安全购物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全购物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Intellijel

首页  Labels  

Intellijel

Options
Items 1 to 45 of 45 on page 1 of 1
Intellijel 1U x 2HP Blank Panel (Eurorack blank panel)
Cat: 620719 Rel: 29 May 18
 
1U blank panel space made from brushed aluminium - 2HP wide
Notes: Blank panel for Intellijel 1U spaces. Made from high quality brushed aluminium that matches the 1U modules.

These can also be used for DIY purposes if you drill/mill them to fit your own custom circuits.

Comes with 2 screws.
Read more
 4 in stock $5.34
Cat: 563728 Rel: 10 Mar 15
 
Assorted colour patch cables with length of 24"
Notes: 3.5mm Patch Cables - 5 PAK Assorted Colours 24" (60cm)

Excellent quality patch cables for use with Eurorack modules.

Made by AdInfinitum.

Included colours:
RED
GREEN
YELLOW
GREY
BLUE
Read more
 More than 10 in stock $10.92
Cat: 563720 Rel: 10 Mar 15
 
Assorted colour patch cables with length of 6"
Notes: 3.5mm Patch Cables - 5 PAK Assorted Colours 6" (15cm)

Excellent quality patch cables for use with Eurorack modules.

Made by AdInfinitum.

Included colours:
RED
GREEN
YELLOW
GREY
BLUE
Read more
 More than 10 in stock $8.74
Cat: 563722 Rel: 09 Mar 15
 
Assorted colour patch cables with length of 12"
Notes: 3.5mm Patch Cables - 5 PAK Assorted Colours 12" (30cm)

Excellent quality patch cables for use with Eurorack modules.

Made by AdInfinitum.

Included colours:
RED
GREEN
YELLOW
GREY
BLUE
Read more
 More than 10 in stock $9.13
Cat: 739052 Rel: 19 Jul 19
 
Bi-directional audio board with four TRS jacks for 7U cases
Notes: The new, 2nd generation Audio Jacks Board comes pre-installed in every Intellijel 7U case manufactured since early 2019. Because this board is more fully featured than the previous generation, it's available as a stand-alone component for anyone who wishes to update an older 7U case.

You can tell which board you have by looking at the connectors. The new Audio Jacks Board has a large shrouded header flanked by two smaller shrouded headers, flanked by two link connectors at either end. Older boards have only one connector along the bottom edge.

The board holds four Neutrik TRS jacks, each of which can be configured as either an input or an output depending on the modules you connect. This allows you maximum flexibility when configuring your case - whether you wish to use the audio jacks as outputs, inputs, sends & returns; or some combination of these.

The jacks carry different audio signals depending on what you connect to the Audio Jacks Board. Please refer to the manual for more details on the many options available.
Read more
 1 in stock $25.15
Cat: 563544 Rel: 10 Mar 15
 
Dual oscillator subtractive synth voice module, 40HP wide
Notes: The Atlantis is heavily inspired by the architecture and sound of the classic Roland SH-101. It has always been one of our favorite synths and we really liked how the seemingly limited architecture allowed for all sorts of creative and musically useful sounds to be easily generated.

Just like the 101 it is quick to dial in beautifully rich bass and lead sounds. However this module uses triangle core VCOs (based on the Dixie core) instead of Saw core which respond much more musically to FM. The modulation oscillator can be used as an LFO or VCO (audio rate) and both track very precisely over 8 or more octaves.

In the mixer section you can adjust the balance of the primary oscillators waveforms including a sinewave which is normalled to the EXT IN jack. You could also patch in one of the modulation oscillators waveforms into this channel and be able to operate the Atlantis as a proper two oscillator synth. There is a switch labelled "LINK" which enables the modulation vco pitch to be based as an offset of the primary VCO. This is useful when using it as a stacked dual vco or when you have the mod VCO acting as the linear FM source for the primary vco and wish to maintain the ratio.

The filter section is a Roland style cascaded 4 pole multimode filter with LP, BP and HP modes. The LP Boost switch engages a special mode useful for the LP that produces a much fatter and prominent sound that is not drowned out by resonance (unlike the original SH-101). The filter self-oscillates to produce a very clean sine wave which also tracks 1V/Oct. Between the Mod VCO, Primary VCO, Sub Oscillator and resonating filter it is possible to layer up to four different pitches at one time.

The envelope section is an ADSR with a dual range switch. It also can be set to a looping mode which can be gated on/off externally.

The output VCA feeds into a two level output clipping circuit that you can use to get a much ballsier/dirtier sound.
Read more
 2 in stock $607.56
Cat: 563563 Rel: 10 Mar 15
 
Buffered multiple synth module, 2HP wide
Notes: Dual 1 x 3 buffered mult (one audio or cv signal in with multiple buffered outputs).

The output of the first mult is normalled to the input of the second mult to create a 1×6 buffered mult
Read more
 3 in stock $64.00
Click for better price!
or call +44 20 7424 1960
quote 563563
Cat: 563566 Rel: 10 Mar 15
 
Dual complex morphable wavetable VCO eurorack synth module
Notes: Cylonix and Intellijel have collaborated to bring you a very sophisticated and deeply complex Wavetable VCO. At the core of this module is very powerful FPGA board that he has pushed to the absolute max of its capabilities and crammed full of features. We wanted to create a module that really worked well in the modular context so there are a lot of modulation and control possibilities.

