Studio Equipment charts

Notes: Dual xFade is a compact voltage controlled crossfader suitable for both audio and CVs. Smaller knobs set manual crossfade between A<>B, and bigger knobs are CV attenuverters. LEDs show the adjusted positive and negative CV sides for easy monitoring.

Upper inputs (section 1) are normalled to lower inputs (section 2). Thus the same signal pair A&B can be differently crossfaded in both sections.

The switch clones section's 1 controls to the section 2, which is useful to make stereo Dry/Wet adjustment or stereo VCA.

This module can be used as:

two independent crossfades

two independent VCAs

stereo crossfade or Dry/Wet control

stereo VCA

panner

Four jumpers on the back can give optional 5x amplification for each A or B input. Sot it is easy to crossfade modular level with linear level from pedals. Installed jumpers give 1x amplification, removing jumpers gives 5x amplification.

Output 1 is mixed with output 2 if left unconnected.

Notes: Erica Synths Black LPG is our take on Lowpass Gate idea - it's designed from scratch
module featuring 2nd order lowpass VCF (the original Buchla lowpass gate was 1st order
VCF) and VCA combo with distinct resonance circuit on top. Voltage control over VCF cuto
frequency/VCA oset and mode (VCF/VCF+VCA/VCA), as well as built in decay envelope
generator makes it a versatile module for sound shaping in any modular setup.

FEATURES:
Three vactors for 2nd order VCF
VCF/VCF+VCA/VCA modes
Manual and voltage controlled cuto/oset
Manually and voltage controlled mode selection
Manually resonance depth control
Resonance overdrive switch
Built in decay envelope generator
Manually and voltage controlled decay time
Envelope CV output
Ski-friendly design

SPECS:
Audio output amplitude 10Vptp
CV range (full span) -5V - +5V
Max Decay time 4''
Panel width 10HP
Module depth 35mm
Power consumption 44mA@+12V, 45mA@-12V

Notes: Channel extender for MIXCONSOLE.

This module extends the MIXCONSOLE module with three additional channels; the channel level can be controlled via CV here, too. If no CV is attached, the level knob works as usual volume control.

Notes: These knobs are custom made for AE modular; they fit perfectly on the shafts and can be added to all AE modules, no matter of which generation they are.

As of December 2020, all AE modules will be shipped with these knobs as standard.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Notes: Introducing the MAGMA SOLID BLAZE packs, the new benchmark standard in utility backpacks. Designed for modern creators with eco-sustainability in mind.

The new SOLID BLAZE packs are constructed from recycled plastic bottles as the foundation, while maintaining the perfect balance between high-grade material processing, advanced features, and a clean and ergonomic look. When it comes to comfort, performance and functionality, the new SOLID BLAZE packs are unrivalled in the market. Developed to fit a wide range of applications, they make the ultimate travel packs for pro DJs, music producers, photographers, filmmakers, and content creators.

A true packing backpack designed to carry what you need.

The SOLID BLAZE PACK 120 is an all-purpose travel backpack with modular interior layout crafted for versatility. Whether you are hauling DJ or production gear, photo or video equipment, or other electronics, the SOLID BLAZE PACK 120 enables you to easily and conveniently organize your gear. The spacious and expandable main compartment features removable EVA padding and multiple dividers for ultimate packing experience. The customizable padded interior ensures your gear travels with you safely. Loads of additional compartments, pouches and zippered pockets offer intuitive accessory management and quick access to your belongings. The SOLID BLAZE PACK 120 is crafted from only the highest quality materials, such as its water-repellent RPET 900D shell and YKKr AquaGuardr zippers to protect your laptop, tablet, timecode records and other expensive gear from the elements. Travel comfortably knowing your gear is safe inside the MAGMA SOLID BLAZE PACK 120.

FITS:

Pioneer DJM-S11
Pioneer DJM-S9
Pioneer S-1000
Pioneer Toraiz SP-16
Rane Seventy-Two
Rane Seventy
Rane Sixty-Two
Reloop Elite
Akai MPC Live
Akai MPC Live 2
Ableton Push 2
Roland SP404
NI Maschine MK2
NI Maschine+
Denon Prime Go
12" vinyl
Rodecaster Pro
Laptops up to 17"
Camera gear etc.

Outer dimensions: (H/B/T): 52 x 35 x 23-26*cm / 20.5" x 13.75"x 9"-10.25"* (*extended)

Inner dimensions: 45 x 32 x 14 -17* / 17.75" x 12.5" x 5.5"-6.75"* (*extended)

Weight: 2,3 kg / 5lb

Notes: Sound:
Vintage Keyboard Sound Engine with six incredibly detailed vintage keyboard types.

Each keyboard type matches a carefully chosen Drive and Tremolo setting to provide an incredibly musical pairing.

The six keyboard types are:

- RdI, early '70s tine electric piano

- RdII, late '70s tine electric piano

- Wr, late '60s reed electric piano

- Clv, 70s struck string Clavinet

- Toy, toy piano

- CP, Yamaha CP80 electric grand piano

128-note polyphony ensures dropout-free performance.

Five stomp box-style effects with direct control@
The effect types are:

- Drive (adds harmonics and distortion)

- Tremolo (Auto-Pan for Rd) or VCM Wah with adjustable depth and rate

- Chorus with adjustable depth and speed

- VCM Phaser with adjustable depth and speed

- Digital or Analog-Type Delay with adjustable time and depth

- Reverb with adjustable depth

Control:
- Based on the FS action found on the flagship Motif XF, HQ (High Quality) Mini Keys provide premium feel and response for fast, accurate and natural playing

- Sustain pedal input allows the sustain function for all electric piano sounds

Mobility & Connectivity:
- Speakers

2W 3cm stereo speaker system lets you play any place, any time.

Specially designed bass reflex port technology enhances bass response for full, rich sound.

