搜索结果

Notes: PreSonus showcase their expertise with these painstakingly crafted monitors. Coaxial design offers all the benefits of a point source, for precise stereo imagine and phase alignment.

Supplier's Notes:
Listen to your mixes reproduced with lifelike realism! The Erisr Pro 8's symmetric design and consistent acoustic centre provides superior phase alignment between components to deliver a wide sweet spot, precise stereo imaging, and symmetrical dispersion patterns, making them ideally suited for immersive Dolby Atmos rooms and stereo mix environments alike.

The Eris Pro 8's coaxial design provides a single acoustic point source that creates a natural listening experience, revealing the subtlest nuances in your recordings, while providing a three-dimensional soundstage, detailed transient response, and lifelike sonic reproduction. Combined with a punchy low-end that defies its compact size, the Eris Pro 8 provides a superior listening experience for both home studios and professional mix rooms.

A 1.25-inch, ultra-low mass, silk-dome tweeter ensures snappy, accurate transient reproduction, while a 8-inch, woven-composite woofer offers tight, clear bass, with plenty of punch and no flab. A ported enclosure and 140 watts of power allows the Eris Pro 8 to reach down to an astonishing 35 Hz, while a finely detailed transient response and stunning dynamics deliver a natural and less fatiguing experience.

Acoustic tuning controls and a three-way Acoustic Space tuning lets you accurately configure the Eris Pro 8 for your room. Flexible input options enable connection to almost any line-level source, from mixers to audio interfaces and more. Provisions for wall and ceiling mounts make it easy to integrate Eris Pro 8 monitors into any stereo or multi-channel system.

Features

Single point-source coaxial design for wider sweet spot and better phase alignment
8-inch, woven-composite, low-frequency driver
1.25-inch, silk-dome, high-frequency driver
140W, Class AB amplification
35 Hz to 20 kHz frequency response
105 dB SPL (Peak, @ 1 meter
Acoustic Tuning Controls: Acoustic Space (Flat, -2 dB, -4 dB), High Frequency (+/-6 dB, center 10 kHz, continuously variable), Mid Frequency (+/-6 dB, center 1 kHz, continuously variable), Low Cut (Flat, 80 Hz, 100 Hz @ -12 dB / octave)
XLR and 14-inch TRS balanced and RCA unbalanced rear-panel stereo inputs
Protection: RF interference, output-current limiting, over-temperature, turn-on/off transient, subsonic filter
Power Saver mode (engages after 40 minutes)
Wall and ceiling mountable

Inspired design for inspiring results

Placing the high-frequency driver in the centre of the low-frequency driver increases clarity, widens stereo imaging, and produces an incredibly even mid-range. Vocal clarity, the attack of a snare, and guitar presence shine through, allowing you to quickly and accurately place them in a mix and get the results you desire faster than ever before.

Symmetric response

The Eris Pro 8's coaxial design provide a symmetrical dispersion resulting in a crisper stereo image, greater soundstage depth, and superior separation between components in a complex mix.

Set up your studio monitors for your room

Acoustic Tuning controls ensure you'll get the flattest frequency response possible in your mix environment. You get Low Cut, Mid, and High controls, as well as 3-way Acoustic Space tuning that allows you to easily compensate for the sonic consequences of speaker placement against a wall or in a corner.

Specs

Electronics

Voltage: 220-240V UK
Wattage: 140 Watts
INPUT IMPEDANCE
Input impedance: 10KO

Performance
Peak SPL: 108 dB (@ 1 Meter)

Speakers
Crossover frequency: 3.1 kHz

Hardware
Cabinet material: Vinyl-Laminated, Medium-Density Fiberboard

Audio controls: Volume High Frequency (+/-6 dB, center 10 kHz, continuously variable) Mid Frequency (+/-6 dB, center 1 kHz, continuously variable)

Audio switches

Acoustic Space (Flat, -2 dB, -4 dB) Low Cut (Flat, 80 Hz, 100 Hz @ -12 dB / octave)

Monitor inputs: 1- Balanced XLR, 1- Balanced 14" TRS, 1- Unbalanced RCA

Power amplifier type: Class AB

Measurements

Dimensions: 12.80 x 10.60 x 12.20 in

Depth: 12.2" (30.1 cm)
Height: 12.82" (32.6 cm)
Width: 10.63" (27 cm)

Notes: R2M is module 1 of a pair of two 2 HP modules that allow you to connect a chain of controllers to your DROID master through a standard 3.5 mm stereo cable (sometimes also called aux-cable).

The usual idea is that you put all your DROID controllers into a skiff case and mount your DROID master, X7 and G8 into another case, together with all your fancy Eurorack sound modules.

R2C is module 2 of a pair of two 2 HP modules that allow you to connect a chain of controllers to your DROID master through a standard 3.5 mm stereo cable (sometimes also called aux-cable).

The usual idea is that you put all your DROID controllers into a skiff case and mount your DROID master, X7 and G8 into another case, together with all your fancy Eurorack sound modules.

While you could do this with the typical 6-pin ribbon connector (e.g. the 80 cm version that we offer), using the R2M/R2C combination has some serious advantages:

The connection cable can be almost arbitrary long (20 m have been tested and works perfectly).

Since the connection is done on the front of the modules, you can quickly disconnect your skiff for the purpose of travelling to a gig.

You can use a standard 3.5 mm stereo TRS cable for the connection.

These modules are not just passive connectors but contain special driver ICs that transform the electronic voltage levels, which run in the 6-pin ribbon, to something more stable and reliable that is fit for longer distances in a more hostile environment.

The controllers do not receive their power from the master but from the R2C module, which has a power connector and a voltage regulator for that purpose. Each chain of the R2C module provides the same power to its controller chain as the master does (it contains the identical voltage regulator). That means that you can connect up to 32 controllers (!) to one R2C.

Another nice thing: The R2M/R2C combination allows for two of these master / controller connections in parallel. That means that you can have two masters being attached to their individual controller chains. That does not mean, that each of the masters can access each of the controllers at the same time, however. Both master / controller connections work completely separately.

Package contents:
* one R2M module
* one R2C module
* one Eurorack power cable for the R2C
* two 6-pin ribbon cables for connecting the R2M to two masters
* two 3.5 mm stereo TRS cables, approx.. 1.2 m
* 4 red M3 screws for mounting the two modules

Notes: The Cosmic ECHO is an analogue-sounding LoFi delay that will work with just about anything you plug into it.

The dark, lush, moody tones of the ever-popular PT2399 IC provide an out-of-this-world experience. Our take on this classic pedal pushes the chip's limits so you can explore all the gritty elements drifting at the edge of long delay rates. It already outperforms other bucket brigade style echoes, but just to be sure, we added 2 momentary switches, Zone and Warp.

Dark, rich sounds with the analogue vibe of a tape echo.

Uses the PT2399 IC, a bucket brigade style emulation. This IC has 16-bit sampling for 30-300 milliseconds. After that, the sample rate goes down in relation to the delay length. This results in artifacts and noise being introduced into the audio for weird, cosmic, psychedelic sounds.

Delay length: 30ms-1,250ms

3 knobs: Feedback, Mix and Rate. The Mix is a wet-only control that attenuates the amount of delayed signal in the signal chain. The Rate controls the number of repeats in an organic-sounding way.

Warp button: Momentary pushbutton switch that gives a bright, "small speaker" tone.

Zone button: Momentary pushbutton switch that introduces feedback into the circuit momentarily. Great for adding rhythmic feedback and other strange sounds. The Zone amount can be adjusted by an internal trim pot.

Pedal may have a slight volume drop.

Great for shoegaze, surf rock, ambient and experimental sounds.

Pedal uses a 125B case

Dimensions (L x W x H): 4 7/8" x 2 5/8" x 2 3/16" (124mm x 67mm x 56mm).

Takes a 9V battery or 9V centre negative 2.1mm barrel power supply (not included).

Notes: This is an envelope follower based on a classic module from the seventies but with some improvements to suit modern needs.

The IN signal is bifurcated to the envelope follower circuit and also to a THRU output, so the original signal is also available for external processing.

The envelope follower has three controls, a switch to select response time (fast, medium, slow), a pot to adjust GATE threshold and a pot to adjust the envelope CV level.

This little module will help you shape the timbre and/or the level envelopes of your sounds. From dynamic envelope filtering to compressor like side chaining there are lots of possibilities to mangle your audio.

Tech specs:

- 4HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 18mA , -12V 16mA

Notes: Module A-105-2V is a voltage controlled low pass filter with 24dB/octave slope.

It is the successor of the A-105 which had to be discontinued because the obsolete SSM2044 filter circuit. The A-105-2 is based on the SSI2144 which is in turn the successor circuit of the SSM2044. The features of both modules are nearly the same. The main difference is the clearly reduced front panel width of the A-105-2 (4HP instead of 8HP) and the associated changes of the controls and sockets positions. In addition the A-105-2 is equipped with 2 audio inputs.