CHORDS
Oscillator 1 can be operated in a CHORD mode, which runs 8 copies of the oscillator in parallel with adjustable detuning, leading to very fat, rich waveforms. The oscillators have extensive modulation capabilities including audio rate (98KHz) Frequency and Phase Modulation (FM and PM) via external sources. Nonlinear combination processes allow the outputs of the two oscillators to interact to generate complex timbres and sonic textures.
There are 64 user selectable chords.

WAVEFOLDER
The SHAPESHIFTER module also includes the analog wave folder circuitry from
module to add analog warmth and metallic rasps to the digital oscillator output.
External signals can also be patched in.

PRESETS
The module includes a sophisticated preset mode where panel settings can be stored. There are 12 user-programmable preset slots and another 52 volatile slots that can be used as a scratchpad. These scratchpad slots are initialized to interesting presets on module powerup. The capabilities of the preset mode is not limited to mere passive storage of settings, however. In this mode the user can also step through, or sequence, the settings, either in order or randomly in response to pulses input to the external sync input. This gives the user the ability to generate complex sequences of sounds. The preset mode also allows the user to morph between the current panel settings and a preset providing a very powerful real-time performance tool.

SYNC
8 Different sync modes: HARD, SOFT, REV, HOLD, BUMP, 2=1, 1=2, OFF
with the ability to internally sync to a sub oscillator

PULSE
User selectable modes for the PULSE output: OR, AND, XOR, GLCH, +OSC1, EOC, +OSC2, -OSC2

MOD A modes: (audio rate modulation)
COMBO IN, SHAPE IN, PHASEMOD, VOCODER

MOD B options (all with CV control)

-Combo modes for OSC1 and OSC2:
NORMAL, RING, MIN, PONG, INLV, AND, XOR, GLCH
-Waveform TILT
-Chord mode overdrive
-Delay depth and FB
-Percussive mode decay time
Read more
 6 in stock $476.50
Cat: 643381 Rel: 27 Mar 17
 
Lo-fi digital reverb effect unit
Notes: Digiverb is a lo-fi reverb effect unit that uses an Accutronic digital reverb "tank" module. The sound is somewhere between a virtual spring reverb and a dense multi tap delay but the effect is quite musical and interesting.

Use the Digiverb as a simple and fun way to add some extra dimensions to your patches!
Read more
$66.04 SAVE 10%
 5 in stock $59.44
Click for better price!
or call +44 20 7424 1960
quote 643381
Cat: 602195 Rel: 10 Aug 16
 
Full featured VCO/LFO synth module - 8HP wide
Notes: Full-featured triangle core VCO/LFO

The Dixie II+ is a larger variant of the classic Dixie II. Using the same great triangle core oscillator, it adds a number of features to make it even more versatile with only a modest increase in size. The Dixie II+ makes a great primary oscillator for a modular system, or a great companion the Rubicon.
Read more
 More than 10 in stock $202.18
Cat: 563579 Rel: 10 Mar 15
 
Dual slider based ADSR envelope synth module, 14HP wide
Notes: The circuit is based in part on the Roland SH-101 / System100m design with several enhancements.
Read more
 1 in stock $201.16
Cat: 747513 Rel: 07 Nov 19
 
Two high quality & precise linear VCA's - 8HP
Notes: The Voltage Controlled Amplifier or "VCA" is one of the most essential and useful building blocks in a synthesis patch. The DUAL VCA 1U packs two high quality, DC coupled, linear VCAs into a very compact 1U package.

The two VCAs can be used completely independently or in tandem via the handy signal normalling. The DC coupling means that the VCA can be used for the amplitude control of both control voltages (CV) and audio signals.

Some application/use examples:

- Dual, independent VCA for dynamic level control of two different audio or cv sources
- Stereo VCA (use the CV normalling where CV A normals to CV B) for processing stereo sources or CV pairs.
- CV/Audio summing (when Out A is not patched, it normals to sum with OUT B, CV A and B control the independent levels)
- Voltage/signal doubling (use input A only and the doubled voltage will appear at OUT B when a CV of +5V applied to CV A)
Read more
 4 in stock $93.46
Click for better price!
or call +44 20 7424 1960
quote 747513
Cat: 747516 Rel: 18 Nov 19
 
Compact dual attenuator, inverter, attenuverter, multiplier, mixer & DC voltage source
Notes: Duatt is a dual-channel active/buffered attenuverter and summing mixer. Each channel has a knob, which can function as a unipolar attenuator or a bipolar attenuverter, depending on the setting of its corresponding two-position polarity switch. It's a versatile and super handy utility module that will find its way into almost any patch you make!

Each input is normalled to a built-in +5V DC voltage source. With nothing plugged into the jacks, each knob controls a voltage range of 0 to +5 V or -5 to +5 V depending on the position of the channel polarity switch.