- USB

USB "TO HOST" allows MIDI connectivity to your USB-equipped computer or iOS device.

- Audio output

Dual 1/4"unbalanced line outputs provide connection to mixers, audio interfaces, DI boxes and more.

- Audio input

A 3.5mm aux line input lets you connect and hear mobile devices, tablets and more through the instrument.

Battery Operation:
- Battery powered - uses six "AA" batteries with five hours of life

Create your Soundmondo. Inspire and be inspired:
Soundmondo is a free sound sharing community that lets you discover, create and share reface Voices and Set Lists using Google Chrome any place, any time you're online.

Powered by Web MIDI, Soundmondo is simple to use - just connect reface to Chrome and you're ready to create or start browsing.

Notes: Legendary sound meets the generation of mobile musicians: With the reface Mobile Mini Keyboards, Yamaha introduces a small revolution. Based on legendary synthesizer models like the DX7 or CS series, the company presents four compact instruments, which play to their strengths on the road, on stage or even in the studio. reface is perfect for songwriters, sound designers, live performers and those looking for access to an instrument which allows them to react when inspiration strikes. The online collaboration with musicians around the globe via Yamaha's 'Soundmondo' sound community and the easy connection to notebook, Apple iPhone and iPad are making the four models ideal for being creative together. Battery power and integrated stereo-speakers make the reface quartet ready to play at all times.

From Pink Floyd to Michael Jackson to U2 - with over 40 years in synthesizer history, Yamaha influenced Rock and Pop music like no other instrument manufacturer. Legendary models and series like the CS Control Synthesizer or the DX7 are an inherent part of music history. Time for a small revolution: With the reface Mobile Mini Keyboards, Yamaha presents a range of ultra-mobile synthesizers and a stage-piano that impress with their compact design and web-based sound-exchange. They build the bridge between the sound tradition of the legendary prime fathers and the cooperative music production over the internet.

It started as a sketch of a young Yamaha design team: Under the concept name "reimagined interfaces of classic Yamaha keyboards" the group presented a series of four compact instruments, in which every single one celebrates the personality of a legendary Yamaha instrument - but with a character of its own reimagined for today's 'on-the-go life style'. The concept also integrates a web-based sound exchange between musicians and allows a cooperative sound design. With the introduction of reface, this vision becomes reality.

At home, in a studio, in a park or on a train - the compact design and the powerful integrated stereo speakers allow inspiration in seconds - without any equipment to set up. Creativity can be realised anywhere: Thanks to the battery power, all reface Mobile Mini Keyboards are ready at any time - even when there is no power socket nearby. The setup is done in seconds, even the connection to notebook, iPhone or iPad for the recording and saving of sounds.

All four reface models are presenting themselves as a creative toy for sound design. But despite their compact design, they are professional instruments that are inviting to play. All models feature Yamaha's brand new 'HQ' Mini-Action keyboard with 37 keys (3 octaves). The user interfaces were designed separately for each instrument introducing features such as drawbars for the reface YC organ and the capacitive Multi-Touch surface on the reface DX.

reface YC: Electric Combo Organ - Rich, punchy sounds are its area of expertise: The reface YC offers additive synthesis paired with a unique power of expression using nine drawbars and virtual rotary speakers. The instrument combines five different models of organs, the sound is created using a special "Organ Flutes Tone Generator". In addition to the possibility to carry around five organs in a single piece of hardware without breaking your back, the reface YC delivers the authentic spirit of playing an organ using the smallest user interface possible.

All four reface models offer a rich potential for creative sound design - and the opportunity to get in touch with the whole world: With Soundmondo, Yamaha created an online hub connecting the reface community all over the globe. Soundmondo offers creative possibilities to create, share and discover sounds. The connection is established intuitively using a special Web MIDI technology for Google Chrome. As soon as a reface model is plugged in, it offers the possibility of direct synchronisation. Voices and set lists can be stored in a private area as well as shared with the community.

Quick and easy storage as well as management of sounds with iPhone and iPad: The free reface iOS app for Apple mobile devices makes data transfer extremely simple. A name, a picture and multiple tags can be applied to stored voices; they can be sorted in different ways as well. Search functionality is also included. Using a set list, voices can be arranged in a specific order and recalled one after the other. Another impressive feature is the possibility to exchange voices using QR codes: A distinctive code can be generated from any stored voice and can then be shared using the different options available with iOS. It can for example be sent via email or read using the camera of another iPad to import it into the app.

Notes: The Stereo Mixer 1U provides a convenient way to combine your mono and stereo sources into a single stereo mix. There is level control over the first two channels and, using a rear connector, you can chain multiple Stereo Mixer 1U's together into a hidden 3rd stereo channel without using up channels on the front panel. The chain i/o connectors are fully compatible with the Mixup connectors so you are able to mix 1U and 3U mix chains together as needed.

The Stereo Mixer 1U is a versatile, expandable audio mixer for the Intellijel 1U format. It has two pairs of front panel inputs, each with its own level control, and a mixed output pair. For each input pair, the left channel is normalled to the right channel, for mono operation.

Using 3-pin Link connectors on the back panel, you can chain multiple Stereo Mix 1U's together in series, giving you the ability to mix together even more inputs, or to create sub-mixes for routing audio around larger systems. You can also these same connectors to patch Intellijel's Mixup and XY IO 1U modules to these back-panel chains, and you can connect them directly to the 14" audio jacks on an Intellijel Palette Case, a 7U case with 2nd-generation Audio Jacks Board, an Outs module, or a v2 Headphones 1U.

Stereo Mix 1U is designed specifically for audio (and not for CV mixing), it's AC-coupled, and uses audio-grade, logarithmic attenuators for a smooth, even response across the entire volume range.

