安全购物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全购物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Flame

首页  Labels  

Flame

Options
Items 1 to 14 of 14 on page 1 of 1
Flame 4 Vox Quad Wavetable Oscillator Module
Cat: 690791 Rel: 30 May 18
 
Quad polyphonic wavetable oscillator with 4 voices per VCO - 29HP
Notes: The 4Vox is a quad wavetable oscillator with up to four voices per VCO, resulting in a maximum of 16 voices at four individual outputs. With the MIDI In, the module can be played both with CVs and directly via MIDI, which also allows for modulating some additional parameters. There are 39 memory locations for wavetables and 32 for all global parameters of the VCOs.

The parameters of a wavetable can be controlled by CVs and by MIDI. For instance, you can morph through a wavetable with a CV, a MIDI controller or manually with the potentiometer. The range of waves within a wavetable can be selected by minimum and maximum values individually per voice which allows for creating more complex morphs.

Further controllable parameters are Detune, Semitone, Octave, Chord, Portamento, Amplitude and Amp Move (90 degrees phase shifted volume modulation of a VCO's 4 voices). Min and max values can be selected for those parameters as well. Via MIDI it's possible to control further parameters (notes, chords, pitch bend, patch selection and wavetable selection).

The VCOs can be played analogue (frequency by Pitch CV input), monophonic via MIDI or 4-voice polyphonic via MIDI.

The VCO can be used as a voltage controllable LFO with 3 modes: loop, one shot and gates. The SYNC input is used to trigger/reset the LFO. In one shot mode the LFO can be used as a trigger delay, too (SYNC = trigger in, GATE = trigger output, PITCH = delay time).

Each VCO has an analogue 1V/octave input including a fine tune control (+/-1 semitone) and pitch control (approx. 10 octaves), two freely assignable CV inputs, two freely assignable potentiometers, a trigger input for Sync/LFO-reset as well as a Gate and VCO/LFO output

The display can show a graphic of the selected waveforms.

All global parameters and also the VCO's settings can be named and saved as a non-volatile patch by the user. 32 memory locations are available.
Read more
MRP:$631.77 SAVE 24%
 1 in stock $480.75
Flame C3 MkII Knob Recorder Module
Cat: 731956 Rel: 16 May 19
 
3-channel module for recording & playing back movements of controllers - 6HP
Notes: The FLAME "C-3 MK2" is a three-channel module for recording and playing back movements of controllers. These can be recorded with each channel's individual knob. The movements will be output as control voltages. The recording time per track is over one minute. The playback speed is adjustable. All three tracks have a common reset input. The track data remains permanently stored (battery-backed memory). The module can be globally switched to bipolar or unipolar voltage range (switch on the PCB).
Read more
 4 in stock $158.38
Flame Curves Analogue Moving Resonance Filter Bank Module
Cat: 690788 Rel: 05 Jun 18
 
Analogue filter bank with integrated modulation sequencer - 31HP
Notes: Flame Curves is an analogue moving resonance filter bank. It includes a twelve-channel analogue filterbank and a pattern player which can be programmed with a software editor. You can use a freeware "Curves editor software" (Win/Mac) for setup and user pattern editing. The module needs a clock to run in pattern-mode. It also features a reset input to set the sequence back to the first step. The memory in the module can save up to 99 patterns. The active pattern can be seen on the display and selected thanks to two buttons.

If Curves is in sequencer mode, the Envelope potentiometer controls the AR envelope, the Variation knob adds random velocity and release, and the Fill potentiometer controls the level of all the channels.

In manual mode, when the sequencer is off, you can select different filter-types with the Variation potentiometer: allpass, lowpass, bandpass 1-3 and highpass. Thanks to the Fill knob it is possible to sweep through the twelve filter bands. The Envelope knob smooths the sweep by activating a second band next to the selected filter band. Thus, the change from one band to another is not so abrupt.

It is also possible to play the twelve filters via MIDI like a drum module, thanks to the supplied MIDI to minijack cable. It even reacts to velocity.

The twelve bands are subdivided in odd and even bands, which you can feed or tap out separately thanks to the various inputs and outputs. Try patching the odd outputs on one side and even outputs on the other side and you will get an amazing stereo effect! ALL output features a Dry/Wet and a Level potentiometer.

Additionally, the module features also a direct audio output and direct VCA input of each filter channel. Thus, it is possible to feed gate, triggers or envelopes to the VCA of various filterbands and play them independently.