Channel A's output is normalled into the output of channel B for mixing duties, and channel A has a 2x voltage multiplier switch, allowing you to double the voltage sent into Channel A.
Read more
 More than 10 in stock $58.92
Cat: 747522 Rel: 15 Nov 19
 
Force sensing module with gate & CV output - 10HP
Notes: The FSR 1U is built around a custom fabricated FSR with an analog processing circuit. It allows you to generate a variable CV when you press on it (pressing harder generates a larger voltage) along with a corresponding gate signal.

Guaranteed to add some fun, dynamic control over almost any kind of patch!
Read more
 3 in stock $63.00
Click for better price!
or call +44 20 7424 1960
quote 747522
Cat: 643382 Rel: 27 Mar 17
 
Headphone & stereo output module
Notes: This is a simple 1U module designed to allow the monitoring of a system using headphones. However, if your cat isn't easily scared, the headphone jack doubles as a TRS stereo line level output. Simply connect the signal that you want to monitor to the 1/8? jacks, plug in your headphones, and adjust the volume as desired.
Read more
 1 in stock $74.16
Click for better price!
or call +44 20 7424 1960
quote 643382
Cat: 563718 Rel: 09 Mar 15
 
4 channel hub turns about eurorack patch cable into a mult
Notes: The idea is to allow you to turn any cable into a mult. Connect any Eurorack compatible patch cable to the HUB and then leave them hanging off your patch or magnetically attached to strategic points. This makes more room for the user interface of your modules and complex patches are easy to trace through.
Read more
$11.17 SAVE 10%
 More than 10 in stock $10.05
Cat: 563719 Rel: 09 Mar 15
 
4 channel hub turns about eurorack patch cable into a mult
Notes: The idea is to allow you to turn any cable into a mult. Connect any Eurorack compatible patch cable to the HUB and then leave them hanging off your patch or magnetically attached to strategic points. This makes more room for the user interface of your modules and complex patches are easy to trace through.

Read more
 2 in stock $10.83
Cat: 563664 Rel: 10 Mar 15
 
Complex multi stage pitch and gate sequencer synth module, 34HP wide
Notes: Still one of the best sequencers in Eurorack, inspired by the ultra-rare RYK M-185 sequencer from 2009. Eight stages, ten modes, built-in clock and huge performance options.

Supplier's notes:
The Metropolis is a unique and powerful musical sequencer inspired by the Ryk M-185 (a Roland System 100m format sequencer.) but with many additional enhancements and functions.

The Metropolis comprises eight "STAGES", each with its own assignable gate mode, pulse count and pitch value. Each stage can also have a special slide or skip function activated too. The slide functionality is a constant time portamento very similar to the Roland TB303 (unlike most synths/sequencers that use constant rate portamento) which produces a very musical and interesting result.

In addition to the base sequencer settings set with the sliders and switches there is a full menu of controls and auxiliary modifiers that allows the user to control and manipulate the sequence in many powerful ways including sequencer direction modes, pitch quantization and scale manipulators, clock dividers, shuffle and much more
Read more
 5 in stock $532.38
Click for better price!
or call +44 20 7424 1960
quote 563664
Cat: 677563 Rel: 26 Feb 18
 
Dual multi-mode self-oscillating VCF & crossfader - 20HP
Notes: This is the third generation of Intellijel's much loved Korgasmatron filter designed in collaboration with David G. Dixon. The Morgasmatron features two completely independent six-mode filters (labelled "A" and "B") - each with its own mode-select knob, input, output, cutoff, resonance, Q-drive and gain control. Each filter has a pair of CV inputs (one with a built-in attenuator and the other with a built-in attenuverter) for modulating cut-off, and another CV input for modulating resonance. Both filters self-oscillate at maximum Q, and produce pitched sine waves that track the two separate 1V/OCT inputs.

You can use the two filters independently of one another, or you can use them together (in either a series or parallel connection) and smoothly crossfade between them using either the XFADE knob or the XFADE CV input and built-in attenuverter. You can flip the DRY switches to instantly bypass either or both filters; invert the phase of Filter B; or overdrive Filter A by switching on the new Overdrive circuit. A MIX output provides (as you might suspect) a mixed output of the two filters.
Read more
 5 in stock $343.41
Cat: 563665 Rel: 11 Mar 15
 
Passive multiple synth module, 2HP wide
Notes: Dual 4-way passive mult (one audio or cv signal in with multiple unbuffered outputs)

On the back of the pcb is a pair of solder points marked as "link". You can connect these (with a solder blob or small jumper wire) to turn the mult into a single 8 channel Mult instead of 2 x 4 channel.
Read more
 3 in stock $29.21
Cat: 643383 Rel: 27 Mar 17
 
Utility module featuring Clock, Random Pulse, Analog Noise, Sample/Hold & Slew
Notes: Noise Random Tools comprises a collection of useful utility blocks that you could use in many of your patches - Clock, Random Pulse, Analog Noise, Sample and Hold, and Slew.

