes
All inputs: 100k impedance, 512Hz DC rate
32kHz refresh rate
14-bit sound generation
10-bit CV capture
V/oct input range: 0 to +5V (C1-C6 with octave shift control to cover the entire C0-C8 range)
CV input range: on-the-fly selectable 0 to 10V, -5 to +5V or any other 10Vpp range between -10 and +10V
Trig/Gate input range: 0 to +10V (0V closed, 3V+ open), protected
Output levels: -5V to +5V (10Vpp), envelope/shaper mode dependable
Professionally designed front panel with all linked functions clearly labeled in different colours
Comprehensive User guide covering all operation modes and extensive Build guide for DIYers

42 mA +12V
10 mA -12V
0 mA 5V
25 mm deep
Read more
MRP:$103.54 SAVE 17%
coming soon $86.28
FORTHCOMING
Tesseract Modular FranKinksTides 1.2 Dual Tidal Modulator Module
Tesseract Modular FranKinksTides 1.2 Dual Tidal Modulator Module (envelope generator / function generator / LFO / oscillator / digital / dual & stereo synth module)
Cat: 797277 Rel: 31 Jan 21
 
Synth module
Notes: Dual tidal modulator with max, min & mix outs

FranKinksTides is a 18hp dual Tides (based on the Swirls pcb layout) with the max/min circuit from Kinks and some switches for sync, quadrature, pll and fm operation . It can be a double/complex oscillator, a dual function generator or any combination of oscillator, Lfo and Envelope generator with lots of cv control plus some interesting cross-modulation and sync features.

Some improvements in version 1.2:

-Mix output is now buffered, no signal bleeding on single outs.
-Mix pot controls also the balance of the signals sent to the max/min circuit.
-Uni/bi switch now also determines the signal sent to FM1.
-Clock/sync switch has now a center OFF position, no need of plugging a dummy cable in the Clock1 when using Sheeps firmware to avoid ultra fast sound bank changes.
small improvements for DIY:
-Bigger font size on the pcb.
-Parts renumbered for easy DIY.

Original design by Emilie Gillet
Available assembled and DIY (pcb+panel)
+12v
-12v
Read more
MRP:$264.91 SAVE 17%
coming soon $220.75
FORTHCOMING
Tesseract Modular Nutella Tsunami Conversion Module
Tesseract Modular Nutella Tsunami Conversion Module (drum / MIDI / sampling synth module)
Cat: 797279 Rel: 31 Jan 21
 
Synth module
Notes: Nutella is a eurorack conversion module for the Sparkfun Tsunami Super Wav Trigger.

30 mA +12V
15 mA -12V
200 mA 5V
Read more
MRP:$313.32 SAVE 18%
coming soon $256.61
FORTHCOMING
Tesseract Modular 12x12 Buffered Matrix Module
Tesseract Modular 12x12 Buffered Matrix Module (multiple / utility synth module)
Cat: 797270 Rel: 31 Jan 21
 
Synth module
Notes: This module is a 12 ins and 12 outs precision buffered matrix.

Is conceived to be a semi-permanent matrix for medium to big systems, with white silkscreen labels to customize ins and outs names.

Every output has a rotary switch to select an input. You can make the same input go through several outputs but not several inputs go to the same output.

There's also a bicolor led next to every output for visual info of the signal that is going through it.

Allows fast patch changes and easy rerouting signals, both audio and cv.

Can be used as a traditional buffered multiple, pretty flexible one: 1 x 12 outs, 2 x 6 outs, 3 x 4 outs etc.

26 HP
45 mA +12V
45 mA -12V
Read more
MRP:$240.70 SAVE 17%
coming soon $200.58
FORTHCOMING
Tesseract Modular 8x8 Buffered Matrix Module
Tesseract Modular 8x8 Buffered Matrix Module (multiple / switch / utility synth module)
Cat: 797244 Rel: 31 Jan 21
 
Synth module
Notes: This module is a 8 ins and 8 outs precision buffered matrix.

Every output has a rotary switch to select an input. You can make the same input go through several outputs but not several inputs go to the same output.

