安全购物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全购物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Division 6

首页  Labels  

Division 6

Options
Items 1 to 4 of 4 on page 1 of 1
FORTHCOMING
Division 6 Business Card Sequencer V2
Cat: 777968
 
business card sequencer
Notes: The Division 6 packs a lot of sequencer into a tiny package! This 16-step circuit can work as a sequencer or as a handheld keyboard.

Specifications:
Power In: 7-15VDC, tip positive through a 3.5mm jack. Find a voltage source on your synth to power it if you can! A 9V battery or AC adapter will work too.

Power supply: 7-15VDC (reverse-polarity protected!)
Power connection: 3.5mm phone jack, center-positive
Current draw: 15ma
Dimensions: 3.5" x 2" (the same as a business card!)
Read more
MRP:$108.40 SAVE 19%
coming soon $88.14
FORTHCOMING
Division 6 Business Card Synthesizer (fully assembled)
Cat: 777973
 
business card synthesiser
Notes: The Business Card Synthesizer is a tiny synth that can be connected to a Business Card Sequencer, other synth gear, or played by itself.

Headphones can be connected directly to the output of the synth, and there are plenty of knobs to play with, so you can easily make noises anywhere. Great for learning about synthesizers!

S&H Button: Enables Sample & Hold, which disables the external CV IN jack and uses LFO1 and LFO2 to determine oscillator pitch. LFO1 sets the sample rate (SHAPE is ignored for this), and LFO2 is the wave that gets sampled.

GATE Button: Manually turns on the gate so sound comes out of the synth. This control is momentary, but you can latch it on by tapping the S&H button while holding the GATE button down.

COARSE TUNE: Adjusts the pitch of the oscillator up or down in large increments

FINE TUNE: Adjusts the pitch of the oscillator up or down in fine increments

SHAPE: Changes the shape of the wave produced by the main oscillator (VCO). Turning this control fully CW gives you a triangle wave. Start turning it CCW takes you through sawtooth/ramp, then at about the 12:00 position you get a square wave. Continue turning it CCW and you get several higher duty cycle square waves
.
GLIDE: Adjusts the rate at which the pitch of the VCO takes to go between pitches (whether changed by the COARSE TUNE knob or CV IN). Fully CCW causes the pitch to react almost instantly, while fully CW makes it take its sweet time.

LFO 1 / LFO 2 SHAPE: Changes the shape of the waves produced by the low-frequency oscillators (LFOs). The shapes are similar to those of the VCO, except that the LFOs have sawtooth/ramp waves that go both up and down (since you can actually hear the difference at LFO rates).

LFO 1 / LFO 2 RATE: Controls how fast the LFOs go.

LFO -> VCO: Routes the two LFOs to control the pitch of the main oscillator. The 12:00 position is basically "off", and the LFOs have no effect on pitch. Start turning the control CCW and LFO1 starts changing the pitch of the VCO. Maximum effect is at about 10:00. Continuing to turn the control starts to bring in LFO2 as well. All the way CCW gives you full effect from both LFO1 and LFO2.

Turning the control CW from 12:00 does essentially the same thing, but brings in LFO2 first, then LFO1.

This might seem like kind of a weird control, but it gives you quite a bit of routing flexibility with one knob. You can have no pitch modulation, LFO1, LFO2, LFO1 with a little LFO2, or LFO2 with a little LFO1.

LFO -> VCA: Routes the two LFOs to control the amplitude of the oscillator. (See LFO -> VCO control description above for more information about how the control works.)

ATTACK: Controls how fast the audio amplitude fades in when the gate is triggered. CCW is fast and CW is slow.

DECAY: Controls how fast the audio amplitude fades out when the gate is released. CCW is fast and CW is slow.

VOLUME: Controls the overall volume of the signal coming from AUDIO OUT.

FILTER: Changes the cutoff frequency of an analog low-pass filter. Turn the knob fully CW and all frequencies (that you can hear) are let through. Start turning it CCW and the high frequencies start getting cut off, until the sound becomes muddy / muffled. Use in conjunction with the SHAPE control to get the tonal quality you are looking for.