The module has these controls and in/outputs available:

Control Frequ: manual frequency control
Control FCV2: attenuator for the frequency control voltage applied to socket FCV2
Control Q: manual resonance control
Control QCV: attenuator for the resonance control voltage applied to socket QCV
Control Input 1 Level: attenuator for the audio input signal applied to socket Input 1
Socket Input 1: audio input 1 (with attenuator)
Socket Input 2: audio input 2 (without attenuator)
Socket FCV1: frequency control voltage 1 (without attenuator, about 1V/oct scale)
Socket FCV2: frequency control voltage 2 (with attenuator)
Socket QCV: resonance control voltage (with attenuator)
Socket Out: audio output
Technical notes:

Frequency range: about 15Hz ... 15 kHz
Resonance up to self oscillation
Max. input voltage at Input 2 without clipping/distortion: about 15Vpp
Max. output voltage without clipping/distortion: about 15Vpp
The signals of both inputs are mixed before they are processed by the filter. This saves an external mixer for small setups.
Depth: 45 mm

HP : 4

Notes: Red version of Cyclone's excellent bass synth, replicating the sound of the iconic Roland TB-303. Fully analogue synth with modernised sequencer and classic acid sound.

Supplier's Notes:
A full analogue synth clone of the famous TB303, coming with a lot of new features and improvements, from the sound point of view as well as the ergonomics of the machine and the sequencer.

A new design, new pots very smooth, new features for Live jam, 2 new sequencer modes for even more creativity, added CV / Gate (and even more) outputs to play your favourite synths!

The design of the analogue circuit (composed of 1 VCO) and the audio engine has been improved compared to the previous version, giving it a warm and groovy sound thanks to the addition of the Shuffle (not present on the original).

The very intuitive sequencer takes on the original spirit while bringing new and unique features such as Mute and Hammer, which gives it a great flexibility for live jam and more sound variations, as well as 2 new sequencer modes to create New patterns.

Specifications

Bass Bot TT-303

VCO

Monophonic
Waveforms: Sawtooth or Square
Frequency Range: 20Hz-850Hz

Main Controls

Tempo Knob
Volume Knob
Track/Pattern Bank Selector Knob
Mode Selector Knob
Power On/Off Switch

Audio Controls

Tuning Knob
Filter Cutoff Frequency Knob
Filter Resonance Knob
Filter Envelope Modulation Amount Knob
Filter Envelope Decay Knob
Accent Amount Knob
Waveform Selector Switch

Data Storage

User Patterns: 432 (9 banks of 48 patterns)
Pattern Lab Patterns: 108 (9 banks of 12 patterns)
Preset Patterns: 108 (9 banks of 12 patterns)
User Tracks: 9

Operating Modes

Pattern Write | Loop Edit |Pattern Lab | Arpeggiator
Pattern Play | Preset | Track Play | Track Write | MIDI

Per-step Modifiers

Down Octave | Up Octave | Accent | Slide
Mute | Hammer | Rest / Tie

Pattern Features

Pattern Length: 1-64 steps
Per-step modifier assignment
Time scales: 16th note, 32nd note, 8th note triplet,
16th note triplet
Assignable pattern LED color
Pattern Copy / Paste functions
Intelligent procedural pattern generator
Pattern-based Arpeggiator
Pattern Mutate function

Track Features

Visual track programming system
Maximum Length: 144 bars | Per-bar transpose option

Global Features

Shuffle Amount | Slide Time | Gate Length |
Illuminated buttons: 26
Tap Tempo Input | Automated VCO calibration |
System LED colour |
MIDI In / Out channels

Outputs

Main Mix (1/4" mono, +15dBu)
Headphone (1/4" stereo, +10dBu)
VCO Waveform (1/8", Sawtooth: 5Vp-p, Square: 3.7Vp-p)
Control Voltage (1/8", 1V/octave, range 1V 5V)
Gate (1/8", 0V 12V)
Accent On (1/8", 0V 5.5V)
Clock (1/8", DIN Sync compatible, 0V 5V)
Start/Stop (1/8", DIN Sync compatible, 0V 5V)
MIDI Out / Thru

Inputs

Filter In (+4dBu nominal, 100kO input impedance)
Power (9VDC, 300mA) | MIDI In

PC Functions

Cyclone Studio application for PC & Mac enables Bass Bot software update and user data backup & restore using MIDI/SysEx transfer.

Physical

Dimensions: L310mm x W130mm x H35mm
Weight: Unit 783g (Boxed with accessories) 1.332kg

Included Accessories: 100-240v Universal Power Adapter | Near Invisible Force Field | Case Transporter | Printed User Manual

Available Accessories: 7 Lines 1/8 to 1/4 output cable snake | Triple 100-240v Universal Power Adapter

Notes: Unleash your creativity

Designed for seamless pairing with MiCreator Studio, the Satellite microphone unlocks powerful creative flexibility. Link Satellite and MiCreator Studio via the in/out ports to track an additional sound source or even achieve true stereo recordings and capture the energy of the moment. Satellite even works as a standalone mic and offers a headphone jack. Start recording how you want, when you want with Satellite.

Custom Condenser Capsule - Record in top notch audio quality
Max SPL: 130 dB SPL - Record even very loud sources
FlexTilt mechanic - Easily position the mic head for optimal recording
Full metal housing - Longlasting and durable
Headphone jack
Exchangeable & customizable face plates for an individual and personalized look

Technical Specifications

Directional characteristic: Cardioid
Frequency range: 20 Hz - 20 kHz
Max. SPL: 130 dB SPL
Weight: 220g
Dimensions: 100 x 60 x 28 mm

Notes: Turn your MiCreator Studio into a mobile content creation powerhouse with Y-Lav. Record multiple speakers simultaneously by tethering Y-Lav to your MiCreator Studio. And hear your audio in real time with onboard direct monitoring output. No matter what you create, make sure it sounds as good as it looks with Y-Lav.

Pairs seamlessly with MiCreator Studio to unlock powerful creative flexibility
Connected via the Link Connection (In/Out jack on the MiCreator Studio)
Record high-quality audio for video projects and more
Connect a second pair of headphones via the built-in headphone jack

Technical Specifications

Polar pattern: Omni
Connections: 3.5 mm / 1/8" TRRS, 3.5 mm 1/8" TRS Klinke
Weight: 30 g
Dimensions: 35 x 17 x 17 mm

Notes: The Austrian Audio MiCreator is a new type of creative tool. Equal parts high-quality condenser microphone and simple audio interface with USB-C r connectivity, MiCreator gives you the flexibility to create what you want-how you want. Just plug in and start recording in top-notch audio quality instantly. Or expand your setup using MiCreator's additional input to achieve stereo recordings, record an additional sound source, and more. And whether you're recording at home or on the go, you can create with confidence thanks to MiCreator's ultra-durable metal housing. So, whether you're looking for a capable plug-and-play microphone or a multifaceted production tool, MiCreator simplifies your creative process and delivers no-compromise results.

MiCreator System

Unleash your creativity

MiCreator Satellite

TRRS microphone with headphone jack
Custom Condenser Capsule - Record in top notch audio quality
Max SPL: 130 dB SPL - Record even very loud sources
FlexTilt mechanic - Easily position the mic head for optimal recording
Full metal housing - Longlasting and durable
Headphone jack
Exchangeable & customizable face plates for an individual and personalized look


MiCreator Y-Lav
Lavalier microphone with headphone jack
Pairs seamlessly with MiCreator Studio to unlock powerful creative flexibility
Connected via the Link Connection (In/Out jack on the MiCreator Studio)
Record high-quality audio for video projects and more
Connect a second pair of headphones via the built-in headphone jack

Cubase LE

free Steinberg software included

Cubase LE is the perfect introduction for aspiring music producers and composers. It's a powerful yet easy-to-use DAW that gives you everything you need to create professional music. With its intuitive interface and comprehensive features, Cubase LE is the perfect way to learn the basics of music production. Cubasis LE for iOS devices is unlocked when MiCreator Studio is connected to an iOS device.

WaveLab Cast

free Steinberg software included

WaveLab Cast is the ultimate audio production and podcast software for Mac and Windows. With its powerful features and intuitive user interface, WaveLab Cast makes it easy to create professional audio content. Whether you are an experienced podcaster or just starting out, WaveLab Cast has everything you need to create great sounding podcasts.