Width: 16HP
Depth: 25mm
Power: 17mA @ +12V
23mA @ -12V

Notes: Pico EF is Erica Synths' take on envelope follower module in 3hp! Pico EF features a preamp with +40dB gain (enough to boost even guitar and dynamic microphone signals for use in a modular system), envelope output with adjustable attack time and a gate output with adjustable threshold. The Pico EF can be used as a preamp, overdrive unit or for controlling VCFs with audio signal, or to use with external instruments to control your modular system in other creative and experimental applications.

Technical specifications:

Preamp boost: up to +40dB
Audio output level: 10Vptp
Envelope output level: 0 - +10V
Gate level: +5V
Power consumption: 25mA, -15mA
Module width: 3HP
Module depth: 35mm

Notes: Dust cover for Soma Laboratory Pulsar-23

Notes: Expanded, pro take on IK's excellent compact analogue synth. Dual-filter, three-oscillator paraphonic design with 64-step sequencer, effects and capacitive keyboard (also available with premium keybed).

Supplier's Notes:
Next generation analog for everyone

UNO Synth Pro Desktop gives you the power to create nearly any analog synth sound you can imagine. With its unique dual-filter, 3-oscillator paraphonic design, 256 presets, 64-step sequencer, studio-grade effects, expanded connections and much more, UNO Synth Pro breaks new ground for music makers.

Available in two form factors to suit all players' needs- stage-ready with metal housing and premium keybed; or ultra-portable, USB-powered with capacitive keyboard- UNO Synth Pro offers everyone the next generation of analog sound design in a smart format that fits any space or budget.

3 analog oscillators offer continuously variable waveshape, including pulse-width modulation. Oscillators can be hard-synced for more harmonically-complex tones, and oscillator FM (frequency modulation) lets you shape everything from bell-like sounds to screaming industrial tones. UNO Synth Pro even includes ring modulation for wobbly, sci-fi sound, and a white noise generator for a wide range of percussive sounds and epic rises.

Recreate famous synth sound sources or forge entirely new ones - UNO Synth Pro has the tools you need.

In addition to the original UNO Synth's 2-pole OTA multimode filter, UNO Synth Pro adds a new 2/4-pole SSI LP filter with self-oscillation. The dual filters can be used in series or parallel, with invertible phase, for a total of 24 possible filter combinations.

In short, the UNO Synth Pro Desktop can recreate the filter sound of the most famous classic synths as well as deliver fresh new options to the limits of your imagination.

UNO Synth Pro Desktop offers 2 full ADSR envelopes, one dedicated to the filter and the other to amplitude, with both available as sources to modulate everything from oscillator pitch and waveshape to LFO speed or even other envelope stages.

2 LFOs (low-frequency oscillators) can create classic synth vibrato, wah and tremolo as well as do more complex modulations including audio range FM.

And a 16-slot modulation matrix makes routing all these a breeze. You can quickly and easily design even the most sophisticated modulation scheme, with both internal and external sources, including MIDI controllers.

IK's experience in modeling analog studio effects is decades long. For UNO Synth Pro Desktop, you'll find a super warm and organic true-analog overdrive, plus 12 studio-quality effects in three simultaneous slots: modulation, delay and reverb. External signals can also be routed through these effects, with pre-effects filtering for maximum flexibility.

UNO Synth Pro Desktop provides an enhanced version of the original's long-lasting capacitance-sensing keys along with pitch and mod strips for enhanced expression. And it adds firm-touch rubber pads for the control sections, plus LED-backlit indicators and an LED display for key information, making it easier than ever to use UNO Synth Pro live on stage or in deep programming sessions in the studio.

UNO Synth Pro Desktop offers 256 user-editable presets, each capturing the full state of the sound engine from oscillators to effects.

An onboard 64-step sequencer offers both step and real-time recording, with automation for up to 40 parameters, letting you create incredibly intricate and evolving soundscapes. You can even write CV and gate automation.

And a 10-mode arpeggiator makes it easy to create intricate patterns and runs plus a new "chord mode" that takes advantage of UNO Synth Pro's paraphonic design.

UNO Synth Pro Desktop offers two noiseless, balanced stereo outputs as well as headphone out, for superior audio quality in any situation.

USB and 5-pin DIN MIDI In and Out make it easy to integrate with other synths, Mac/PC and mobile devices, and its assignable CV/Gate connections lets UNO Synth Pro interact effortlessly with your Eurorack or other modular system.

Free Editor

Free UNO Synth Pro Editor for Mac/PC and iPad now available for all purchasers to download. This gives you access to all the advanced features 'under the hood' to manage presets and to easily create your own directly from your computer. Full details on the editor here: https://www.ikmultimedia.com/products/unosynthpro/?p=editor

Software Promo
All purchasers of UNO Synth Pro can now claim 2 free software downloads from IK's SE or CE product range: AmpliTube 5, SampleTank 4, Miroslav Philharmonik, MODO BASS, MODO DRUM, Syntronik 2, and T-RackS 5.

Dimensions:
Size (W x D x H): 25 x 14 x 5 cm, 9.84 x 5.5 x 1.96 in.
Enclosure: Plastic
Weight: 700 g, 1.54 lb
Power: USB Power

Packaging includes:
UNO Synth Pro Desktop
1x Micro USB to USB Cable

Notes: Keyboard version of IK's three-oscillator, dual-filter analogue synth. Classy purist analogue tones with some nice modern features like a step sequencer and effects. Also available in a cheaper, capacitive keyboard version.

Supplier's Notes:
Next generation analog for everyone

UNO Synth Pro gives you the power to create nearly any analog synth sound you can imagine. With its unique dual-filter, 3-oscillator paraphonic design, 256 presets, 64-step sequencer, studio-grade effects, expanded connections and much more, UNO Synth Pro breaks new ground for music makers.

Available in two form factors to suit all players' needs- stage-ready with metal housing and premium keybed; or ultra-portable, USB-powered with capacitive keyboard- UNO Synth Pro offers everyone the next generation of analog sound design in a smart format that fits any space or budget.