There's also a bicolor led next to every switch for visual info of the signal that is going thru it.

Allows fast patch changes and easy rerouting signals, both audio and cv.

Can be used as a traditional buffered multiple, pretty flexible one: 1 x 8 outs, 2 x 4 outs, 4 x 2 outs or any other combination.

62 mA +12V
65 mA -12V
Read more
MRP:$114.30 SAVE 17%
coming soon $95.25
FORTHCOMING
Tesseract Modular Selecta 8-Channel OR Combiner & A/B Switch Module
Cat: 797261 Rel: 31 Jan 21
 
Synth module
Notes: This module has 4 channels of OR Combiner and 4 channels of A/B Switch.

This new version has a reversible panel, so the switches can be placed on the left or the right side.

The OR Combiner is conceived to select or sum trigger and/or gate signals, each channel has 2 inputs (A & B) and one output. A switch select which signal would be present at output, being the middle position of the switch the sum of both. It could be used with other type of signals but only the positive part of these would be present at the output stage (with a small lack of voltage because of the diodes and the pulldown resistor), so it could work with envelopes for example. With bipolar voltages the OR COMBINER channels will work as a Half-wave rectified output (the negative half of the signal is clipped to 0V) This can add many harmonics to audio signals, the combination of 2 oscillators will give as result a sort of 'ring modulator' sound.

The A/B Switch selects between A and B and the middle position of the switch is a "mute", works with any kind of signal (cv or audio) and is bidirectional. Can be used with 2 input signals and 1 output or 1 input signal and 2 outputs.

The circuit of the first version has been re-designed to avoid the bleeding among other issues.

This module does not draw any power.

Read more
MRP:$67.24 SAVE 17%
coming soon $56.02
FORTHCOMING
Tesseract Modular Step Fader Dual Sequencer Module
Tesseract Modular Step Fader Dual Sequencer Module (sequencer / slew limiter / CV modulation / dual & stereo synth module)
Cat: 797267 Rel: 31 Jan 21
 
Synth module
Notes: This is a dual sequencer, nothing really new but fun to play with. Oriented to facilitate the interaction of both sequencers in order to get more complex patterns and polyrhythms. Very "hands on" CV source & good complement for more complex digital sequencers like Eloquencer, Performer etc.

There are 3 GLOBAL STYLES:
DUAL (2 totally independent 8 step sequencers)
PARALLEL (one sequencer with 2 rows of CV and 8 steps)
SINGLE (one sequencer with 16 steps)
There are also those PLAY MODES:
Normal
Reverse
Pendulum
Random

There are 2 dedicated buttons (and trigger inputs) to change the sequencer behaviour, pressing 1 button will cycle between the play modes, pressing 2 buttons will do it within the global styles.

Each sequencer has:
8 faders & 8 switches (1 per step)
1 master fader
1 switch for manual step & reset
clock, reset and mode inputs
2 gate outs (activated with the switches, center position is no gate)
1 cv out (0 +8 volts range, unquantized)

There is also an output which is the sum of the 2 CVs of both sequencers and 2 gate outs which are a combination of both sequencer gate lines, pretty handy if it's being used as a 16 steps single sequencer but also interesting when used in dual style.

8 position rotary switch to control the number of steps of the second sequencer, but also other switch allows to send that "reset" signal to the first sequencer instead of the second one, useful for the single 16 step style or to make both sequencers interact.

It has 2 slew limiter circuits with input and output, so they can be used independently, by default processing the CV out of each sequencer, forcing the slew to the max will give as result like a weird-synched LFO, but also the gate outs could be plugged in to get like rudimentary envelopes.

The first sequencer has CV control over step repetition, there's a switch to select the CV IN or the second sequencer as source for such purpose (the master fader has no effect over this, so the 8 lines of the faders correspond to the step repetition, from 1 clock per step to 8) Than means that when used in parallel style the lower row of faders could control the step duration, Metropolis or System 100m style.

Two jumper in the back of the module allows to use the "mode 2" input as reversed CV sum output, giving a total of 6 CV and 6 GATE outs.