Technical Specifications
Digital Resolution: max 48kHz/24-Bit
Digital Connector: USB-C - USB Audio Class 1.0/2.0 compliant
Directional characteristic: Cardioid
Frequency range: 20 Hz - 20 kHz
Sensitivity:- 35dBFS/Pa (low gain)/-15dBFS(high gain)
Hardware Gain Switch: 0dB (low)/20dB (high)
Equivalent noise level: 22 dB SPL (A) (high gain)
Max SPL: 130 dB SPL (low gain)
Output Power: 45mW (32Ohm Load)
Dynamic Range: 89 dB(A)
In/Output TRRS: for instrument cable, 2nd headphone or MiCreator Satellite or Y-Lav
Dimensions: 155 x 60 x 37 mm
Weight: 370g

Notes: Custom backpack for the BOSS RC-505mkII and RC-505 Loop Stations

Transport your RC-505mkII or RC-505 in style with the CB-RC505, a premium backpack-style carrying bag for BOSS's popular tabletop Loop Stations.

The slimline design is light and easy to carry, while the plush internal padding fully protects your RC when you're on the move. There's also a sub-compartment for stowing a laptop or tablet, plus a large outside pocket for essential looping accessories.

Creative Magic Everywhere You Go

The RC-505 series eliminates the need to carry lots of additional gear, thanks to its onboard multi-effects, integrated mixing features, and versatile connectivity options. This bag's slim design is just right for users of the tabletop Loop Station, trimming unneeded bulk while providing a protective home for the instrument and core items you need to create and perform.

Smart Onboard Storage

The outside pocket on the CB-RC505 is big enough for a mic, headphones, AC adaptor, and cables, standard accessories for beatboxers and other vocal-based loop performers. And with the flat pocket inside the main compartment, you can expand your creative setup with a laptop or tablet. If you're a looping instrumentalist who needs more room for foot pedals and other external gear, the CB-BU10 Utility Gig Bag is an ideal option.

Premium Construction

The CB-RC505 is built to last with quality materials and construction throughout. The water-resistant nylon exterior is rugged and protective, and there are two thick rubber feet for impact protection when setting the bag on the ground. The padded top handle is comfortable to grab and reinforced for years of travel, and you can easily hide the backpack straps in dedicated pockets when they're not needed.

Custom backpack for the BOSS RC-505mkII and RC-505 Loop Stations
Rugged construction with water-resistant nylon
Plush interior with thick padding
Hideaway backpack straps and handle with comfortable padding
External pocket for a microphone, AC adaptor, and other accessories
Slim sub-compartment for a laptop or tablet
Thick rubber bottom feet
Heavy-duty zipper with custom BOSS pull

Specifications

Compatible Models: RC-505MK2, RC-505
Main Material: Nylon cloth (front cloth), Polyester (inner cloth)

Size & weight
Dimensions (excluding protruding parts):
470 (W) x 310 (D) x 185 (H) mm
18-9/16 (W) x 12-1/4 (D) x 7-5/16 (H) inches
Weight: 1.28 kg / 2 lbs 14 oz

Notes: The Morphor Distortion - LED Based module is a compact and characterful analogue clipping distortion module. Loosely based on the legendary MXR distortion circuit this module is perfect for adding some extra crunch to your patches.

With CV-controlled gain setting, three distortion modes and a dry/wet mixing control, this module gives you lots of options to spice up your sound without taking up too much space. Internally the clipping is performed by LEDs which are also shown in the front of the module, so you can see your sound getting destroyed with your own eyes.

Weight: 53 g
Dimensions: 128.5 × 20 × 40 mm
Width: 4 HP

Notes: The Morphor VCF Multimode is an intuitive, no nonsense 8HP fully analogue filter module. Featuring a dedicated lowpass and highpass filter core.

To shape the sound exactly the way you want, both filter sections have a cutoff frequency control over the whole audible frequency range through a knob and bipolar CV jack. Additionally, resonance control and a switchable pole selection are available.

The second output acts as both a bandpass and highpass output, depending on the position of the BP/HP mixing knob. Combining all these features results in an easy-to-use but flexible module to perform your unique filter needs.

Weight: 110 g
Dimensions: 128.5 × 40.6 × 40 mm
Width: 8 HP

Notes: CONTROL PATH is an all in one voice dynamics module that helps build full voices quickly. It contains two analogue envelopes with velocity cv, and one VCA. In a typical voice patch the left envelope will control a filter and the right envelope will be the voice VCA. Velocity control is provided for each envelope and delay front panel trimmers are used to compensate for any miss match between incoming gate signal and velocity CV timings. Envelope cv outs are 0-5V, Velocity cv ins are 0-5V.

Size: 8HP - Depth: 40mm / 1.5"
Power: +12V 50mA / -12V 55mA

Notes: Great value from this versatile percussion module, built around a noise generator and four linked envelope generators, each with its own VCA. Generate hi-hats, envelopes, shape drums or create modulation sequences.

Supplier's Notes:
Ricochet is a compact, fully analogue module featuring four interconnected decay envelopes, each with its own VCA and an integrated noise generator.

The module's design is inspired by the way skipping stones bounce on the water, creating a versatile tool for crafting percussive sounds.

The exponential envelopes are specifically designed to generate dynamic percussive tones. The unique linking function connects the end of one envelope's decay to the trigger of the next, enabling the subsequent envelope to activate once the previous one ends. This innovative feature allows you to create ratcheted envelope.

A front-panel trimmer lets you adjust the threshold for triggering subsequent envelopes, while a rear header enables connecting two Ricochet modules together, or linking the last envelope to the first. This feature transform the Ricochet to a weird sequencer where the steps length depend of the decay times.

Since Ricochet is fully analogic, trig inputs are velocity-sensitive, responding to a standard gates but also allowing attenuation to modify the envelope's velocity (you can play with the dynamic of your sound by attenuating the trigg input. Ricochet is also perfect to play with drum pads).

Each VCA features a gain control that can be pushed to achieve subtle saturation.

All envelopes and VCAs have separate outputs, but there are also mixed audio and envelope outputs. When an individual output is connected, it is removed from the mix. The decay modulation inputs are normalized between each other.

Last but not least, an analogue noise generator is normalised to the first input, so you can use ricochet on it's own to create hi hat kind of sounds

Main features:

- Fully analogue design so everything is responsive to the amplitude
- Unique linked envelopes feature
- Compact 4 envelopes 4 VCAs module
- Linkable to a second ricochet or looping back the last envelope to the first one

Some applications:

- Envelope generator
- Drum shaper
- Hi-hat
- Clap envelope shaper( with short ratcheted envelopes)
- Envelope sequencer
- Trigg delay
- Burst generator

Technical details:

- Fully Analogue design
- 14hp
- Skiff friendly
- Reverse power protection

Notes: 2mm thick aluminium panel, in bath-anodized finish, with high-quality light-grey printing.

Notes: Lush analogue EQ switchable between tilt and Baxandall high-shelf configurations.

Perform a variety of mixing and sound design duties ranging from subtle brightness and clarity adjustments to low-end rumble removal, boosted low-pass filtering and sweep EQ.

In the default tilt mode, turning the control knob clockwise simultaneously boosts treble and cuts bass. Turning anti-clockwise boosts bass and cuts treble. These boosts and cuts are pivoted around the mid-range. With the control knob at 12 o'clock the frequency response is neutral.

With Baxandall high-shelf mode enabled, turning the control knob clockwise past 12 o'clock introduces and gentle high-shelf EQ weighted around the upper mid-range. Turning the control knob anti-clockwise results in a wide high-shelf cut with subtle bass and mid-range adjustments.

Patching the channels in series allows for radical sound shaping and band-pass responses. Each channel provides up to +/- 8db of low and high-frequency gain control, summing into a low noise output stage. Hot input signals over 15vpp are saturated by active Zener diode clipping.

Features

Precise voltage control of EQ tilt and shelf
Seamless switching between EQ modes
High-quality components used throughout

Specifications

Intellijel 1U format
Width: 18HP
Depth: 32mm
Power requirements: ~60mA +12V/~58mA -12V
Control voltage range: 0-8V
Impedance Input: 100K / Output 1K

Notes: Transpos lets you transpose three CV channel with a single source.

Adder:

The voltage of each CV input can be varied by plus or minus two octaves depending on the switch and the potentiometer of each channel. Transpos uses precision regulators: for example if we increase by a fifth with the switch on "+" we reduce it by a fifth when we pass on "-".

Transposer:

The 1V/o CV input will influence each of the three channels. By turning the CV potentiometer you can globally increase or decrease the transposition of the three channels at the same time.

Dimensions
8 HP
40 mm deep

Current Draw
70 mA +12V
70 mA -12V
0 mA 5V

Notes: Mûmack is built from a temperature-stabilized analog source producing the three classic waveforms: triangle, saw, rectangle. This basic signal can be altered or enriched in several ways, which can be combined with each other, and associated with one VCA per mode.

Peak Compressor:
In the central position the signal is not modified. Turning the potentiometer to the right or to the left will compress the signal positively or negatively. It is this signal that will then feed Usual, Mûm and Hack. An LFO is dedicated to the compressor, controllable in speed and amplitude. A CV input with attenuator can also control the compressor.