Features:

- Clock and Random pulse source with adjustable rate
- Analog pink and white noise source with very accurate spectrum
- Analog sample / track and hold with very low droop
- Analog slew with adjustable slew rate
Read more
 5 in stock $106.67
Click for better price!
or call +44 20 7424 1960
quote 643383
Cat: 739049 Rel: 19 Jul 19
 
Headphone amp capable of driving high impedance headphones via a 1/4" stereo Neutrik jack
Notes: Outs enables your modular system to output both professional and prosumer compliant audio, and send it to external amplifiers, mixers, recording devices, or DAW interfaces. Using the L+R Level knob, it scales modular-level voltages down to the level required to drive external gear at either the +4dBu balanced professional line-level standard or the -10 dbV unbalanced standard.

Headphone monitoring is also provided via a low noise built-in headphone amp (with its own independent level control), capable of driving a wide range of impedances - from studio grade headphones to portable style earbuds.

To use Outs, simply connect the final output of your patch to the 1/8" inputs (where the built-in activity LEDs light up to indicate the presence and intensity of the input signal). The left input is normalled to the right, so you can create a stereo signal from a mono source. Or if you have an Intellijel Mixup, you can remove a jumper from its rear panel, and connect it to the Outs module using the 3-pin link cable included with the Mixup.
Read more
 1 in stock $136.15
Notes: Your Palette case is the ideal solution for your space conscious and portable needs. At about the same size as a small laptop, your Palette fits comfortably on your desktop; in your backpack; at your favourite coffee shop; in your jam space; or pretty much anywhere else you might desire to play. Your imagination is the only limit. With 62hp of rack space, you can piece together powerful but focused mini systems and control surfaces. Intellijel's 1U row and built-in i/o ports add a ton of extra utility to bring the most out of your Eurorack modules. Truly a palette for the sonic artist.

Utilities panel:

- Dual 1:4 buffered multiple
- Two 1/4" balanced audio jacks that can be connected to the Stereo Line Out 1U, Pedal I/O 1U or Mixup
- 1/8" (6.35mm) MIDI Input that can be connected to uMIDI 1U
- USB port that connects to the uMIDI 1U and other future modules
- Rocker switch and barrel plug for power entry

Construction:

- Anodized aluminium
- Aluminium extruded rails with steel threaded inserts
- Rubber feet to protect your desktop
- Rear mounted power supply for maximum module depth

Includes:

- 40W Meanwell AC/DC adapter with right angled connector
- 3FT North American IEC power cable
- 1/8" (6.35mm) TRS to 5-Pin Din MIDI adapter
Read more
 3 in stock $287.52
Click for better price!
or call +44 20 7424 1960
quote 739054
Notes: Your Palette case is the ideal solution for your space conscious and portable needs. At about the same size as a small laptop, your Palette fits comfortably on your desktop; in your backpack; at your favourite coffee shop; in your jam space; or pretty much anywhere else you might desire to play. Your imagination is the only limit. With 62hp of rack space, you can piece together powerful but focused mini systems and control surfaces. Intellijel's 1U row and built-in i/o ports add a ton of extra utility to bring the most out of your Eurorack modules. Truly a palette for the sonic artist.

Utilities panel:

- Dual 1:4 buffered multiple
- Two 1/4" balanced audio jacks that can be connected to the Stereo Line Out 1U, Pedal I/O 1U or Mixup
- 1/8" (6.35mm) MIDI Input that can be connected to uMIDI 1U
- USB port that connects to the uMIDI 1U and other future modules
- Rocker switch and barrel plug for power entry

Construction:

- Anodized aluminium
- Aluminium extruded rails with steel threaded inserts
- Rubber feet to protect your desktop
- Rear mounted power supply for maximum module depth

Includes:

- 40W Meanwell AC/DC adapter with right angled connector
- 3FT North American IEC power cable
- 1/8" (6.35mm) TRS to 5-Pin Din MIDI adapter
Read more
 2 in stock $267.21
Cat: 673903 Rel: 12 Jan 18
 
Intellijel case adapter
Notes: This adapter allows you to use the rear audio jacks on Intellijel 7U cases with up to two Pedal I/O 1U interfaces. It eliminates the need for the Pedal I/O JACKS 1U module.
Read more
 1 in stock $11.44
Cat: 673902 Rel: 12 Jan 18
 
1/4" TS jack interface for the Pedal I/O 1U system - 8HP
Notes: The Pedal I/O JACKS 1U Module allows you to patch standard 1/4? TS cables to and from your guitar/instrument pedals.

This module only works when connected to a Pedal I/O 1U module via ribbon cable.
Read more
 2 in stock $20.31
Cat: 677564 Rel: 24 Aug 18
 
Joystick/vector mixer for CV or Audio - 14HP
Notes: The most complex modulator is you. The Planar 2 puts macro control over six outputs - including a quad panning mixer - into your hands with a buttery smooth joystick. Record up to 30 seconds of your own movements, stretch it or mangle it with scan mode, use a trigger for playback, or just loop it - synced or not. Add yourself to your patch.