Furthermore, there are several CV inputs for controlling Envelope, Variation and Fill parameters as well as the pattern number.
Read more
MRP:$863.33 SAVE 22%
 1 in stock $669.24
Flame Maander Analogue Filter Bank, Synthesiser & Live Sequencer Desktop Module
Cat: 725951 Rel: 26 Jun 19
 
analogue live sequencer
Notes: Create live sequences with in-depth modulation. The Flame Maander Synthesizer & Sequencer is a four voice synthesizer featuring an onboard sequencer and analog filter bank.

The Flame Maander is a highly versatile desktop synth featuring wavetable sound synthesis including 4OX wavetables and individual filter/amp envelopes. This allows you to get in-depth with your sound design. Create real-time patterns and sequences on the fly using the live sequencer and take your performances to the next level.

The Maander Synthesizer also features USB/MIDI connectivity so you can use it in music production in your favourite DAW. You can even morph between filter types for unique sonic results.
Read more
 1 in stock $1,001.64
Flame Memory Joystick Module With Recording & Saving Capabilities
Cat: 680747 Rel: 08 Mar 18
 
Compact joystick module with 8 memory slots & sequencer functionality - 10HP
Notes: With the Memory Joystick, you can control your modular system like an old video game console. Movements of the stick are recordable. Eight positions can be stored and recalled via buttons. Alternatively, it is possible to jump from one to the next value. The feel is then similar to a step sequencer. You can even vary the playback behaviour.

The Memory Joystick will always start in MANUAL MODE:

Moving the joystick generates CV at the X and Y outputs. Pressing HOLD will freeze the current position. The joystick movements are always being recorded in the background while the SAVE button is blinking. By pushing the SAVE button, now lit permanently, the playback of your movements will start. A RESET impulse resets the loop. Easy and enjoyable!

A little more complex, but not less enjoyable, is the second mode of operation. By pushing MEMORY, you enter the MEMORY MODE:

In this mode, you can use the eight buttons to save eight different joystick positions. This means you have a memory of eight values for the X and Y CV-outputs. You can then play these eight memory slots manually with the respective eight buttons, or sequentially with a CV at CV-MEM or with triggers at the TRIGGER input. While being clocked you can choose nine playback PATTERNS by the position of the joystick. So this module is also a joystick-playable eight-step sequencer!

The memory in MEMORY MODE is non-volatile, meaning you can power off your module and return to the exact setting.

Another nice feature of the Memory Joystick: The orientation can be varied by 180 degrees! This way, you can decide whether you want the buttons and jacks on the top or bottom of the module. When using the module upside-down, there is a nice little trick: Push a little switch on the back of the module to invert the X & Y outputs and also shift the starting position of the sequencer by four steps.
Read more
MRP:$226.21 SAVE 17%
 1 in stock $188.50
Flame QSlider Quad Control Voltage Source Module
Cat: 781481 Rel: 26 Jun 20
 
Voltage source module
Notes: The QSlider is an analog CV source with four 60 mm faders.

The control range of the four sliders can be set with two min/max controls.

The Min control sets the output voltage at zero position of the slider and the Max control sets the output voltage at the end position of the slider. The slider now controls between these two voltages. This allows you to limit the control range and still have the full control range of the slider available.

At a second output socket the inverted voltage is available (Min and Max are reversed). So the slider can also be used as a crossmix fader.

Two common channels can be operated uni- or bipolar. The voltage ranges are 0..+10V or +/- 5V.

The output sockets are located on an extra 4HP panel for mounting at any place (with approx. 40cm long connection cable). This way several modules can be mounted seamlessly next to each other.

HP : 18
Read more
MRP:$203.45 SAVE 17%
 1 in stock $169.53
Click for better price!
or call +44 20 7424 1960
quote 781481
Flame u16MCC MIDI CC To CV Module
Flame u16MCC MIDI CC To CV Module (MIDI CC to CV module)
Cat: 757292 Rel: 10 Mar 20
 
MIDI CC to CV module
Notes: Part of the new FLAME Midi family. These 5HP modules use the new Midi-Mini jack standard and all have a Midi-Through socket.
Read more
MRP:$219.51 SAVE 16%
 1 in stock $184.04
Flame uMCLK MIDI To Clock Divider Module
Cat: 757290 Rel: 26 Feb 20
 
MIDI to clock divider module
Notes: The uMCLK Divider module can either work as a MIDI clock divider or as an analog clock divider. The divider outputs are assigned differently in both operating modes.