USUAL:
The three waveforms are freely mixable, a CV input and a potentiometer can change the shape of the rectangle wave (PWM). The compressor intervening upstream, it can strongly influence the final form and the amplitude of USUAL. This produces complex analog waveforms, moving in time with the LFO or the CV input. The linear potentiometer makes it possible to mix the signal with the others, and to dose the volume of the direct output. The rotary potentiometer acts as an attenuator for the VCA input.

MÛM:
The Waveform potentiometer move the waveform of Mûm continuously from a attenuated triangle to a more pronounced triangle, then to a sinusoid and finally to a square wave. An LFO allows you to add a vibrato adjustable in speed and amplitude. The linear potentiometer makes it possible to mix the signal with the others, and to dose the volume of the direct output. The rotary potentiometer acts as an attenuator for the VCA input.

HACK:
Mûm's signal is taken up in a Wavefolder + compressor. Depending on the settings of the Peak compressor, and the three LFOs, we obtain complex, moving, organic waveforms. Again the linear potentiometer allows to mix the signal with the others, and to adjust the volume of the direct output. The rotary potentiometer acts as an attenuator for the VCA input.

ALL:
The three channel (Usual, Mûm, Hack) are mixed and brought together in a single output. The output volume is adjustable and a CV input with attenuator works like a VCA.

MIXER & VCA
The voltages produced by Mûmack, as is the case with many analog VCOs, can be high. The mixer allows them to be attenuated if necessary. Each of the three channels, and the product of the three, can be controlled by the VCA, with attenuator. The VCA is designed to add distortion at high values. The mixer is exponential for more subtle adjustments in low values.

Dimensions
30 HP
40 mm deep

Current Draw
155 mA +12V
155 mA -12V
0 mA 5V

Notes: Engineered with a 40mm speaker diaphragm made from stiff bio-cellulose to reduce distortion and increase transparency. Tuned for a balanced, accurate sound. Balanced sound - Bio-diaphragm.

Notes: This stand its part of a new concept in COVERUP. With differents parts, you can use to put on multiple synths, including big devices, until now, not possible with the other stands.

You can configure your setup with you like more, with two big devices, or three medium devices. Easy to ensamble, very light to move from your studio to live. Just you need 1 minute to arm and start to playing.

Your setup of synthesizers and studio equipment can change permanently and with it also the position on the work table.

Taking this into account, CoverUp developed a 3-level support, which can be set up in different ways depending on the number of machines that we are going to place and their size.

In the triple stand configuration (using all 4 parts), 3 20cm machines can be placed. deep and a maximum height of 7cm.

This space is enough for much of the hardware available today.

The triple bracket parts are assembled with screws (included) using a universal socket that holds them together firmly.

In turn each part can be used as a simple support. It is only enough to separate the parts by removing the screws and use each part as it suits us.

Each part has rubber feet underneath, so that the support does not slip and is firmly supported.

Both halves of the triple support are linked with wooden rods at various points to give it lateral stability.

The design contemplates space for the rear connectors of each equipment, so that none of them are obstructed by the support.

Measures:
Depth: 58cm
Height: 41cm
Width: 34cm

Notes: The AKAI APC 40 MK2 Controller Stand is a highly versatile and practical accessory designed specifically for the APC 40 MK2 MIDI controller. This stand offers a host of features that make it an excellent choice for DJs, musicians, and producers who require an ergonomic, stable, and portable solution.

The stand is carefully crafted to provide an optimal working position for the controller, allowing for comfortable access to all knobs, faders, and buttons. Its ergonomic design ensures that you can use the controller for extended periods without straining your wrists or arms.

Stability is a key feature of the AKAI APC 40 MK2 Controller Stand. It is built with a sturdy and durable construction, ensuring that your controller remains securely in place during intense performances or studio sessions. You can confidently engage with the controls, knowing that the stand will provide a reliable platform.

Additionally, this stand excels in terms of portability. It features a lightweight and compact design, making it easy to transport from one location to another. Whether you’re going to a live gig, a studio session, or simply moving between different workspaces, the stand’s portability ensures that you can conveniently take it with you without any hassle.

In summary, the AKAI APC 40 MK2 Controller Stand is a superb product that combines ergonomic design, stability, and portability. It offers a comfortable and accessible platform for your APC 40 MK2 controller, making it an ideal choice for DJs, musicians, and producers who value convenience and performance.

Notes: The AKAI APC 40 MK2 Controller Stand is a highly versatile and practical accessory designed specifically for the APC 40 MK2 MIDI controller. This stand offers a host of features that make it an excellent choice for DJs, musicians, and producers who require an ergonomic, stable, and portable solution.

The stand is carefully crafted to provide an optimal working position for the controller, allowing for comfortable access to all knobs, faders, and buttons. Its ergonomic design ensures that you can use the controller for extended periods without straining your wrists or arms.

Stability is a key feature of the AKAI APC 40 MK2 Controller Stand. It is built with a sturdy and durable construction, ensuring that your controller remains securely in place during intense performances or studio sessions. You can confidently engage with the controls, knowing that the stand will provide a reliable platform.

Additionally, this stand excels in terms of portability. It features a lightweight and compact design, making it easy to transport from one location to another. Whether you’re going to a live gig, a studio session, or simply moving between different workspaces, the stand’s portability ensures that you can conveniently take it with you without any hassle.

In summary, the AKAI APC 40 MK2 Controller Stand is a superb product that combines ergonomic design, stability, and portability. It offers a comfortable and accessible platform for your APC 40 MK2 controller, making it an ideal choice for DJs, musicians, and producers who value convenience and performance.

Notes: Your AKAI deserves to be in a comfortable position to enjoy it. That is why CoverUp have designed this stand so that in your studio, you have the best ergonomics and can make music without thinking about anything else.

Notes: The double stand is intended to house two Behringer synthesizers, with the ability to improve the operating position on both.

At the same time, it saves a lot of space on the surface, ideal for optimizing the space in our studios.

The stand includes rubber feet so it won’t scratch or slip.

It is compatible with Model D, K2, Pro 1, Neutron, Cat, Wasp

Notes: One of Native's latest creations has its ergonomic stand ready for studying.

Now you can have greater comfort, view your screen and all the equipment thanks to this custom-designed stand.

At the base, there are 3m rubber feet so that the equipment does not move at any time.

Weight: 0.1 kg
Dimensions: 5 × 5 × 1 cm

Notes: The ideal support for your three Boutique synthesizers.

To use them in a comfortable and ergonomic position, which in turn saves space.

Specially designed taking into account the need for space for wiring and rear connectors.

On the support faces, each support has a recess to place silicone feet and prevent the equipment from slipping or scratching.

Includes the two side supports, the rods and the silicone feet

Notes: Triple support for the entire Korg Volca line (Beats, Kick, Sample, FM, Keys, Bass, Drum, Modular, Mixer)

Save space in your studio and operate your synthesizers more comfortably.

The brackets fit directly into the Volca without the need for screws or moving parts. This makes them easy to transport and set up for those who go out and play with their Volca.

On the bottom, each foot has silicone legs to prevent them from scratching or slipping.

The pictures show red, but the colour is black.

For up to 3 Korg Volca devices
Made of biocompatible PLA plastic
Connection of the side parts by means of wooden rods
Dimensions (W x D x H): 196 x 246 x 271 mm

Suitable for:

Volca Beats
Volca Drum
Volca Bass
Volca Keys
Volca FM
Volca Kick
Volca Nubass
Volca Modular
Volca Sample
Volca Mix

Notes: CoverUp designed two ergonomic support models for the OP-1: Studio and Live versions.

The Studio support has a higher incline and is elevated. This is ideal for seated use, improving screen visibility, and the height allows it to be positioned even behind other desktop equipment.

The Live version of this support has a slight incline and is intended for use in a live or standing situation.

Both supports have rubber feet to prevent slipping and are adorned with two well-known characters that appear on the OP-1.

***Please note: The OP-1 is not included, it is shown in the photos for demonstration purposes only. ***

Notes: ***B-STOCK: Without original box, product has light surface marks but otherwise in perfect working condition.***


The Sonicware SmplTrek is a compact and powerful sampler that opens up endless creative possibilities for music producers and performers alike. With its intuitive interface and versatile feature set, the SmplTrek is the perfect tool for capturing and manipulating audio on the go.

The SmplTrek boasts a wide range of sampling and synthesis capabilities, including built-in effects, a step sequencer, and a wide variety of sound-shaping tools. It's a powerful and versatile instrument that's perfect for creating beats, melodies, and textures for your music.

To ensure the longevity and protection of your device, Decksaver has designed a custom-fit cover made from super-durable polycarbonate material. Decksaver's team of experts has spent many hours researching and testing to ensure that these covers provide the highest degree of protection against dust, debris, spills, and other potential hazards.