3 analog oscillators offer continuously variable waveshape, including pulse-width modulation. Oscillators can be hard-synced for more harmonically-complex tones, and oscillator FM (frequency modulation) lets you shape everything from bell-like sounds to screaming industrial tones. UNO Synth Pro even includes ring modulation for wobbly, sci-fi sound, and a white noise generator for a wide range of percussive sounds and epic rises.

Recreate famous synth sound sources or forge entirely new ones - UNO Synth Pro has the tools you need.

In addition to the original UNO Synth's 2-pole OTA multimode filter, UNO Synth Pro adds a new 2/4-pole SSI LP filter with self-oscillation. The dual filters can be used in series or parallel, with invertible phase, for a total of 24 possible filter combinations.

In short, the UNO Synth Pro can recreate the filter sound of the most famous classic synths as well as deliver fresh new options to the limits of your imagination.

UNO Synth Pro offers 2 full ADSR envelopes, one dedicated to the filter and the other to amplitude, with both available as sources to modulate everything from oscillator pitch and waveshape to LFO speed or even other envelope stages.

2 LFOs (low-frequency oscillators) can create classic synth vibrato, wah and tremolo as well as do more complex modulations including audio range FM.

And a 16-slot modulation matrix makes routing all these a breeze. You can quickly and easily design even the most sophisticated modulation scheme, with both internal and external sources, including MIDI controllers.

IK's experience in modeling analog studio effects is decades long. For UNO Synth Pro, you'll find a super warm and organic true-analog overdrive, plus 12 studio-quality effects in three simultaneous slots: modulation, delay and reverb. External signals can also be routed through these effects, with pre-effects filtering for maximum flexibility.

UNO Synth Pro provides an enhanced version of the original's long-lasting capacitance-sensing keys along with pitch and mod strips for enhanced expression. And it adds firm-touch rubber pads for the control sections, plus LED-backlit indicators and an LED display for key information, making it easier than ever to use UNO Synth Pro live on stage or in deep programming sessions in the studio.

UNO Synth Pro offers 256 user-editable presets, each capturing the full state of the sound engine from oscillators to effects.

An onboard 64-step sequencer offers both step and real-time recording, with automation for up to 40 parameters, letting you create incredibly intricate and evolving soundscapes. You can even write CV and gate automation.

And a 10-mode arpeggiator makes it easy to create intricate patterns and runs plus a new "chord mode" that takes advantage of UNO Synth Pro's paraphonic design.

UNO Synth Pro offers two noiseless, balanced stereo outputs as well as headphone out, for superior audio quality in any situation.

USB and 5-pin DIN MIDI In and Out make it easy to integrate with other synths, Mac/PC and mobile devices, and its assignable CV/Gate connections lets UNO Synth Pro interact effortlessly with your Eurorack or other modular system.

And now, audio input allows access to the filter and FX section for external signals, in addition to the original thru-put for daisy-chaining multiple units together without using a mixer.

Free Editor

Free UNO Synth Pro Editor for Mac/PC and iPad now available for all purchasers to download. This gives you access to all the advanced features 'under the hood' to manage presets and to easily create your own directly from your computer. Full details on the editor here: https://www.ikmultimedia.com/products/unosynthpro/?p=editor

Software Promo
All purchasers of UNO Synth Pro can now claim 2 free software downloads from IK's SE or CE product range: AmpliTube 5, SampleTank

Dimensions:
Size (W x D x H): 55 x 30 x 7 cm, 21.65 x 11.8 x 2.75 in.
Enclosure: Metal/plastic
Weight: 5.8 kg, 12.8 lb
Power: Power PSU

Package includes:
UNO Synth Pro
1x Micro USB to USB Cable
Power Supply Unit

Notes: Huge chorus-flanger. Take your music to infinity. The fully analogue Dreadbox Komorebi Chorus-Flanger Pedal gives you a huge array of sound design possibilities. This powerful pedal can add some serious impact to your sound.

It doesn't matter if you're playing bass, guitar, synths, or even if you want to hook it up to your modular Eurorack system. The Komorebi is ready to go. Sprinkling its beautiful effects over anything it touches.

From a slight pinch of flange to add some movement to your bass lines, or a lengthy chorus effect to treat your pads and chords to a final touch of space-age wideness. It's a guitar pedal but not as you know. Komorebi works with everything.

Current draw: 100mA

Notes: Incredible sounding VCO module that helps you get incredibly rich signals out of your synthesizer. The Dreadbox Hysteria VCO features a huge frequency range of 16hZ to 32kHz. This gives you a lot of functional pitch to work with, allowing you to explore the sounds capable from this module.

The sounds themselves rest on a variable waveform selector - meaning you can scroll through the waveforms and blend them together. This can even be CV controlled, so you can obtain an evolving sound that changes over time. The modules in the Chromatic series give you a great starting point in the world of modular synths and are a must-have for beginners and professionals alike.

Power Consumption: 114mA @ +12V , 46mA @ -12V
10HP
35 mm deep

Notes: The Dystopia is ideal for complex patches where sound can be used to thicken the sound or filter out frequencies. It features a noise generator which can provide white, white to pink, white to blue, scatter, digital, pitch types of noise. The digital noise is brilliant as it can be used as a random gate generator. The bit crusher stage can range from one second up to 8kHz - meaning you can obtain really thick distortions - ideal for a range of styles of music. You can reference all the signals through the four LEDs too - which help you determine the level at which the module is pumping out the noise sources.

Noise Generator (white, white to pink, white to blue, scatter, digital, pitch)
Bit Crusher with range from 1sec up to 8kHz
Digital Noise can also be used as a Random Gate Generator
Dual Filter (parallel) 12dB Low Pass and High Pass Filter
When you insert a signal to the External In, the Internal Noise generator is cancelled and the External Signal is in process
LED indicator for all controls to illustrate the current CV Sum

56 mA +12V
67 mA -12V
35 mm deep
10HP

Notes: Versatile and valuable. The amazing Dreadbox Utopia is a CV audio and manipulator. It allows you to control a wide range of different properties inside your Eurorack system. These include four attenuverters, an offset generator, and a four to three mixer. This selection of tools give you the means to take control of your signals and bend them fully to your liking. Helping you put the finishing touches to your synth patch.