Connections:
CV IN: Accepts a 1 volt/octave control voltage to control the pitch of the oscillator. It responds from about 0-5V, but voltages outside of this range won't cause damage. The CV input is quantized, so only valid (western scale) notes are played. This input is ignored when Sample & Hold is enabled.
GATE IN: A voltage greater than about 2.5V will turn on the gate and allow audio to come out the output of the synth.
AUDIO OUT: Connect to an amplifier or another synth. The jack has both the tip and ring connected, so you can even use stereo headphones and hear sound from both ears.
Power: Connect 7.5-15VDC to this 3.5mm TS jack to power the synthesizer. The tip is positive (don't worry, there's a protection diode in case you get it reversed). You can get power from a 9V battery, AC adapter, or you may even be able to find an output on your modular synthesizer that can provide enough current.

Specifications:
Power supply: 7-15VDC (reverse-polarity protected!)
Power connection: 3.5mm phone jack, center-positive
Current draw: 15ma
Dimensions: 3.5" x 2" (the same as a business card!)
Read more
MRP:$108.40 SAVE 19%
coming soon $88.14
FORTHCOMING
Division 6 CEM3340 VCO Module (black faceplate)
Cat: 777957
 
VCO module
Notes: This Voltage-Controlled Oscillator is based on the Curtis CEM3340 IC.

Specifications:
Power supply: +/- 12V to 15 VDC
Power connection: Eurorack 10-pin shrouded header (Can hook wires to pin holes instead if not building for Eurorack)
Current draw: 9mA (+12V) / 6mA (-12V) / 0mA (+5)
Dimensions, main board: 50mm x 60mm
Eurorack HP: 4
Eurorack depth: 64mm
Read more
MRP:$156.72 SAVE 19%
coming soon $127.32
FORTHCOMING
Division 6 Dual Mini Sequencer V2 Module (black faceplate)
Cat: 777964
 
sequencer module
Notes: The Division 6 Dual Mini Sequencer gives you two handy little sequencers behind one Eurorack panel. Why would you need more than one sequencer? Why would you need mini sequencers?

More sequencers = more steps
Use one for playing notes and the other for transposing those notes
Can be used as a clock divider
Run in parallel for multiple CVs / triggers
Each one gives you the standard CV and gate out, plus an ACC out (Accent? Accessory?) Use it to open up a filter, enable a glide, trigger a drum, or whatever you can think of.

The two sequencers will run completely independently, or you can daisy-chain them using the XP IN/OUT jacks to create sequences of any length.

Each sequencer has its own internal clock to get you up and running in a hurry, but you can connect an external clock if you need greater control of tempo or want to sync with other devices.

The module stores your latest sequence even when the power has been removed (plus some other ones in v2!).

While this kit is designed to give you a Eurorack module, the PCB patterns for the jacks also have holes that will accept Johnson/Cinch-style banana jacks. There are also standoff holes on the main PCB, so you can mount them behind your own custom panel.

This module has lots of LEDs and is very shiny, but only two of them are ever on at a time which keeps it from loading down your power supply.

Inputs:
CLK IN (External clock input)
XP IN (Expansion input; Starts sequencer back at step 1. Use for daisy-chaining multiple units)

Outputs:
XP OUT (Sends pulse when sequencer goes past last step. Use for daisy-chaining multiple units)
CV OUT
GATE OUT
ACC OUT (Can be programmed on or off in each sequence step)

Power supply: +12VDC (reverse-polarity protected!).
Power supply (Optional): +15VDC
Current draw: 30ma (+12V) / 0ma (-12V) / 0ma (+5)
Width: 18HP
Depth: 0.83in / 21mm
Read more
MRP:$250.75 SAVE 19%
coming soon $202.42
Items 1 to 4 of 4 on page 1 of 1

Filter

Division 6
Release Date
Featured
Close