The Decksaver cover for the Sonicware SmplTrek is an essential accessory for any musician who values their equipment. Not only does it provide top-tier protection, but it also adds a sleek and professional look to your setup.

With this cover, you can rest assured that your SmplTrek will stay safe and secure, allowing you to focus on making music without any worries.

Dimensions

Weight: 0.70 kg
Length: 18.1 cm
Width: 15.3 cm
Height: 2.3 cm

Material: Smoked clear polycarbonate.

WARNING: When your Decksaver cover is in place, please ensure that your equipment is kept away from direct and high heat sources, such as radiators, fires and sunlight.

Notes: ***B-STOCK: Box opened, product in perfect working order***


The Arpopone from LepLoop is a little synth-voice for generating a melody or bass line and a chord section at the same time. It is based on analog ramp dividers of which each one generates a voltage ramp starting from a master clock that can be internal or external.

Trig1 and Trig2 potentiometers set the number of clock pulses.

With the Trig Mix switch it is possible to select between a single trigger (1 or 2) or both (1+2) to advance the scales.

The Scale Step potentiometer sets the number of steps for the two scale generators.
In the mixer section, the two scales are summed together to obtain a more complex pattern. The amount of each scale can be set by two controls and can be positive (ascending scale) or negative (descending scale).

With the VCO Pitch knob, the melody can be transposed while maintaining the same interval between notes.

The note generated by the VCO is fed to a chain of dividers to obtain four sub harmonics of the original note. One of these is the bass section with its own filter and envelope, the other three form the chord section with their envelope.

The two envelope sections are identical, both have a selector for different trigger sources:

Trig1 & Trig2: the envelope starts at the flash of the green LED (bass) or yellow LED (chord)
SB1 & SB2: the envelope starts at the first step of Scale1 (bass) or Scale2 (chord)
White & Blue: the envelope follows the intensity of the white LED (bass) or the blue LED (chord). Except for this setting the envelope length is set by the two controls Bass ENV and Chord ENV. Additionally, an EXT CV input allows to provide an external envelope.
The bass channel is passed through a resonant low-pass filter with Cutoff and Resonance control.

Finally the Bass and Chord channels are mixed together. The output level is set by the Bass LEV and Chord LEV controls.

Notes: The latest update of Arturia's legendary plugin collection, featuring 39 instruments, three expansion packs and over 9,000 presets. New instruments include CP-70 V, MiniFreak V, Acid V and three Augmented collections.

Supplier's Notes:
V Collection X

Reference instruments for music makers
A premium suite of software instruments for unparalleled sonic exploration; from evocative emulations and hybrid synth engines, to authentically modelled keyboards and beautifully captured acoustic sounds - enhanced for today's production workflow.

This is V Collection X

Immerse yourself in an unparalleled music-making experience with iconic sounds and essential tools to suit your style, performance needs and production workflow. 39 instruments, 3 exclusive expansion packs, thousands of world-class presets - 1 canvas for infinite sonic exploration.

The ultimate selection

A hand-picked, expertly-engineered suite of instruments combining timeless sonic craft with cutting-edge enhancements that seamlessly integrate with demanding production workflows. The most iconic synths, blissful keyboards, evocative hybrids and faithfully captured acoustic instruments for endless inspiration, vivid composition and boundless play.

10,000+ presets

Find the crucial mix-finishing sounds you need in a few clicks with V Collection X's expansive library of expertly-designed sounds, complete with easy browsing. Tap right into any style, any instrument, any time.

Easy to use

You don't need to be an expert to enjoy professional sound. The instruments in V Collection X are designed with accessibility in mind, equipped with intuitive interfaces, interactive in-app tutorials, and intelligent features that deliver electrifying results without hassle.

Perfected for you

High-performance features that you can count on, premium sound quality you deserve; V Collection X is the result of over 20 years of engineering innovation, musical exploration, and a passion for audio excellence and expressivity.

39 Software titles

Augmented WOODWINDS
Augmented GRAND PIANO
Augmented BRASS
Augmented STRINGS
Augmented VOICES
Korg MS-20 V
SQ80 V
CS-80 V
Prophet-5 V
Prophet-VS V
Piano V
Analog Lab V
Vocoder V
Jun-6 V
OP-Xa V
Mellotron V
Synthi V
CZ V
CMI V
Clavinet V
Acid V
MiniFreak V
CP-70 V
DX7 V
Buchla Easel V
Synclavier V
Emulator II V
B-3 V
Mini V
Stage-73 V
Matrix-12 V
Farfisa V
Solina V
SEM V
Jup-8 V
ARP 2600 V
VOX Continental V
Wurli V
Modular V

Platform specifications

Windows

Win 10+ (64bit)
4 GB RAM
4 cores CPU, 3.4 GHz (4.0 GHz Turbo-boost)
32GB free hard disk space
OpenGL 2.0 compatible GPU
ARM processors not supported on Windows

Required configuration

Works in Standalone, VST, AAX, Audio Unit, NKS* (64-bit DAWs only).

Apple

Mac OS 11.0+
4 GB RAM
4 cores CPU, 3.4 GHz (4.0 GHz Turbo-boost) or Apple Silicon CPU
32GB free hard disk space
OpenGL 2.0 compatible GPU

Work with ASC

An elegant and simple solution to help you install, activate, and update your Arturia software instruments.

Notes: ***B-STOCK: Box opened, product in perfect working order***


A LS1lightstrip but in THREE fat dimensions!

A matrix of awesome and a powerful and unique CV controller for your system.

LP1lightplane is an expanded, tri-dimensional LS1 lightstrip. The same functions are exposed on either axis plus pressure (z) for three times the fun!

Notes: The highly coveted Octave Clang has made a triumphant return to Death By Audio's Queens workshop. Long presumed extinct, the OC was never really gone, merely in a state of hibernation-evolving, refining, and enhancing its already extraordinary sound.

In the decade since it disappeared, Death by Audio have revisited the original Clang circuit, sculpting it into something better-a more ferocious, menacing, and thunderous force that is as usable as possible for today's musicians.

Embraced by professionals and punks alike, the vintage Octave Clang was created to unleash distinctly unconventional tones that captivated the senses. In this, it succeeded, but many users found it difficult to tame. Today, Death By Audio have refined and extended the range of the original controls, added a foot-switchable octave, and did some under-the-hood supercharging.

The resulting circuit is an insane yet versatile beast, empowering you to easily sculpt discordant ringing drones, visceral octave scrapes, and ground-shaking distortion. The revitalized Octave Clang is primed and ready to destroy!

Controls

Bypass (Left Footswitch): Turns the Octave Clang on and off (red LED).
Octave (Right Footswitch): Toggles the Octave Up mode (yellow LED). The yellow LED stays on/off when the pedal is bypassed to indicate if the Octave Up is engaged.
Volume: Controls the output level. Goes from totally silent to extremely loud. When set above your normal volume, it propels your chain into overdrive
Gain: Sets the gain of the Octave Clang. This can (and will) drive the rest of the circuit into overdrive and fuzz. Can provide up to +39dB of gain.

Tone: A powerful pre-gain tilt EQ, this control adjusts the amount of highs and lows going into the rest of the circuit. This can make the octave and fuzz react very differently. Overloading the lows yields a larger, more blown-out sound while overloading the highs gives a more cutting and clear sound.

Bias (Internal): Allows misbiasing the distortion circuitry. Leave this control in the middle (5-6) for standard functionality, or turn it left or right to skew the character of the distortion to a rougher sound.
Access this control by removing the back plate of the Octave Clang.

Specifications

Dimensions: 4.8" x 3.7" x 2.1" (including hardware).
Weight: 11.5 oz.
Power: The Octave Clang is powered by a standard 2.1mm 9V DC adapter with a centre-negative polarity. Isolated power supplies are recommended. It is also possible to use the Octave Clang with a 9V battery (not provided). When not using a battery, the internal battery snap should be attached to the corresponding battery snap holes on the board. This will prevent the contacts from shorting out against the circuitry. Do NOT leave the battery snap floating inside the pedal when not using a battery.
Current Draw: 10 mA

Notes: ***B-STOCK: Box opened, product unused & in perfect condition***


Equipped with the same ESS Sabre32 Ultra DAC Technology found in audio interfaces costing thousands, the M4 delivers an astonishing 120 dB Dynamic Range on its main outputs. ESS converters also drive the headphone output, which rivals dedicated headphone amplifiers costing hundreds. Ultra-clean preamp circuits produce a measured -129 dBu EIN on the mic inputs. Capture and monitor your audio with pristine clarity.

The M4 provides best-in-class speed for monitoring live inputs (mic, guitar or keyboard) through your computer, thanks to MOTU's expertly engineered USB drivers, which deliver class-leading, ultra-low 2.5 ms Round Trip Latency (at 96 kHz with a 32 sample buffer).