With its smoothly responsive precision joystick, Planar 2 facilitates hands-on vector control of two entirely independent sets of outputs (quadrants A-D, and axis X/Y), plus the ability to capture and playback your gestures. Recording your joystick movements enables the creation of organic and complex envelopes, wild and wobbly LFOs, or extended sonic evolutions. It mixes, morphs, routes and pans audio inputs; triggers gates; outputs control voltages and is itself, CV-controllable. Planar 2 puts the 'joy' back in 'joystick,' and the 'fun' back in 'function generator.' Its multitasking and tactile interface makes it a flexible and unique control device, no matter what your musical genre.
Read more
 8 in stock $301.24
Cat: 620700 Rel: 10 Aug 16
 
Versatile Multimode VCF + Phaser synth module in Eurorack format - 10HP wide
Notes: The Polaris is a 4-stage cascaded OTA filter designed by David Dixon. It builds on the lineage of the Dr. Octature and Atlantis filters, but with a totally revised core and resonance control. Along with dedicated LP, HP and BP outputs it features a configurable MULTI output capable of an unprecedented 27 different filter modes.

With drive turned down the Polaris is capable of buttery smooth filtering, and the cutoff control range has been fine-tuned for playability. With the drive dialled up and the new asymmetric multi distortion circuit engaged it creates a more aggressive sound. Not content to be just a filter, the Polaris's AP phaser mode combined with frequency modulation can be used to achieve a phaser effect.

With so much versatility in a modest size, the Polaris is an ideal filter for a starter system and an excellent addition to the tonal palette of a larger modular.
Read more
 2 in stock $207.26
Cat: 643379 Rel: 13 Sep 17
 
Quad voltage controlled amplifier & cascaded mixer - 12HP wide
Notes: The Quad VCA is a compact and feature packed module that is sure to find its way it almost all of your patches. In addition to being used for standard VCA duties it can also be used as a mixer and signal booster.

Features:

- Manual LEVEL control per VCA which is convenient when using the module as a mixer or for biasing when CV modulating the VCA with a bipolar LFO.
- Dedicated CV attenuators with dual colour LEDs for monitoring bipolar CV signals.
- Continuously adjustable response from linear to exponential per VCA.
- Each CV input is normalled to the adjacent one for cascaded control.
- Each output is normalled to the mix input of the adjacent one which allows you to use adjacent sets as submixes or the fourth output can be used as a master mix output when none of the other outputs are patched.
- Each VCA has a boost switch that increases the output level by approximately +6dB (double).
Read more
 More than 10 in stock $176.78
Click for better price!
or call +44 20 7424 1960
quote 643379
Cat: 747527 Rel: 18 Nov 19
 
Quad Function/Burst Generator/LFO with CV Matrix
Notes: Super-versatile quad envelope generator and LFO source from the Vancouver Eurorack brand. All CV controllable and with tons of shaping options.

Supplier's notes:
The Intellijel Quadrax consists of four independent, CV-controllable channels, each of which can be configured to perform any one of the following functions:

- An AD (Attack, Decay) envelope
- An AHR (Attack, Hold, Release) envelope
- A cycling envelope (resulting in a unipolar LFO)
- A pulse burst generator (Finite repeated functions that ascend or descend in amplitude)
- A morphing, bipolar beat syncable LFO

The envelopes all feature a continuously variable response curve, ranging from logarithmic through linear to exponential, and each stage can be as snappy as 0.3 ms to as lengthy as 20 seconds.

When set to Burst mode, the channel generates a rising or falling burst of pulses, with full control over the length of the pulse burst, the number and shape of the bursts within it, and whether the bursts increase or decrease in amplitude over the burst.

AD, AHR, Cycling and Burst modes all feature a user-selectable maximum output level of either 5V or 10V.

LFO mode offers control over the frequency and waveshape, while providing a unique morphing feature that creates numerous variations of the selected waveshape. LFOs can be either free-running or beat-synchronized using the channel's TRIG input.

Channels can be chained together to create complex multi-stage envelopes, with each channel triggered by the previous channel's trigger input, end-of-rise, or end-of-fall. This enables multiple function generators to fire simultaneously, or it enables the creation of complex multi-stage envelopes by allowing the linked function to fire either at the end of the previous function's rise time, or at the end of its fall time.

Four freely-assignable, step-attenuverted CV inputs are capable of modulating any or all of the various parameters across all four channels using the built-in CV matrix, and built-in attenuversion for each assignment.

Quadrax remembers its current state (Mode and CV assignments, channel links, etc) and retains that state even if power is removed, meaning Quadrax will always turn on in exactly the same state as you last left it.
Read more
 1 in stock $319.03
Click for better price!
or call +44 20 7424 1960
quote 747527
Cat: 747528 Rel: 18 Nov 19
 
Quadrax EOR/EOF expander featuring 8 additional gate/trigger outputs
Notes: The Qx expander adds an EOR (End Of Rise) and an EOF (End Of Fall) trigger/gate output to each of Quadrax's four channels, enabling Quadrax's envelopes, cycles, bursts and LFOs to trigger external modules.

Requires the Quadrax to function.
Read more
 6 in stock $63.00
Cat: 718062 Rel: 18 Feb 19
 
2-channel quantizer & step sequencer - 8HP
Notes: Scales is an 8hp dual-channel note quantizer and step sequencer. Fundamentally, it takes an input voltage, quantizes it to notes in a user-defined scale, and sends that quantized voltage to an output, where you can use it as a melodic pitch source for oscillators or any other module that expects to see discreet note values at its input.