40 mA +12V
27 mA -12V
23 mm deep
10HP

Notes: This is a variant of the standard red / black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Please note: This rack does not include the Master or Power module. To connect the case to power you have the following options:

Connect the case to your system via the Hinge Kit 1 or 2 (only for cases newer than 2019)
Connect the case to your system via the Racklink Module (works for all cases)
Install the Master Module
Install the Power Module

Whichever option you decide on, you will also need to order and install 2x Bus Cables, but be careful to order the correct size! Standard Bus Cable for Standard Case size, etc.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Please note: This rack does not include the Master or Power module. To connect the case to power you have the following options:

Connect the case to your system via the Hinge Kit 1 or 2 (only for cases newer than 2019)
Connect the case to your system via the Racklink Module (works for all cases)
Install the Master Module
Install the Power Module

Whichever option you decide on, you will also need to order and install 2x Bus Cables, but be careful to order the correct size! Standard Bus Cable for Standard Case size, etc.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Please note: This rack does not include the Master or Power module. To connect the case to power you have the following options:

Connect the case to your system via the Hinge Kit 1 or 2 (only for cases newer than 2019)
Connect the case to your system via the Racklink Module (works for all cases)
Install the Master Module
Install the Power Module

Whichever option you decide on, you will also need to order and install 2x Bus Cables, but be careful to order the correct size! Standard Bus Cable for Standard Case size, etc.

Notes: A true all-rounder from Mackie's ONYX range. 12-channel analogue mixer with built-in USB audio interface, allowing you to record your multi-tracks to a DAW or a stereo mix to built-in SD card.

Supplier's Notes:
Incredible sound quality, multitrack recording, and professional built-in effects make Onyx Premium Analog Mixers with USB the ultimate compact, affordable solution for live audio, home recording, and content creation.

If there's one thing Mackie engineers can do in their sleep, it's design a mixer that sounds great, is easy to use, and is packed with flexible features. Sounds pretty good right? So if you mix live sound, record in your home studio, or live stream, this is the heart of your audio.

Onyx Series mixers feature bright, easy to read buttons that shine bright in the darkest places so you will always know whats going on with your mix. On top of that, the full-color display of Studio Command makes it easy to adjust effects and SD card recording/playback.

To create the Perkins EQ, Cal Perkins started with the Wien Bridge circuit topology - a very musical design inspired by the hallowed "British" desks of the 60s and 70s. This design essentially trades boost/cut capability for a wider, highly musical Q filter. After a mind-numbing amount of math, Cal was able to specify capacitor and resistor values that would give the EQ an extra 6dB of control (i15 dB) without excessively narrowing the "Q" or bandwidth of the filters.

Line inputs: 10
Mic inputs: 4
Aux sends: 1
Compressors: 2
USB I/O: 12x4

Notes: Audiophile Circuits League serve up the premium goodies with this hybrid quad VCA/mixer. Four high-quality exponential VCAs with built-in summing and individual outs.

Supplier's Notes:
The ACL VC AMP MIX is a high quality quad exponential VCA with three summed outputs.

The module allows to create a mix of up to four audio sources to three different sums. Available outputs are the sum of channel 1+3, the sum of channel 2+4 and sum of all channels 1+2+3+4. Of course all 4 individual VCA outputs are available as well. It includes an aux input, which will be added unity gain to the sum of all outputs 1+2+3+4 for cascading purposes.

The module can be combined with ACL- RCVS-4 and/or ACL- FCVS-4 CV Source to form a 4 channel voltage controlled mixer very conveniently.

HP : 12

Notes: Strictly limited-edition full-scale reissue of an underrated analogue classic from 1973. The miniKORG 700FS is a classy monophonic instrument with aftertouch and spring reverb.

Supplier's Notes:
Back To The Future: a limited edition authentic revival of the miniKORG 700.

The miniKORG 700 was KORG's first mass-produced monophonic synthesizer released in 1973 at a time when the form of synthesizers as musical instruments had not been fully established. After a lot of experimentation, the miniKORG 700 arrived bringing the world of synthesizers to a wide group of users by offering simple operations that could producing extreme changes in sound, and was championed by a strong base of admiring musicians.

The miniKORG 700FS is an authentic revival of the miniKORG 700S, (an improved version of the miniKORG 700) that was released the following year. The revised miniKORG 700FS offers added functionality such as an arpeggiator, spring reverb and aftertouch. The miniKORG 700FS is a fully-realized analog synthesizer that was developed in conjunction with the original designer, Fumio Mieda.

(Note: To avoid confusion in the following text, both the original miniKORG 700 and the miniKORG 700S are listed as "miniKORG 700" for the most part.)

Why revive the miniKORG 700 now?

The real beauty and awesomeness of the sounds produced by the miniKORG 700 could not be realized through analog modeling technology that uses computational integrated circuitry such as DSPs and other devices to model analog circuitry. And although KORG continues to produce analog synthesizers such as the prologue, the minilogue and many others, we recognize that these instruments owe their existence to the miniKORG 700.

While theoretical know how is important when designing analog circuitry, deep experience is also required to understand what the results will actually be once the circuitry is completed. Ten years have passed since the monotron, a next-generation analog product from 2010 was developed by young KORG engineers and analog enthusiasts. It took some time for the full vision of these engineers to be explored and delivered but at last we've finally arrived - at the start.

KORG's wish is for customers to experience the beauty and awesomeness of the authentic analog sound through the miniKORG 700FS designed by the KORG analog engineers under the supervision of Fumio Mieda, who designed the original circuitry, ensuring that the elements that go beyond the circuit schematics would be faithfully represented.