When recording and mixing, nothing is more critical than achieving optimum levels. The M4 is the only audio interface in its class with a full color LCD featuring clear, detailed level meters for all inputs and outputs. Enjoy professional-level volume control and feedback to get your sound just right.

The M4 driver provides convenient loopback channels to your host computer, so you can easily route computer output back to the computer, where you can mix it with live mics and/or guitar inputs from the M4 in your host software for live streaming or podcasting. Streaming and podcasting has never been easier and better-sounding!

Decades of award-winning product engineering for hit songs, mega tours, primetime shows and blockbuster movies goes into every MOTU audio interface.

Notes: The VESA Mount is a sturdy adjustable mount for products fitted with VESA mounting screws, such as the RODECaster Pro II and RODECaster Duo. It features a locking ball head that can rotate 360 degrees for easy manoeuvring of the device in any orientation.

The mount attaches to any standard microphone stand or studio arm, and is the perfect way to position your device in a range of scenarios.

Note - not compatible with the original RODECaster Pro.

Suits both 100 and 75mm VESA mounts
360-degree ball head mount
Easy-to-use cam to lock in any position
Attaches to any standard microphone stand or sudio arm

Mechanical specifications

Weight (grams): 400g (including screws)
Dimensions (millimetres):
Length: 140
Width: 140
Height: 90
Compatible RODE Products: RODECaster Pro II, RODECaster Duo

Notes: ***B-STOCK: Box opened, product in perfect working order***


The latest and greatest version of one of the most popular microphones around. XLR and USB connections both offer warm sound suitable for vocals, instruments and podcasting.

Supplier's Notes:
The NT1 5th Generation is a revolutionary studio condenser microphone that fuses the classic sound signature of the iconic NT1 with cutting-edge, next-generation technology. It features RODE's groundbreaking (patent-pending) Dual Connect output, offering both XLR and USB connectivity for incredible versatility, a world-first "unclippable" 32-bit float digital output, advanced digital signal processing, and more, all while delivering the same warm, silky character, extremely low noise, and high SPL handling that the NT1 is renowned for. The NT1 5th Generation is a true studio workhorse that excels on everything from vocals and speech, to guitar, piano, drums and percussion - the ultimate studio microphone.

The Iconic Original Studio Microphone, Reborn

The NT1 5th Generation is the latest evolution of the iconic NT1. First introduced in 1991, the NT1 is the world's most popular studio microphone, renowned for its warm, classic sound and incredible versatility. The NT1 5th Generation takes the much-loved and respected core of the NT1 and introduces state-of-the-art features while preserving the legendary sound quality that made the original the go-to microphone for countless creators. A perfect marriage of tradition and innovation.

Game-changing Connectivity

Featuring RODE's groundbreaking, patent-pending Dual Connect output, the NT1 5th Generation can either be connected to an audio interface or mixer via XLR or directly to a computer via USB for studio-grade, plug-and-play recording. Unprecedented flexibility for any studio setup.

Classic Sound on the Cutting-edge

The NT1 5th Generation delivers the same warm, silky character, extremely low noise, and high SPL handling capability that the original is revered for, with improved circuitry for even lower self-noise - an astonishingly low 4dBA, making it the world's quietest studio condenser microphone. When using the XLR output, it delivers the rich, classic studio condenser sound you know and love from the NT1. When using the digital output, you get this same sound plus a slew of cutting-edge features to further enhance your audio for recording pro studio sound directly into your computer.

The Digital Studio of the Future

The NT1 5th Generation features a professional-grade audio interface built into the microphone, which is perfectly optimised to preserve its pristine audio fidelity and also offers a range of highly innovative features for enhanced sound, including the ultra-low-noise, high-gain Revolution Preamp™, high-resolution (192kHz) A/D conversion and advanced digital signal processing. This is so much more than just a studio condenser microphone, it's an all-in-one digital recording solution.

The "Unclippable" Microphone

The NT1 5th Generation features a world-first 32-bit float digital output - a revolutionary recording format that allows you to record everything from a whisper to a scream, the softest guitar to the loudest drummer without having to worry about setting your gain - simply adjust your audio after recording and all the dynamics of your performance will be maintained, with zero risk of clipping or distortion. Gamechanger.

Versatility Like No Other

With its smooth frequency response, extremely low noise, high SPL handling, flexible connectivity options and powerful digital capabilities, the NT1 5th Generation offers versatility like no other studio mic. It excels in any recording application, from vocals and speech to guitars, drums to piano, and can fit into any workflow, from a solo bedroom recording setup to a professional studio.

Craft Your Sound

Craft your sound with advanced APHEXr audio processing, driven by the NT1 5th Generation's powerful on-board DSP. Add compression, a high-pass filter, noise gate, and the legendary APHEXr Aural Exciter™ and Big Bottom™ to your audio with ease using the free RODE Connect and RODE Central companion apps. Dial in the perfect sound with the touch of a button using the intuitive VoxLab™ editor or fine-tune each processor using the advanced editor.

Premium Components, Built to Last

Made from premium components, the NT1 5th Generation is built to the highest standard in RODE's state-of-the-art manufacturing facilities in Sydney, Australia. The HF6 capsule is precision manufactured to sub-micron tolerances to ensure the utmost consistency in tonality and frequency response and is internally shock-mounted for minimising external vibrations. The body is machined from rugged aluminium and is available in black or silver, with high-grade finishes that are extremely resistant to scuffs and scratches, ensuring the NT1 5th Generation is ready to take on the rigours of recording day in, day out.

Everything You Need to Start Recording

The NT1 5th Generation comes with everything you need to start recording in the box, including XLR and USB cables, and a studio-grade shock mount and pop filter for minimising unwanted artifacts in your recording caused by plosives, knocks and bumps.

Unlock More Creative Potential with the RODE App Suite

The NT1 5th Generation is compatible with a range of free RODE apps, including the RODE Central companion app, RODE Connect podcasting app and UNIFY streaming app, all of which allow you to configure settings, access the advanced DSP, update firmware and more.

Specifications

Acoustic & Electrical Specifications

Acoustic Principle: Pressure gradient
Active Electronics: JFET impedance converter with bipolar output buffer
Capsule: 1.00"
Polar Pattern: Cardioid
Address Type: Side
Frequency Range: 20Hz - 20kHz
Output Impedance: 100O
Maximum SPL: 142 dB SPL
Equivalent Noise (A-weighted): 4dBA
Sensitivity: -32 dB re 1 Volt/Pascal (25 mV @ 94 dB SPL) +/- 2 dB @ 1 kHz
Analogue Power Requirements: Via XLR: P48
Analogue Output Connection: 3-pin XLR

Digital Specifications

Digital Power Requirements: Via USB: 5V
Digital Output Connection: USB-C
Bit Depth: 24-bit / 32-bit floating point
Sampling Rate (kHz): 48 / 96 / 192
Processing: APHEX digital signal processing (only available at 48kHz / 24-bit)
Minimum OS Requirements: Windows 10 Mac OS 10.15

Mechanical Specifications

Weight (grams): 308

Dimensions (millimetres):
Length: 52
Width: 52
Height: 189

Box Contains

1 x NT1 5th Generation
1 x SC29
1 x XLR-6
1 x SM6

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Third-generation version of NI's outstanding MIDI controller keyboard updates what was already a winning formula. Here in the 49-key version, offering outstanding control of software and immense playability.

Suppliers notes:
An intelligent keyboard controller in three size options, designed to be at the core of any studio. Virtual instruments meet the real world with seamless Kontakt integration and a high-resolution screen. Plus, polyphonic aftertouch delivers intuitive parameter control across all three models, in combination with weighted, hammer-action keys in the S88. All contained in an overhauled design that looks incredible and is built to last.

Dimensions: 802.2 × 323 × 86 mm
Weight: 5.5 kg

Thousands of instruments made real Virtual instruments are brought to life in a genuinely immersive experience. Whatever you're playing, get in-depth control and integration through advanced NKS technology. Find sounds quickly with intuitive on-screen navigation. Then fluidly adjust and play them thanks to intelligent auto-mapping. This unparalleled direct connection means you can play completely real-feeling Kontakt instruments, plus thousands of partner sounds, instruments, and effects, with no interruptions to your workflow.

Polyphonic aftertouch

Take expression one-step further and instinctively control parameters with the slightest pressure on each individual key. Modulate cutoff, pitch, vibrato, and much more without reaching for an extra control. All three models have an industry-leading keybed, developed in collaboration with Fatar to deliver the best possible polyphonic aftertouch experience.