Scales goes far beyond the fundamental, allowing you unprecedented control of the pitches and intervals hiding inside your control voltages; turn LFO's into arpeggiators; random voltages into harmonic counterpoint; and unquantized external CV sequencers into chromatically tuned note sequencers.

Quantization can be locked to an incoming trigger. There are a number of trigger output options as well, ranging from no triggering (good for pitch shifting drones); through triggers that sync with either of the two outputs (or both); to a trigger or gate transmitted in sync with one sent to the module's TRIG input.

Shift:

Scales features two independent outputs, enabling you to create shifted harmonic intervals within your chosen scale using only a single pitch input. Using the SHIFT input you can modulate changes on OUT A and/or OUT B.

You can also use the shift input to switch between scales or to change the root of any existing scale pattern or split Scales into two quantizers - each conforming to a common scale, but fed entirely different voltage sources.

Sequence:

Scales also features a 128-step SH-101 style step sequencer (complete with storage for up to 35 fully programmable patterns) - allowing you to feed OUT B with sequenced notes and rhythm patterns, while OUT A continues to function as a standard pitch quantizer for external voltages. You can even sync the sequencer to quantizer events on OUT A.
Read more
 4 in stock $278.38
Cat: 643384 Rel: 27 Mar 17
 
Voice allocator, note hocketing & analog shift register module - 6HP
Notes: The Shifty is essentially a combination of four sample and hold stages, a sequential gate and sequencer controller. This collection of functions allows for some specific and useful utility application.

One of the primary uses for Shifty is to take a monophonic sequence source and route each new note of the sequence to up to four different synthesizer voices in a specific pattern. In this way you can create pseudo polyphonic sequences since each voice can be triggered to play and sustain while the next voice int the sequence gets triggered. Another term for this is hocketing.

The other main application of the Shifty is to function as an Analog Shift Register. In this mode each new gate input received causes the current set of pitches to be shifted to new output locations as a new one is added and the oldest one is replaced. This can be an interesting way to create chords that are up to four stacked notes when used with a pitch sequence source that has a harmonious series of notes (e.g. a pentatonic scale works really well). Even just using two of the outputs will yield very interesting melodic interplay and is an excellent way to make a simple sequence much more complex and interesting.

In a more basic way the Shifty could be used as a simple Sample/Track and Hold module or as a sequential gate.
Read more
 5 in stock $171.70
Cat: 643391 Rel: 29 May 18
 
Updated version of the Springray module with added parametric EQ
Notes: There are many excellent digital reverbs available these days but there is still nothing quite like the timeless and magical character of a true spring reverb.

For the Intellijel Springray II, each tank has a totally different set of characteristics, with many unexpected surprises when feeding it through a wide variety of sound sources. One of the most interesting results is how a slow attack saw waveform from a Dixie almost sounds like a realistic cello!

Version two of the Springray provides a number of changes and improvements to the original design. The shelving EQs have been replaced with a parametric EQ with frequency, Q, and gain controls. The CV inputs for feedback and mix balance have been replaced with inputs to control the filter frequency and gain. Lastly, the feedback and limiter circuits have been redesigned, and the drive quality has been improved.

PLEASE NOTE: Does not include Spring Reverb Tank.
Read more
 1 in stock $214.37
Cat: 718065 Rel: 18 Feb 19
 
4 track gate & trigger sequencer - 8HP
Notes: Steppy is a 4-track programmable gate sequencer with eight internal memory slots, external clocking, numerous tweakable parameters, and a performance-first design aesthetic.

Each track features numerous independent parameters that govern its playback independently of the other tracks. Specifically:

- Each track has its own length, which can range from 1-step to 64-steps, allowing for polyrhythms, fills, or constantly evolving gate interactions between tracks.
- Each track has its own gate length, which ranges from very short to very long, with tied gates possible at the extreme setting.
- Each track has its own clock divider, allowing patterns to play out over completely different periods of time.
- Each track has its own swing setting, which offsets the timing of every other step.
- Each track has its own delay setting, which offsets the timing of every step.
- Each track has its own probability control, which sets the likelihood that each programmed gate will fire when called upon by the pattern.
- Each track can be shifted (or 'rotated') forward or backward by a number of steps. So if you've created a pattern that 'feels' like it has its downbeat on step 3, you can shift that pattern two steps to the left, so that the downbeat sits on step 1.

Tracks can be programmed by entering active steps on the grid or tapped in live as the sequence is moving. Tracks can be selected and modified in real time as the sequence plays. A select button allows you to directly access each track (and each page of 16 steps within that track) directly through Steppy's intuitive multifunction buttons array.

Tracks can be individually muted and unmuted, and a special performance mode (called "Loopy") enables you to touch any two gate steps and instantly create a performance that loops between those steps.

Track patterns can be cleared without clearing its playback parameters, and all track patterns (along with their individual playback and performance parameters) can be saved as a preset to one of eight internal memory slots.
Read more
 2 in stock $227.59
Click for better price!
or call +44 20 7424 1960
quote 718065
Cat: 768942 Rel: 13 Mar 20
 
audio input module
Notes: Use the Stereo Line In 1U system to bring external audio into your modular system for processing. The system works with balanced +4 dBu professional audio products and with -10dbV unbalanced gear.