26 HP
53 mA +12V
14 mA -12V
Read more
MRP:$216.50 SAVE 17%
coming soon $180.41
FORTHCOMING
Transient Modules u2X Dual Buffered Multiple Module
MRP:$53.79 SAVE 13%
coming soon $47.05
FORTHCOMING
Transient Modules u3A Three Channel Attenuverter Module
MRP:$88.75 SAVE 13%
coming soon $77.31
FORTHCOMING
Sound Force VCF/VCA 6 Module
Cat: 804304 Rel: 25 Jan 21
MRP:$316.00 SAVE 19%
coming soon $255.48
FORTHCOMING
Transient Modules 1F Voltage Controlled Switch Module
MRP:$104.89 SAVE 15%
coming soon $89.64
FORTHCOMING
Tesseract Modular Sweet Sixteen Mk2 Module
Tesseract Modular Sweet Sixteen Mk2 Module (attenuater / controller / MIDI synth module)
Cat: 797258 Rel: 31 Jan 21
 
Synth module
Notes: This module is a eurorack version of the 16n Faderbank, implemented with 16 CV inputs and some other smart add ons. Almost everything is in the front panel.

This new version is oriented for firmware tweaks and future expansions, still being fully compatible with the 16n and the previous Sweet Sixteen.

Changes from previous versions:

Function push button
Function led
Expansion header in the back
i2C pull-up switchable with jumpers (aux pcb not required)
Mate black & gold panel with brass nuts

There are 16 channels, which can be used as:
Midi controller
Manual CV generator (0 to 8v range)
Attenuator
CV to Midi CC
i2C controller
CV to i2C data

The Midi CC number and channels can be different for the TRS jack and the USB port. The firmware has been tweaked to allow also Pitch Bend, which is pretty handy because you can get much better resolution through Midi (from min to max values Midi CCs have 128 steps and Pitch Bend has a resolution of 16.384 steps).

The voltage generated by every fader is up to 8v, which is good enough to control eurorack modules (like wide open/close the cutoff frequency of a filter etc).

In the midi CC messages, 0 volts will correspond to a value of 0, and 8 volts to a value of 127. But the CV to Midi can handle also negative voltages, for such task there are 4 slide switches (1 for every 4 faders) that swaps the internal voltage reference in a way that, when activated, 0 volts will be the middle position of the midi controller, -4 volts the minimum value and +4 volts the maximum. Those switches only affect the Midi/i2C outs, CV outs won't be affected by them in any way.

If you plug in a bigger voltage source (like a -5v+5v LFO or a 10v envelope) the fader will work as attenuator, so you'll be able to adapt how that signal affects the Midi CC out, covering the whole Midi CC range, saturating the waveform or just affecting it briefly.

Panel USB port is type B, which seems to be stronger than mini or micro ones.

i2C could connect directly to an ER-301, monome Ansible or a monome Teletype.

The Teensy can be powered via the internal regulator or the +5v eurorack rail (selectable via a switch on the back).

The partial kit comes with all SMD populated, so only through hole components requires soldering work.

size: 24 HP

92 mA +12V

86 mA -12V
Read more
MRP:$204.39 SAVE 17%
coming soon $170.32
FORTHCOMING
Sound Force DCO Oscillator Module
Cat: 804293 Rel: 25 Jan 21
 
Oscillator module
Notes: The SoundForce DCO is an oscillator for Eurorack based on the architecture of the Juno-60/106 oscillator section. It is a modern homage to that sound using technology from the future. It provides true analog waveforms with digital stability.

A DCO is not an all-analog VCO but also not a digital oscillator. It's an hybrid design that combines the best of both. Similarly to many VCO's, the DCO generates its core waveform, the saw wave, by charging a capacitor in an op-amp integrator configuration. A VCO will restart the waveform cycle when the signal has reached its maximum amplitude. But the DCO starts an new cycle when a micro-controller, a small computer chip, commands it to. The micro-controller also controls the rate at which the capacitor is charging, hence the frequency of the oscillator. As with a digital oscillator, the DCO acquires the CV input voltages and turns them into numbers that will later set the frequency of the oscillator. This is done inside the micro-controller using 16 bits sigma-delta analog to digital converters. All signals are true analog signals. The PULSE wave is derived from the SAW wave using a comparator and the SUB oscillators are generated using a flip-flop IC. Furthermore, the use of a very modern micro-controller with built-in 32 bits timers have improved the frequency accuracy a lot compared to the original design.