While the miniKORG 700 was KORG's first synthesizer, it also produced some of the fattest and most dense sounds of all of our synthesizers. The miniKORG 700FS, features oscillators with a penetrating sound and an authentic recreation of the Traveler controller, one of the key features of the miniKORG 700.

The volca keys and volca bass use the filter circuit from the miniKORG 700, because the clear and penetrating characteristics of this filter were a perfect match for products that specialize in lead and bass synth sounds with a strong presence. The miniKORG 700 sound sits easily in today's music, particularly with its lead and bass synth sounds.

The miniKORG 700 came about as a sub keyboard that players would set atop their organs (frequently used in the 1970s) to augment the organ's sound palette. Nowadays, the beautiful lead synth sound of the miniKORG 700FS works well with stage keyboards such as or electric pianos, organs and so on.

The controls on the miniKORG 700 were laid out below its keys in a row, so that players who set the instrument on top of their organ would find them easy to access. Even today, this layout is intuitive and easy to understand, with a unique look that no other instrument offers.

When the miniKORG 700 was originally released, electronic components were larger in size, limiting its functionality due to the small space inside. Thanks to changes in technology, there's now have more space to add a spring reverb effect as well as a joystick for pitch bend and modulation. The new version also features aftertouch for added expressiveness, as well as important features an arpeggiator, USB port, MIDI IN connector and a CV/GATE IN jack.

Dimensions (W x D x H): 744 x 280 x 122 mm/29.29" x 11.02" x 4.80"
Weight: 8.5 kg/18.74 lbs.
Power supply: AC adapter (DC 12V)
Power consumption: 9W

Notes: Serious stereo reverb action in a compact pedal format. Studio-quality Spring, Hall, Plate, BFR, Refract and Air modes with customisable parameters and MIDI control.

Supplier's Notes:
Walrus Audio MAKO R1 is an extremely powerful and versatile multi-function stereo reverb that can quickly go from small intimate room sounds to massive washes of experimental euphoria with six customized, studio-quality programs - Spring, Hall, Plate, BFR, RFRCT (Refract), and Air. Every program can be tuned and tweaked and then saved to one of nine on-board presets.

The R1 boasts a volume swell effect that can be applied to any program, sustain and latching momentary features, stereo in and out, MIDI control, and up to nine on-board presets (128 via MIDI). Players of all styles and genres will be able to find eternal inspiration with the R1.

Programs

Spring - The Spring program emulates an excited spring reverb commonly found in tube amps with loads of transducing drip. Easily go from subtle to full-on surf rock. Experiment with the decay knob to get more than average amounts of reverb not found in traditional amp spring reverb tanks.

X knob adds a warm grit to the reverb decay.

Hall - The Hall program provides the acoustics of large live sound spaces like concert halls to arenas. Longer decays and higher X knob settings result in a massive wash of ambiance. Shorter decay and lower X settings allow for a more intimate reverb expression.

X knob controls the room's size; smaller at lower settings to larger room sizes as you increase X.

Plate - The Plate program emulates a smooth analog plate reverb with nice even diffusion inspired by famous plates like the EMT 140.

X knob adds in gentle warm grit to the front end of the program simulating driving a hot signal into the plate.

BFR - This is more than a giant arena reverb. It's a hall-esque reverb with rich and lush decay in a vast cavern filled with choirs of angels.

X knob controls the amount of diffusion applied to the multi-tap delays used to form the program. At lower X settings, you'll hear these delays bouncing around for a more textured sound. As you increase the X knob, the delays are diffused, creating a smooth texture, and lifting your riffs and chords into the atmosphere. See ya.

RFRCT (Refract) - The RFRCT program allows for lovely, charming, and glitch-like textures hovering over a largely diffused reverb. The Rate controls on RFRCT change how often the glitch effects occur while Depth controls the overall volume of the glitch effect.

X knob is used to shape the tone of the glitch effect. At zero, the glitch effect will have a lo-fi, almost tape-like sound to them. Increasing the X knob brightens these elements with more pristine details.

Air - The Air program offers a larger diffused reverb with a subtle shimmer but has a more "crisp" clarity to its decay. Explore slow-building sounds that don't get in the way of your playing. Air complements keys and synths as well.

X knob controls the amount of the wind and shimmer elements in the Air program. At zero the effect will be off. Turning clockwise will increase the volume of the air effect.

Presets
The R1 can save up to nine on-board presets, and up to 128 are accessible via MIDI. On-board presets are accessible with the bank switch. Cycle between presets in each bank by pressing Bypass and tap at the same time. You will see the right LED change from Red to Green to Blue. Any adjustments made in a preset will change the tap LED to purple, indicating you have edited the preset. The R1 employs a powerful reverb engine that allows for the true preset spill over. When you switch presets, the new preset loads, and the previous preset is allowed to decay naturally.

Tune
Use the Tune knob to shape the amount of low and high frequencies in the reverb signal. The X position is unique to program-specific features listed above.

Tweak
Each program can be fully customized to your taste and playing style with the Tweak knob.
Rate: Controls the rate of the LFO applied to the wet reverb signal.
Depth: Controls the Depth of the LFO applied to the reverb signal.
Pre Delay: Controls how long it takes after you play for the reverb to become audible.

Bypass Modes
The R1 has three different bypass modes.
True Bypass
DSP+True Bypass (trails)
DSP Bypass (trails)

Momentary Functions
Press and hold the SUS/LATCH (Sustain/Latch) switch to momentarily sustain the current reverb and continue to play over it through the same reverb algorithm. No dry signal here! Clicking the SUS/LATCH switch lets you latch the present reverb decay while you play over it.