The Stereo Line In 1U system comprises two components:

The Stereo Line In 1U module:
Either a Stereo In Jacks 1U module, or a case with built-in 14" audio jacks, such as Intellijel's Palette or 7U cases (with a 2nd generation Audio Jacks board).

Width: 12HP
Depth: 38mm
Power: 18mA @ +12V
12mA @ -12V
Read more
MRP:$78.03 SAVE 17%
 More than 10 in stock $65.02
Cat: 768945 Rel: 13 Mar 20
 
synth module
Notes: 1/4" TRS Jack Panel For Stereo Line In 1U Module

If you don't own an Intellijel case with built-in compatible 14" jacks, then you need to purchase a Stereo Line In Jacks 1U module, which connects via ribbon cable to the Stereo Line In 1U module to provide 14" TRS input jacks for interfacing with other studio or stage gear.

Width: 8HP
Depth: 39mm
Read more
MRP:$21.95 SAVE 14%
 3 in stock $18.80
Cat: 739060 Rel: 29 Jul 19
 
Dedicated jack expansion module for use with the Stereo Out 1U module
Notes: 1/4" TRS jack panel in 1U for the Stereo Line Out 1U module.

If you don't own an Intellijel case with built-in compatible 1/4" jacks, then you need to purchase a Stereo Out Jacks 1U module, which connects via ribbon cable to the Stereo Line Out 1U module to provide 1/4" TRS output jacks for interfacing with other studio or stage gear.
Read more
 2 in stock $20.82
Intellijel Tete Module (synth module)
Cat: 747529 Rel: 30 Dec 19
 
Expander module for the Tetrapad controller
Notes: Expander module for the Tetrapad, Intellijel's multi-dimensional performance touch controller. Adds huge functionality, allowing you to sequence parameters and create complex modulation.

Supllier notes:
Tete is the long awaited and highly anticipated expander for the Tetrapad.

Some of the key features:

Three primary modes: VOLTAGES, NOTES and COMBO.

VOLTAGES mode:

Up to 16 voltage storage locations (grid) with 8 voltages stored at each location.

You have the choice to record and playback your recall of these locations in a looper style (just play freely and spend arbitrary amount of time at any location) or as a clocked sequence (SH-101 style). Additionally you can traverse the matrix using the X and Y CV inputs to get Cartesian style sequencing.

There is also variable slew that allows you to morph/glide between the values.

NOTES mode:

You can create sequences or loops in chord, scales or keyboard mode. The isomorphic keyboard grid can vary from 4 notes to 12 notes max. There are real-time performance looping, transposition and inversion capabilities via the CV inputs and dedicated loop button. In sequencer mode each step can be a tie, rest, or gate with size 25/50/75%. Basically we have created a way to very quickly and intuitively make chord sequences that are very musical and easy to manipulate. It is difficult to summarize in words but we will be sure to create some videos to demonstrate how easy and fun this is to play with. It definitely represents something unique in the landscape of Eurorack sequencers.

COMBO mode:

In this mode you can loop record your performance on any combination of the following functions:

fader, bipolar fader, drum hit, switch or LFO. Kind of like Elektron style parameter locking but all of the motions is recorded continuously instead of just in slices. Instantly turn a simple patch into a highly animated and complex beast.

With all of the above mentioned loop recording modes you can very easily overdub since the Tetrapad detects pressure/pressing. In combo mode you can erase individual channels.

All modes allow for internal or external clocking and configurable syncing.

All of the modes have special XYZ CV modulation assignments and make use of the dedicated CV outputs.

For example, in Looper mode one of the CV outputs generates a continuous ramp that represents the position in the loop. This can be used with devices like the Planar 2 in Interpolation mode to sync the recorded patterns together no matter what tempo.
Read more
 6 in stock $282.45
Cat: 739050 Rel: 19 Jul 19
 
Three-channel active/buffered attenuverter & summing mixer
Notes: Triplatt is a three-channel active/buffered attenuverter and summing mixer. Each channel has a knob, which can function as a unipolar attenuator or a bipolar attenuverter, depending on the setting of its corresponding two-position polarity switch.

Each input is normalled to a built-in precision +5V DC voltage source. With nothing plugged into the jacks, each knob controls a voltage range of 0 to +5 V or -5 to +5 V depending on the position of the channel polarity switch. Outputs A and B are also capable of a range of 0-10 / -10 to +10 when using the special function switches.

Each output is normalled to mix into the output of the channel below, making it possible to do sub mixes in groups of two or three.

In addition, each channel has a "special function" switch to alter its input voltage in a specific way. Channel A has a 2x voltage multiplier switch, allowing you to double the voltage sent into Channel A. Channel B has a +5V switch, allowing you to add 5V to whatever voltage is sent into Channel B. Channel C has a mute switch, allowing you to completely turn off the signal being sent into Channel C.
Read more
 1 in stock $99.56
Cat: 563709 Rel: 10 Mar 15
 
Dual 3:1/6:1 unity gain mixer (for cv or audio) synth module, 2HP wide
Notes: Dual 3:1 audio and cv mixer (up to three buffered inputs with a single buffered output).