The SoundForce DCO features 10 slide pots (faders) reminiscent of the Roland synths. 5 sound sources are available: SAW, PULSE, SUB1 (1 octave lower), SUB2 (2 octaves lower) and NOISE. The built-in mixer allows you to mix them together using the faders and the MIX output jack. The PULSE has manual pulse width control, as well as PWM with a CV input and an attenuator. An FM input is also available with an attenuator. The oscillator can be hard synced to another oscillator using the SYNC input.

Specifications:
16HP
Frequency range : 20Hz - 14kHz
Depth: 38mm (including power connector)
Power: +12V 82mA, -12V 26mA
V/OCT input range -3 to 7V
FM input range -5V to 5V
PWM input range -5V to 5V
Read more
MRP:$268.94 SAVE 20%
coming soon $216.27
FORTHCOMING
Transient Modules 2M Dual Three Channel Mixer Module
MRP:$153.30 SAVE 14%
coming soon $131.09
FORTHCOMING
Transient Modules 4R Quad Random Voltage Generator Module
MRP:$116.99 SAVE 15%
coming soon $99.72
FORTHCOMING
Transient Modules 7J Compact Joystick Module
Cat: 804248 Rel: 25 Jan 21
MRP:$188.26 SAVE 14%
coming soon $162.48
FORTHCOMING
Transient Modules 8S 8 Step Sequencer Module
Cat: 804251 Rel: 25 Jan 21
MRP:$176.16 SAVE 15%
coming soon $150.15
FORTHCOMING
AniModule Line_Amp Module
AniModule Line_Amp Module (multiple / preamp / utility / dual stereo / external synth module)
Cat: 793793 Rel: 31 Dec 20
 
Buffered multiple module
Notes: Check out AniModule's Line to Synth Level Converter.

2 Channels of 1 in <--> 2 Out.

Each channel is designed to multiply your input by *3 to boost your Line Gear / Tablet / Phone so you can integrate audio OR Control Voltages from your auxiliary systems.

Each channel's input is designed with Line Level gear's input impedance in mind.

Perfectly compatible with Synth Output Impedances, but the standard Synth Input Impedance is higher than Line level equipment is expecting.

Don't need to amplify your XPhone right this minute? Never fear! Just Hit the Switch!

This module won't sit unused in your cabinet breeding resentment and dust bunnies.

Hit the switch and that channel becomes a normal 2 HP Unity Gain Buffered Mult.

Only need one channel of each? It's YOUR Choice!
Read more
MRP:$111.61 SAVE 17%
coming soon $93.00
FORTHCOMING
Mordax Data Multifunction Tool Signal Analyser & Generator Module (white)
Notes: The Ultimate Eurorack Utility Module (and a whole lot more!)

The DATA is a digital platform for testing, measurement, and signal generation in Eurorack modular synthesis systems. It is a modular tool kit, with functions applicable to any system and style.

Use the DATA's scope to view the interactions between your control voltages and audio signals, allowing you to master your modules by understanding their voltage ranges, control shapes, and parameter responses. Use the DATA's dual waveform generator to dial in a precisely scaled LFO for CV control, or use the waveform's frequency "note mode" to effortlessly make dyads (two note chords). Use the DATA's clock program as a master clock or to divide or multiply an incoming clock signal, sending four different clock outs to gate modules directly or as control to sequencers.