6 Unique Reverbs
Spring
Hall
Plate
BFR
Refract
Air

Notes: Seriously potent effects power as usual from EarthQuaker. Octave reverb with clever modulation options and eight different modes, from sub-octave generation to pitch-bent harmonies.

Supplier's Notes:
Unrelenting, radicalized reverb for the modern world; an array of haunting, unearthly delights and ethereal sonic sorcery designed to take you on a deep journey through both time and space. This is your new destiny should you choose to accept it. Welcome to your new Astral Destiny.

The Astral Destiny is a compact and powerful modulated octave reverb pedal that features 8 reverb modes with 8 editable presets, assignable expression control, tails for natural reverb decay when the effect is bypassed and a super cool stretch feature that doubles the length of the reverb while adding an adjustable pitch bending effect.

Astral Destiny features a completely analog dry signal path, totally digital delay path, buffered bypass with and two different bypass states- Tails or Full Bypass. Tails Mode, which the is the pedal's stock setting, allows the reverb to naturally decay after the effect is bypassed, slowly letting you drift back from your ethereal dream state into the waking world. Full Bypass, on the other hand, will cut the reverb effect completely when the effect is bypassed and instantly throw you back into cold clutches of reality.

Let your fate spin out of control by pressing the Stretch footswitch doubles the length of the reverb effect while adding a temporary change in pitch. While a short tap will immediately change the pitch, holding the Stretch footswitch depressed gives you a temporary pitch bending effect with the speed of the of the pitch bending effect created by holding the Stretch footswitch easily adjusted by turning the Length knob.

While the Astral Destiny offers two different modes of operation, it ships in Live Mode, where each control will operate manually, laying out your fate for you, clearly visible. Preset Mode in contrast lets you chose from one of the 8 unearthly, ethereal factory preset reverb fates, 1 for each reverb mode, the Astral Destiny comes with. Each of these can be edited or completely overwritten just like when the ancient Fates plucked or cut the strings of ones destiny. Save settings for Length, Depth, Rate, Tone, Mix as well as EXP assignment and Stretch length and recall them instantly. Any of the Astral Destiny's 8 reverb modes can be used as the basis for each of the 8 presets.

But beware! - There is no undo for preset saving, so make sure you are not overwriting your favorite sound, especially when you are saving presets from Live Mode! - Once the string of your fate is cut, there is no turning back on your destiny. Freely express any aspect of your Astral Destiny - Shipping with the EXP jack mapped to the Depth control, the expression control can also be swiftly assigned to Length, Rate, Tone, or Mix, plus different EXP assignments can be saved in each preset and you can also use Control Voltage with the EXP Jack.

Each Astral Destiny is built one at a time by a team of Los Angeles-based robots and a handful of real life humans in the occupied Erie territory presently known as Akron, Ohio.

Notes: Four-input version of Audient's next-generation EVO interface range. Stereo speaker outputs and a pair of headphone outs. Clean sound, clean design: intuitive controls for ease of use.

Supplier's Notes:
Capture your microphones and instruments and start recording audio directly to your computer with EVO 8's intuitive feature set. EVO 8 has all of the innovative new features found on EVO 4 but provides additional inputs and outputs alongside unrivalled performance and functionality - all off bus power.

Made for the smart creative, EVO 8 will deliver a powerful recording solution no matter your artform.

Whether recording your latest track, producing a beat, or creating a podcast EVO 8's advanced and versatile feature set lets you take control of any recording session.

Building on Audient's 20+ years of audio design experience, EVO 8 gives you unrivalled audio quality on your desktop.

Get the most from your microphones with the warm and accurate EVO preamps - offering 58dB of gain range.

Hear your recordings more accurately than ever and make better mix decisions with 113dB of dynamic range.

Plug your guitar or bass straight in through the JFET instrument input and start recording instantly.

Make sure you capture everything perfectly with Smartgain mode. Start playing or singing and Smartgain mode will automatically set the level of your microphones. You can even perfectly match and adjust gain to all channels simultaneously.

Channels 1-4 and both volume buttons can quickly be muted by simply holding them down until they begin to flash.

Individually switch phantom power on/off for each channel and give your microphones the power they need.

*Four channels simultaneously requires a USB-C to C connection. USB-A to C will provide up to two channels.

Set the gain of your mic pres using your DAW, your settings will also be stored in your session.

Control your speakers, headphones and channels all using the volume encoder.

Connecting a set of headphones to either of the headphone ports will automatically mute the corresponding speaker outputs, making switching between loudspeaker monitoring and headphone monitoring quick and seamless.

All of EVO 8's advanced features are powered directly from your computer via USB, letting you start recording on the go, whenever inspiration strikes.

Compatible with all major audio software and plugins, EVO 8 comes bundled with a collection of professional software, giving you everything you need to start recording.

Audio Loop-back
Audio Loop-back enables you to record your computer audio at the same time as your microphones. Ideal for podcasters and streamers.
Record your computers audio
Record guest Skype/video calls
Record gaming audio

Designed to simplify and adapt to your workflow, the EVO Mixer enables you to effortlessly set up and route your inputs + outputs, provide ultra-low latency monitoring, balance and set your levels, activate phantom power, set up dedicated artist headphone mixes and more.

Minimalist layout. Innovative Engineering. Modern aesthetics. EVO 8 has been designed to last and look at home on your desktop.

Notes: One of the most impressive granular synthesis approaches in Eurorack, combining looping and granular effects with buffer sizes up to five minutes. Hugely creative and powerful dual-module setup.

Supplier's Notes:
There's a long history behind the granular concept and many reinterpretations of it's core principles, this is ADDAC's take on it.

In a loose description digital Granular refer to pieces of sound files being played at the same time with slight or completely different parameters originating what is commonly referred to as granular clouds. Normally there's a buffer size from which the granular engine snips it's pieces from and plays them according to the parameters set. This buffer size is normally small in size where grains are so small that can reach the hearing spectrum and be heard as a sort of ever changing complex wavetable, this is the principle behind granular synthesis.