NOTE: Version 2 of the Unity Mixer has two sets of jumpers on the main pcb. These allow the top and bottom sum to be set to -6dB attenuation instead of unity gain. This creates more headroom when summing higher amplitude sources like raw VCO signals.
Read more
 6 in stock $69.09
Cat: 563713 Rel: 10 Mar 15
 
Voltage controlled amplifier Eurorack synth module with continuously adjustable curve response (from linear to exponential)
Notes: This is the version II of the original uVCA.

This module was adapted from a design by David G. Dixon
Read more
 1 in stock $138.17
Cat: 563716 Rel: 10 Mar 15
 
Voltage controlled filter synth module with low pass (LPF) 2-pole, high pass (HPF) 2-pole and bandpass outputs (BPF) 1-pole
Notes: Introducing the uVCF state variable filter.

This is another great David Dixon filter design that has been on the workbench for a while. It is a very clean and precise filter that also doubles as an excellent sine VCO.

It responds very well to FM and the small size should make it a nice choice for smaller systems/lunchboxes.
Read more
 1 in stock $143.26
Cat: 716898 Rel: 30 Jan 19
 
2-channel Eurorack oscilloscope - 16HP
Notes: Sometimes your ears are not enough and you really need to see the sounds and control voltages you are generating. Zeroscope's two channel design lets you display and compare both control voltages and audio. It's a good old fashioned sci-fi light show!

The Zeroscope 1U is an adaptation of the excellent 3U Zeroscope by VPME.DE.

Three Modes Packed Into 1U:

- Scope: Standard graphical display, with time displayed on the X-axis and voltage displayed on the Y-axis.
- X-Y: Alternate graphical display with CH 1 driving the X-axis and CH 2 driving the Y-axis.
- Tune: Alphanumerical tuning display, which you can configure to show either Hz values or note names.

The Scope displays have adjustable display offset for each channel and an adjustable trigger threshold, while the tuner has options for reference pitch and average update speed.
Ins & Outs

The inputs are DC coupled and accept signals between -10V and +10V. The Signal on the input is normalled to the output below; this allows you to monitor or tune a signal without a mult or re-patching.
Read more
 2 in stock $134.11
Cat: 643387 Rel: 21 Aug 17
 
Physical modelling percussion synthesiser module - 12HP
Notes: Killer physical modelling module collab from two of the biggest names in their respective fields of hardware and software. Generates a huge range of percussion instruments plus synths and bass tones.

Supplier's notes:
Plonk uses a technique known as physical modelling to synthesize, with great realism, the way in which sound is produced by acoustic instruments. The Plonk module is, itself, focused primarily on creating percussive sounds - both pitched and un-pitched; natural and unnatural; acoustic-sounding or totally electronic.

Plonk does this by breaking sound creation into two distinct elements - the exciter and the resonator. The exciter is a mathematical model of the device used to strike a particular surface. Plonk, because it's percussion oriented, has two types of exciters: one modelled on a mallet, and the other providing a noise source. The resonator is a virtualization of the object being struck, which vibrates, resonates and creates the body of a sound. Plonk offers several types of resonators: beam; marimba; drumhead; membrane; plate; and string.

Plonk provides numerous parameters that let you shape, mould and design both the exciter and the resonator, thus enabling you to synthesize the sound of striking or scraping almost any type of object - real or imagined. In this way, Plonk can accurately model the sounds of kicks, snares, toms, cymbals, claps, tablas, congas and all manner of traditional percussion instruments. It can also model pitched percussive instruments, like vibes, marimbas, and even bass or guitar-like tones. Of course, it additionally excels at modelling instruments that heretofore never existed.

Best of all, the sounds created by Plonk are not static - any sound you design can respond dynamically to velocity, as well as four different modulation inputs. This means the sound of Plonk can change completely from note-to-note (or strike-to-strike). Because of this, Plonk is actually a duophonic (2-voice) module, which lets the sound of one note decay naturally when a second note (possibly employing an entirely different set of modelling values) is struck. Thus, hitting a new note does not choke the sound of the previously struck note (unless you want it to, of course)!

Plonk stores up to 128 patches in its internal memory, and ships with many presets programmed by professional sound designers and composers. You may overwrite these patches if you wish, and banks of patches may be transferred via MIDI System Exclusive over Plonk's built-in mini-USB port to facilitate offline storage by programs or websites that support this capability.

Plonk was developed in cooperation with Montreal-based Applied Acoustics Systems - physical modelling pioneers, and the creators of Tassman, Lounge Lizard, String Studio, Ultra Analog, Chromaphone and numerous other plugins. It is with great pleasure that Intellijel brings the potential of this physical modelling technology to a hands-on, CV-laden device capable of the sort of dynamic control and sonic exploration that modular synthesists demand.
Read more
 3 in stock $333.24
Items 1 to 45 of 45 on page 1 of 1

Filter

Intellijel
Release Date
Featured
Close