The possibilities of the DATA are basically unlimited; with the included microSD you can update the DATA's firmware and we can continue to refine and create new programs.
Read more
MRP:$564.77 SAVE 21%
coming soon $447.11
FORTHCOMING
Acid Rain Technology Chainsaw Digital Oscillator Module
coming soon $256.61
FORTHCOMING
Acid Rain Technology Maestro 6 Channel Clocked Modulation Module
coming soon $367.55
FORTHCOMING
Acid Rain Technology Navigator Voltage Utility Module (fully assembled)
coming soon $85.16
FORTHCOMING
Acid Rain Technology Switchblade 3 Channel Switch & Mixer Module
coming soon $112.05
FORTHCOMING
AniModule XXX_OR Module
AniModule XXX_OR Module (clock modulator / CV modulation / logic / ring modulator synth module)
Cat: 794039 Rel: 31 Dec 20
 
XOR module with analogue & digital outputs
Notes: A Triple Analog XOR module with an Analog and a Digital (Gate) Output.

You can use the Gate Output for your normal Boolean XOR functions (feel free to input Analog signals.)

But the real magic happens at the Analog Output.

-Take 2 waveforms and feed 1 to A and 1 to B
-When 1 signal is low the other is normal
-When 1 signal is high the other is inverted

It's not just on and off like a digital XOR- you get all the varied nuances of a tri, sine or saw wave that you put in to it.

-The Analog Output of Channel 1 is normalled to Channel 2 A Input via the jack switch
-The Analog Output of Channel 1 is normalled to Channel 3 A Input

This way you can still use your Analog Out from each channel and not worry about patching the next XOR function in the chain together.

Use it for CV!
Use it for Clocking, Tempos and Rhythm manipulation!
Most of all Feed your Audio into it!

Width = 4HP Depth = 29mm

Current draw is:
+12V = +33 mA
-12V = -21 mA
Read more
MRP:$134.47 SAVE 17%
coming soon $112.05
MGR Synthesizer 3320 LPF 24dB Resonant Low Pass Compact Filter Module
Cat: 798347 Rel: 25 Nov 20
 
Low pass compact filter module
Notes: The MRG 3320 LPF is a low pass voltage controlled filter based on the AS3320 (clone of the CEM3320).

This is a compact, but powerful and high quality 24dB 4 poles resonant low pass filter.

It is a clean, low noise filter, but can reach some screamy qualities when resonance is turned to the maximum.

All parameters are both voltage and knob controlled.

The panel is a 1.6mm FR4 PCB, matte black.

Lead-free PCBs, components and solder.

Technical Details:
Width: 4HP (2cm).
Depth: 4cm (can be used in skiffs).

Audio Signals
INPUT: Input Audio Signal.
OUTPUT: Output Filtered Signal.

Control Signals
CUTOFF: CV for filter cutoff modulation.
PEAK: CV for filter peak modulation.

Controls
C: Cutoff base frequency.
P: Peak base amount.

CM: Attenuator for the CUTOFF input.
PM: Attenuator for the PEAK input.
Read more
MRP:$100.85 SAVE 17%
 2 in stock $84.03
MRG Synthesizer 3340 VCO Precision Compact VCO Module
Cat: 798345 Rel: 25 Nov 20
 
Precision compavtr VCO synth module
Notes: The MRG 3340 VCO is an oscillator based on the AS3340 (clone of the CEM3340).

Quality components, polypropylene timing capacitor, and precise tuning make this a small, simple, but high quality oscillator.

1V/Oct CV stable over more than 6 octaves, precise waves, PWM and SYNC input.

Output waves are square and sawtooth.

When no PWM input is present, the square wave has a duty cycle of 50% - this is actually configurable by an internal trimmer.

The panel is a 1.6mm FR4 PCB, matte black.

11 mA +12V
13 mA -12V
0 mA 5V
40 mm deep

Technical Details:
Width: 4HP (2cm).
Depth: 4cm (can be used in skiffs).

Frequency range: 16Hz-24kHz
Sawtooth output: +5V/-5V
Square output: +5/-5V

Inputs
CV: 1V/Oct CV input.
MOD: Exponential FM input.
SYNC: Hard Sync.
PWM: Pulse-Width Modulation Input.

Controls
M: Attenuator for the MOD input.
C: Coarse base frequency.
F: Fine base frequency.