After receiving a MIDI start command, the module works as a MIDI clock divider. There are fixed dividers on 11 outputs. Via the divider output KEYS, triggers can be triggered and mixed via MIDI notes. The keyboard zone extends over three octaves. With the help of the LEARN key, the receive MIDI channel and the lowest note of this 3-octave range can be defined.

When stopped (i.e. after receiving a MIDI stop command or after switching on), the module works as an analog clock divider and divides the analog clock present at the CLOCK input. The 12 analog divider outputs can be reprogrammed via SYSEX. Ready-made SYSEX files are already available (e.g. for even / odd dividers, Fibonacci series, offbeats, etc.). The RESET input resets the analog counters or serves to deactivate the analog divider.
Read more
MRP:$220.85 SAVE 25%
 1 in stock $166.20
Flame uMGT MIDI To Gate/Velocity Module
Cat: 757294 Rel: 20 Apr 20
 
Gate module
Notes: The FLAME uMGT converts 12 Midi notes (one octave) to gates or velocity outputs.

Features:

1 octave MIDI keyboard to 12 gate or velocity outputs
global Velocity CV output
global GATE output
programmable via Learn function or SYSEX
MIDI input and THRU (TRS MIDI B standard)
HP : 5
Read more
MRP:$227.55 SAVE 19%
 2 in stock $184.04
Flame uMGT MIDI To Gate/Velocity Module (B-STOCK)
Cat: 793335 Rel: 20 Apr 20
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


The FLAME uMGT converts 12 Midi notes (one octave) to gates or velocity outputs.

Features:

1 octave MIDI keyboard to 12 gate or velocity outputs
global Velocity CV output
global GATE output
programmable via Learn function or SYSEX
MIDI input and THRU (TRS MIDI B standard)
HP : 5
Read more
 1 in stock $175.83
FORTHCOMING
Flame uMGT MIDI To Gates Or Velocity Outs Module
Cat: 781487
 
MIDI to gates/velocity outputs module
Notes: The FLAME uMGT converts 12 Midi notes (one octave) to gates or velocity outputs.
Read more
MRP:$227.55 SAVE 17%
coming soon $189.61
FORTHCOMING
Flame uMLFO MIDI Clock To Analog LFO Module
Cat: 781484 Rel: 31 Dec 20
 
MIDI clock to LFO analog LFO module
Notes: The Flame uMLFO consists of 14 MIDI LFOs which are synchronized to the clock. The module also works with analog clock.

Additional analog clock and reset inputs allow to create pingable LFOs.

It is possible to adjust the frequency, waveform and phase of each LFO. 12 presets are selectable via MIDI keyboard. Thanks to Sysex it is possible to program new setups.
Read more
MRP:$227.55 SAVE 17%
coming soon $189.61
Flame uQMCV 4 Voice MIDI To CV Module
Cat: 757295 Rel: 25 Feb 20
 
MIDI to CV module
Notes: The FLAME uQMCV 4Voice provides 1V/oct, gate and velocity CV signals for four voices from the incoming Midi signals and additionally offers an aftertouch and modulation CV output as well as a run transport output and clock output.

Part of the new FLAME Midi family. These 5HP modules use the new Midi-Mini jack standard and all have a Midi-Through socket.
Read more
 1 in stock $184.04
Flame Xpanmix Xfader Panning Recorder Module
Cat: 757288 Rel: 27 Nov 19
 
Crossmixer/panning combination module - 6HP
Notes: The FLAME "XPANMIX" module is a combination of an XFADER (Crossmixer) recorder and a PANNING Mixer recorder. The upper part of the module contains the XFADER with two inputs to one output. In the lower part of the module is the panning mixer with one input to two outputs left/right. The inputs are designed for audio or CV sources with a voltage range of +-5v (Audio Modular Level). In addition, the inputs can be switched separately to +6db audio (for external audio line level sources) using the slide switch on the rear panel.

The movements of the two mix controls can be recorded. The recording time per channel is over two minutes. The playback speed is adjustable in playback. The recorded track is played back once when the Play button is pressed briefly (one shot) or in the loop when the button is pressed a little longer.

Both mixers have a separate reset input as well as a separate CV input (+-5V) for controlling the mix e.g. by an LFO. The track data remains permanently stored (battery buffered memory).

In addition, the output of the XFader is routed to the input of the Panning Mixer if there is no cable in the PAN input. Both mixers are thus connected in sequence and can additionally mix the XFADER in the stereo image.
Read more
 1 in stock $188.50
Click for better price!
or call +44 20 7424 1960
quote 757288
Items 1 to 14 of 14 on page 1 of 1

Filter

Flame
Release Date
Featured
Close