Hardware specification

1 high-resolution colour screen with glass surface (1280 × 480)
CNC machined, bead blasted and anodized aluminium, 8 × encoder caps, 1 × 4D encoder cap, 2 × wheels (pitch and mod)
RGB illuminated pitch and mod wheels
New button-islands that form a continuous dustproof control surface and are grouped by function

Included software

Komplete Select
Komplete Kontrol Software
Stradivari Cello
Guitar Rig LE
Elements Suite
Hypha

System requirements

MIDI 2.0 compatible
Intel Core i5, Apple M1 (and equivalent or higher)
macOS 13 (Ventura) or higher (compatible with macOS 12 in MIDI
mode)
Windows 10 (latest service pack) or higher
8 GB RAM
An internet connection and a graphics card that supports Direct 3D 11.1 (feature level 11_0) or higher are required to download and activate this product. Once installed and activated, the product can be used offline.

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


An advanced, feature laden, stereo overdrive and distortion pedal with a broad range of options and controls. With the Operation Overlord - whether you play keyboards, guitar, bass or pretty much any electronic instrument - dialling in great drive sounds is fast and fool-proof. Active, Treble, Mid and Bass controls, a foot-switchable Boost mode and a dry blend deliver superlative sound shaping. It even features two independent channels for use with stereo setups. Whatever your rig, the Overlord is your indispensable ally.

Notes: The "uMM" combines a MIDI merger and two independent THRU distributors in a module that is only 4 HP wide. All sockets on the module are in MIDI TRS-B format.

At the heart of the two-input MIDI merger is a small, powerful ARM processor with plenty of buffer memory. Two MIDI streams are mixed to one output and can also be tapped via an additional second output. Two LEDs signal the operation of the merger: one LED indicates MIDI activity at the inputs, and a second LED warns of too much data at the inputs.

The second group of functions consists of two independent, separate MIDI THRU distributors. The MIDI data at the respective MIDI input can be picked up and distributed at the three THRU outputs. If required, a 1-to-5 distributor can be created from the two units by connecting an output of the left group to the input of the right group.

Features:

4x MIDI IN (TRS-B)
2x MIDI-OUT (TRS-B)
6x MIDI-THRU (TRS-B)
Powered via Doepfer connector

Notes: ***B-STOCK: Box opened, product in perfect working order***


Keyboard version of IK's three-oscillator, dual-filter analogue synth. Classy purist analogue tones with some nice modern features like a step sequencer and effects. Also available in a cheaper, capacitive keyboard version.

Supplier's Notes:
Next generation analog for everyone

UNO Synth Pro gives you the power to create nearly any analog synth sound you can imagine. With its unique dual-filter, 3-oscillator paraphonic design, 256 presets, 64-step sequencer, studio-grade effects, expanded connections and much more, UNO Synth Pro breaks new ground for music makers.

Available in two form factors to suit all players' needs- stage-ready with metal housing and premium keybed; or ultra-portable, USB-powered with capacitive keyboard- UNO Synth Pro offers everyone the next generation of analog sound design in a smart format that fits any space or budget.

3 analog oscillators offer continuously variable waveshape, including pulse-width modulation. Oscillators can be hard-synced for more harmonically-complex tones, and oscillator FM (frequency modulation) lets you shape everything from bell-like sounds to screaming industrial tones. UNO Synth Pro even includes ring modulation for wobbly, sci-fi sound, and a white noise generator for a wide range of percussive sounds and epic rises.

Recreate famous synth sound sources or forge entirely new ones - UNO Synth Pro has the tools you need.

In addition to the original UNO Synth's 2-pole OTA multimode filter, UNO Synth Pro adds a new 2/4-pole SSI LP filter with self-oscillation. The dual filters can be used in series or parallel, with invertible phase, for a total of 24 possible filter combinations.

In short, the UNO Synth Pro can recreate the filter sound of the most famous classic synths as well as deliver fresh new options to the limits of your imagination.

UNO Synth Pro offers 2 full ADSR envelopes, one dedicated to the filter and the other to amplitude, with both available as sources to modulate everything from oscillator pitch and waveshape to LFO speed or even other envelope stages.

2 LFOs (low-frequency oscillators) can create classic synth vibrato, wah and tremolo as well as do more complex modulations including audio range FM.

And a 16-slot modulation matrix makes routing all these a breeze. You can quickly and easily design even the most sophisticated modulation scheme, with both internal and external sources, including MIDI controllers.

IK's experience in modeling analog studio effects is decades long. For UNO Synth Pro, you'll find a super warm and organic true-analog overdrive, plus 12 studio-quality effects in three simultaneous slots: modulation, delay and reverb. External signals can also be routed through these effects, with pre-effects filtering for maximum flexibility.

UNO Synth Pro provides an enhanced version of the original's long-lasting capacitance-sensing keys along with pitch and mod strips for enhanced expression. And it adds firm-touch rubber pads for the control sections, plus LED-backlit indicators and an LED display for key information, making it easier than ever to use UNO Synth Pro live on stage or in deep programming sessions in the studio.

UNO Synth Pro offers 256 user-editable presets, each capturing the full state of the sound engine from oscillators to effects.

An onboard 64-step sequencer offers both step and real-time recording, with automation for up to 40 parameters, letting you create incredibly intricate and evolving soundscapes. You can even write CV and gate automation.

And a 10-mode arpeggiator makes it easy to create intricate patterns and runs plus a new "chord mode" that takes advantage of UNO Synth Pro's paraphonic design.

UNO Synth Pro offers two noiseless, balanced stereo outputs as well as headphone out, for superior audio quality in any situation.

USB and 5-pin DIN MIDI In and Out make it easy to integrate with other synths, Mac/PC and mobile devices, and its assignable CV/Gate connections lets UNO Synth Pro interact effortlessly with your Eurorack or other modular system.

And now, audio input allows access to the filter and FX section for external signals, in addition to the original thru-put for daisy-chaining multiple units together without using a mixer.

Free Editor

Free UNO Synth Pro Editor for Mac/PC and iPad now available for all purchasers to download. This gives you access to all the advanced features 'under the hood' to manage presets and to easily create your own directly from your computer. Full details on the editor here: https://www.ikmultimedia.com/products/unosynthpro/?p=editor

Software Promo
All purchasers of UNO Synth Pro can now claim 2 free software downloads from IK's SE or CE product range: AmpliTube 5, SampleTank

Dimensions:
Size (W x D x H): 55 x 30 x 7 cm, 21.65 x 11.8 x 2.75 in.
Enclosure: Metal/plastic
Weight: 5.8 kg, 12.8 lb
Power: Power PSU

Package includes:
UNO Synth Pro
1x Micro USB to USB Cable
Power Supply Unit

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Collabing with YouTube sensation Andrew Huang, Endorphin.es offer up this impressive multipurpose processor module. Building blocks of stereo filtering, compression, reverb and more offer huge creative potential.

Supplier's Notes:
In collaboration with Andrew Huang, based on his modern music production techniques, Endorphin.es developed a creative audio processor with multiple blocks that can be moved around in order to achieve different flavours for sound design.

Processing unit without fixed structure: intuitively create astonishing and ephemeral timbres, from atmospheric rumbles to heavy or distorted textures.
Creative stereo effect processor with delay, reverb, filter and distortion with quickly explorable routing chain with single button press.
New generation ARM Cortex - M7 processor with 96 kHz 32 bit internal processing.
Lush hall and whooshing reverse reverbs with audio freeze and pre-delay.
Sidechain audio ducking envelope available both internally and externally with additional one knob single band compressor.
Tap delay with maximum delay time up to 2.5 seconds, external clock input with onboard clock divider and 1v/oct time control.
8x oversampled distortion algorithm.
Pre- and post - VCA, tone and volume controls with extra gain.

Power consumption
135 mA +12V
35 mA -12V
0 mA 5V

Dimensions
16 HP
26 mm deep with power ribbon cable connected.

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Up to eight voices of digitally synthesised drums, percussion and synth sounds from this versatile module, featuring virtual analogue models as well as FM and wavetable options.

Supplier's Notes:
Flame "Fire" percussion synth module

The module is a full 8-way polyphonic drum and percussion synthesizer. It offers different digital synthesis algorithms, which can be distributed over 8 channels. The sound engine delivers virtual analog sounds as well as different digital percussion sounds, which are generated with FM, wavetable or virtual analog synthesis. It is also possible to create sim- ple monophonic bass or synthesizer voices.

During development, particular attention was paid to direct and simple usability with regard to live operation. The hardware essentially consists of two parts (which are deli- vered together). On the one hand there is the basic module with all controls, the display, connections for MIDI, 2x CV inputs and 5 audio outputs.

There is also a separate XFIRE I/O extension with sockets for the 16 analog trigger/gate/CV inputs and 3 additional audio outputs. Both modules are connected via a 60cm long ribbon cable. In this way, the XFIRE module can be installed anywhere else in the rack. The base module is therefore only 22TE wide and can also work alone without the extension as a MIDI expander.