Outputs
SAW OUT: Sawtooth output.
SQUARE OUT: Square/Pulse output.
Read more
MRP:$100.85 SAVE 17%
 2 in stock $84.03
MRG Synthesizer MULTI Compact Passive Multiple 4x2 or 2x4 Module
Cat: 798355 Rel: 25 Nov 20
 
Compact passive synth module
Notes: This is a simple module that allows to duplicate signals. Each column can be used either as a dual 1x2 multiple, or as a 1x4 multiplier, depending on the presence of a jack in slots 3 and 4.

Really simple, but incredibly useful.

This module is passive, i.e. requires no external power.
Read more
MRP:$33.62 SAVE 17%
 4 in stock $28.01
FORTHCOMING
AniModule DD Dual VCA Module
AniModule DD Dual VCA Module (CV modulation / panning / VCA / dual stereo synth module)
Cat: 794391 Rel: 31 Dec 20
 
Dual VCA module
Notes: A Dual VCA for Audio or CV.

Mod In 1 is Buffered, Inverted then Normalled to Mod In 2, to facilitate stereo panning and VC CrossFading without a bunch of support modules.

Don't want it? Just turn the attenuator down or plug a signal of your choosing in to the Mod In 2.

Current Draw: +12V = 25mA, -12V = -22mA

8HP, 28mm Deep
Read more
MRP:$207.08 SAVE 17%
coming soon $172.57
FORTHCOMING
AniModule Lil' Monster VCO Module
AniModule Lil' Monster VCO Module (oscillator synth module)
Cat: 794393 Rel: 31 Dec 20
 
VCO module
Notes: At 8HP and 28mm deep this is A Frightening little Oscillator with Monstrous PWM, Sick, Sick Sync, and Terrifying FM capabilities!!

Great 1V/Oct tracking

Range from below to above the audible

All Waveforms respond to your Sync Input signal

Current Draw: +12V = 21mA, -12V = -21mA 8HP, 29mm Deep
Read more
MRP:$251.46 SAVE 17%
coming soon $209.54
FORTHCOMING
AniModule MixMan Module
AniModule MixMan Module (attenuater / mixer/ multiple / polariser / utility synth module)
Cat: 794394 Rel: 31 Dec 20
 
Mixer multiple & CV manipulator module
Notes: This quintessential module, while seeming fairly utilitarian, is practically Indispensable.

At only 8HP wide and 30mm deep
You can Mix, Mult, Invert and Offset your Audio and CV.

For starters there is a 3 Channel Mixer with x3 Buffered Outs.
Then there is a dedicated Analog Inverter.
Last but not least there is an Offset Manipulator.

The Offset Manipulator is designed to take a signal and combine it with an offset.
It will work fine without a signal coming in to it though. Just take the signal from the Offset Manipulator out and dial in your desired voltage.

The Offset Manipulator Out is Normalled to the 3rd Mix In Jack Switch. If you don't want your Mixer Signals Offset, Connect a plug to the 3rd Mix In Jack First, or just dial down the 3rd attenuator to 0.

The Mixer Out is Normalled to the Inverter In Jack Switch. That way you can have an inverted version of your MixOut at the Inverter Out without using an extra patch cable
Read more
MRP:$133.13 SAVE 17%
coming soon $110.92
FORTHCOMING
AniModule Quad Comparator Module
AniModule Quad Comparator Module (CV modulation / logic / comparater / utility / quad synth module)
Cat: 794399 Rel: 31 Dec 20
 
Quad comparator module
Notes: Simple quad comparator based around the LM339.

It will take your Voltages and turn them into Logic On.

When your signal is higher than the threshold the Gate goes high and the NOT Gate goes low.
When your signal is lower than the threshold the NOT gate goes high and the Gate goes low.

You can set the threshold anywhere from about -10V to +10V.

Input 1 is buffered then normalled to JackSwitches 2->4. So you could send an LFO in to Input 1, set different thresholds for all the inputs and have all the gates/NOT Gates fire at different points from the same LFO.

115 mA +12V
95 mA -12V
29 mm deep
O 5.00 (1 Votes) Average Rating
Read more
MRP:$192.29 SAVE 17%
coming soon $160.23
Items 1 to 50 of 1,007 on page 1 of 21
1  2  3  ...  21  »

Filter

Synth modules
商品
Release Date
Close