A maximum of 8 audio outputs are available. A stereo pair (outputs 7+8), plus 6 additio- nal individual direct outputs. All outputs are freely configurable. Two pages with settings for panorama and volume are available for the stereo main out.

There is a gate/trigger input and a configurable CV input for each channel. Two additio- nal programmable CV inputs can be used for further controls. Regardless of the analog connection, the module offers full MIDI functionality. Two MIDI inputs and a MIDI output/softthru allow integration into an external MIDI setup. The firmware can be upda- ted via MIDI Sysex. The created KIT data can also be saved or exchanged.

Notes: ***B-STOCK: Box opened, light surface marks, product in perfect working condition ***


The DISTURBANCE is an extreme filter, flanger, and phaser with modulation like you've never heard before.

DISTURBANCE's controls allow for a wide range of sounds to be sculpted perfectly to your needs. The 'Tensity' knob changes the feedback amount and structure of all effects, with two totally different intensity options to choose from for each disturbing modulation. The Filter allows for deep swells and piercing resonance with highpass and lowpass options.

The Flanger creates a classic modulation sound with options for watery, multi-tap delay matrixes or a screaming flange with distorted feedback. Last but certainly not least, the Phazer mode is a psychedelic 8-stage phaser sound with options for mellow filtered scoops on one side and combination phaser/flanger on the other.

But that's not all - the pedal introduces a brand-new way to control an effect: The custom designed modulation core lets you pause the LFO where it stands and listen to the strange world of frozen modulation. Not only does this new system control its own sounds, the DISTURBANCE includes a CV OUT jack which lets the modulation control signal be sent to whatever device dares let it in.

Go forth and DISTURB and bend, break, and twist your sound!

Notes: ***B-STOCK: Box opened, product in excellent condition, no original internal packaging***


Intellijel has made the already awesome Thru Zero VCO Rubicon even better! In addition to the seven waveforms plus sub-oscillator of the first version, the second generation offers a new Warp stage, which generates a hybrid of complex pulse and other waves - you can even use external audio material. In order to keep results in the range of 10 Vpp, there is a wave folder called Squish. On top, the FM capabilities were expanded.

Notes: ***B-STOCK: Box opened, product in perfect working order***


Record. Mangle. Destroy.

Nebulae is a granular sampler and DSP platform. Its phase vocoder audio engine provides elastic audio, which can be time stretched, granularized, and mangled to no end. With independent control over pitch and speed, and granular controls such as overlap, window, and density, finding new sonic territory is only a knob turn away. Nebulae can use live audio input, a recorded buffer, or audio files as the source material for its powerful audio manipulations. The live input buffer can record up to five minutes of stereo audio at 48kHz, 24 bit. In addition, up to 75 MB of stereo audio can be loaded simultaneously through the USB port. No naming convention or special formatting necessary; just plug and play.

Nebulae lives a double life as an open source DSP platform with an extensive library of off the shelf alternate instruments. You can turn the module into a lush reverb, spectral delay, or tape-style looper simply by loading a new file onto the flash drive. Do you want to tweak one aspect of an existing instrument, even the default functionality? No problem. No prior coding knowledge is necessary to tweak and refine existing firmware to your liking or start with one of our templates. Alternate firmware files can be written with Pure Data, Csound, SuperCollider, and even bare-bones C programs.

Notes: ***B-STOCK: Box opened, light surface marks, product in perfect working condition ***


Inspired by Roland's TR-x0x sequencers, the Drum Sequencer brings that classic approach to Eurorack, offering a massive 16 trigger channels with gate and accent outputs, plus a CV/gate track for synths.

Supplier's notes:
X0X-style beat creation for modular systems - Erica's drum sequencer is based on the concepts of classic Roland TR rhythm composers. The module offers 16 trigger channels, twelve of which also feature accent outputs. Additionally, there is a CV and a gate track, meaning you can also notate a bass line or melody. The maximum pattern length is 64 steps. Extensive playback and random functions plus two LFOs help you with creating lively results. Large buttons provide a fantastic feel while programming patterns.

Notes: Gross, gritty, and dark industrial-strength voice on a swappable oscillator platform. Pangolin approved.

Manis Iteritas Alia is a voice based on the architecture of Basimilus. It was designed to be grittier and more aggressive by using only sawtooth waves that are manipulated, modulated, and distorted through a rethought interface. Manis Iteritas Alia is fantastic for leads, basslines, drums, darkness, detuned swarminess, or pure mayhem. Plus, MIA's dedicated envelope output is a great modulation source for the rest of your patch.

MIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal to check out any other Alia firmware, free of charge, any time.

A portion of the proceeds of every Manis Iteritas Alia sold goes to pangolin conservation.

Width: 10HP
Depth: 22mm

Notes: Hybrid additive phase-modulation voice on a swappable oscillator platform

Debel Iteritas Alia is a hybrid additive phase-modulation voice inspired by classic and experimental synth sounds from across the decades. Three synthesis algorithms range from classic FM plucks and basses to all-out additive anarchy. DIA features a two-parameter envelope with a huge range of shapes and timing, making it easy to dial in the exact sound you want. With CV over every parameter, a dedicated envelope output, and an absolutely massive timbral range, Debel Iteritas Alia is a powerhouse synth voice in a compact package.

DIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal to check out any other Alia firmware, free of charge, any time.

Width: 10HP
Depth: 22mm

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Eurorack is a synthesist's toy chest. Stompboxes are a guitarist's toy chest. Each industry offers a seemingly infinite variety of products that enable musicians to build systems unique to their needs and to create a signature sound. Each is also somewhat addictive. Rare is the musician who doesn't eventually need a larger toy chest to house the accumulated toys.

Fortunately for the budget-conscious musician, Eurorack modules and stompboxes have always existed in separate worlds - someone whose Eurorack system consumes an entire wall in their home is usually not the same person whose pedalboard now requires a dedicated roadie just to transport it to the gig.

Intellijel's Stomp removes the barrier between Eurorack and stompbox. It provides the modular synthesist with a portal to stompbox nirvana, and the guitarist with a wormhole to the sonic manipulations of Eurorack modules.

Stomp enables the modular synthesist to interact with the impressive assortment of delays, choruses, flangers, phasers, fuzz boxes, tremolos, wah-wahs, amp simulators, compressors, and pitch shifter pedals available to guitarists. If your effects pedal is adorned with an expression pedal input, Stomp supports that too, and even features a built-in LFO to modulate your pedal's expression input. Need something crazier? No problem. Simply patch any modulation source from your modular system into the expression control jack to override the built-in LFO.

Conversely, guitarists can plug their guitar directly into Stomp's RETURN jack, giving them access to the myriad filters, ring mods, wavefolders and - most importantly - the near-infinite CV modulation delights inherent in Eurorack.

Features:

Robust Neutrik 1/4" TS connectors for the SEND/RETURN and TRS for the Expression interface
Signals arriving at Stomp's RETURN jack pass through a Class A triode emulator, allowing for some tube-like overdrive at high gain setting.
Stomp is more than just a simple level shifter - it's also an impedance converter, which provides proper drive and loading for any FX pedals or instruments you connect.
Separate gain controls on both the SEND and RETURN. This enables you to adjust the level of any audio being sent to the FX pedals as well as any audio coming back into the modular. Not only does this allow you to optimize the signal-to-noise ratio, but by significantly boosting the RETURN level, you can achieve some pleasingly overdriven tones.
Supports both Instrument and Line levels via a front panel switch.
Use Stomp's RETURN circuit as a "direct box" for connecting any instrument.
The high input impedance of the RETURN circuit allows it to be used as a piezo pickup preamp for acoustic instruments.
Use Stomp in the studio as an active "re-amping" device to play pre-recorded tracks back through guitar amplifiers or pedals.
All inputs are protected for minimum RF interference.
Return signal can be phase inverted for use with those pedals or effects types that invert phase.
Low MIX output impedance for driving long cables, lower noise, and minimum interference from outside sources.
The Expression Pedal Output converts analogue CV sources (or the internal LFO) into an output compatible with most stompbox Expression inputs.

Size: 8HP
Depth: 35mm
Power: 47mA @ +12V 13mA @ -12V

Notes: Dizygote is an A-side/B-side digital oscillator with a built-in envelope generator. The A-side builds harmonies with a square waveform and frequency modulation. the b-side distorts a sine waveform with phase modulation.

Inputs:

Trig - button and gate in to trigger oscillator amplitude envelopes
Switch - button and gate in for toggling between the a and b sides
Length - knob and CV in for changing the envelope length
Mod - knob and CV in for changing the phase and fm modulation amounts
Mfreq - knob and CV in for changing the phase and fm modulation frequencies
Freq - knob for setting the oscillator frequency
V/oct - voltage per octave CV for modulating the oscillator frequency

Outputs:

Out L and out R - audio output
Env - CV envelope out