ADDAC have added the possibility of long buffer sizes up to 5 minutes, allowing "softer" approaches to the granular principle using it as an effect that can generate from "accidental" effects like slight "stutters" to extreme processing and transformation of any incoming audio signal.

This module is conceptually deep but easy to grasp and operate as all controls are in its dedicated panel, all jack inputs and outputs have its own separate panel to allow no compromise when playing it's controls.

There are three main sections in this module:
Looper Engine: The Looper is where all the Real-Time recording happens. The audio input feeds the recording buffer, multiple controls allow to record and play loops into a list so that any sample in the list can be accessed at ay time and more acting as a standard looper
Granular Engine: The Granular acts upon the buffer of whatever LOOP is selected.
Output Mix The output mix allow individual control for the Dry Input, Looper Volume and Grains Volume.
Besides these main sections there's also a simple strip down MENU mainly used to LOAD and SAVE Banks, no Menu diving guaranteed.

For more detailed info, please refer to the User's Guide.

Audio Specs:
Audio input: Stereo, 16bit 44.1Khz
Audio output: Stereo, 16bit 44.1Khz

Tech Specs:
32HP + 13HP
4.5cm deep
240mA +12V
70mA -12V

Notes: Cost-effective all-in-one bundle from Moog: two semi-modular instruments, mixer, cables, accessories and educational materials. Just add speakers or headphones and you're all set.

Supplier notes:
Moog Sound Studio: A complete analog synthesis studio in a box. Everything necessary to start patching today. All you need is a pair of headphones!

Ready to take the next step in your analog synthesis journey? The Moog Sound Studio has you covered. Moog Sound Studio is an all-inclusive bundle of semi-modular synthesizers and accessories created to provide users with all of the equipment, cables, accessories, and educational tools needed to enter the world of analog synthesis for the first time or to continue to explore sound in an immersive new way. All you need is your own headphones or personal speaker and you're ready to get started!

Moog's Mother-32 and DFAM synthesizers are a perfect pairing to anchor any electronic studio. Mother-32 is a versatile performance and production synthesizer with a powerful step sequencer and 64 slots of sequence memory. Its classic Moog synth voice delivers raw analog sound, deep Moog bass, and soaring synth leads, forming an excellent compliment to DFAM's rich analog rhythms and percussive patterns. Equally impressive on their own, these synths become truly magical when combined into a single system. By patching Mother-32 and DFAM together, a symbiotic sonic relationship is formed that unlocks new capabilities and empowers new ideas.

Along with a duo of semi-modular analog synthesizers, each Moog Sound Studio includes a personal stereo summing mixer with 3-way power distribution to provide flexible signal routing and power your entire system conveniently from a single power supply. Also included are a series of guided exercises, exploration games, experimental patch sheets, imaginative studio art, and more to outfit your studio and take your synthesis skills to the next level. And of course, all of the cables and accessories needed to connect everything are included as well!

Moog Sound Studio takes the magical environment and hands-on learning experience of Moog installations found at events around the world and presents them in a way that empowers you to explore synthesis with joy and confidence from the comfort of your own home or studio.

This is an exciting time to be a part of the growing synth community. The Moog Sound Studio is here to provide a meaningful electronic experience that informs, inspires, and nurtures synthesists at any point in the creative journey.

Mother-32
Mother-32 is an intuitive and expandable semi-modular synthesizer that adds raw analog sound, powerful sequencing, and extensive interconnectivity to any creative, electronic, or modular ecosystem. Mother-32 Excels at: Classic analog bass & leads and powerful step-sequencing with pattern memory.


DFAM
DFAM (Drummer From Another Mother) is a semi-modular analog percussion synthesizer that empowers an expressive hands-on approach to percussive pattern creation. DFAM Excels at: Rich electronic drum patches and organic analog sequencing that breathes.

Personal Stereo Summing Mixer and Instrument Cables
This 4-input analog summing mixer (1/4" IN, 1/8" stereo OUT) features selectable mono or stereo configurations for versatile routing options, and the built-in 3-way power distribution hub supplies power throughout your Moog Sound Studio conveniently from a single power supply. The included instrument cables come in lengths and colors to compliment the system and reduce clutter.

2-Tier Rack Kit
Conveniently stack both synthesizers and the summing mixer together as one connected system to maximize studio space and orient instruments vertically for optimal interconnectivity.

Cable Organizer and Custom Patch Cable Set
The included patch cable organizer connects to the two-tier rack or mounts directly to any wall, keeping patch cables neat and orderly for a hassle-free workflow. A custom set of patch cables has been selected in lengths, colors, and quantities to maximize system patchability.

Guided Exercises, Exploration Games, and Experimental Patch Sheets
Learning synthesis doesn't have to be intimidating! Included games and educational materials allow the player to explore at their own pace while enjoying the journey. Developed with artists who know these instruments best, these detailed and fun exercises are designed to accelerate your synthesis experience by exploring new skills to support your ongoing synthesis practice - A perfect jumping-off-point for beginners or source of inspiration for the seasoned pro.

Studio Art
All original artwork, created by Jim Stoten (M32/DFAM) and Philip Lindeman (SUBH/DFAM), has been thoughtfully designed to aid users in the exploration of new imaginative worlds. The characters, poster, and objects that accompany each Moog Sound Studio come together to transform any space into an immersive creative environment.

Notes: A standalone alternative to the clip-and-scene production workflow of software like Ableton Live. Huge production and performance potential with built-in synths, effects and sampling power.

FORCE 3.2 is the MOST POWERFUL STANDALONE music production system for studio production and live performance. Now, FORCE 3.2 delivers even more inspiring plugin FX, sounds, creative editing, arranging and vocal effects processing as well as award-winning mixing and mastering plugins from world-renowned AIR Music Tech.

MPC Plugin Instruments
New Sounds Mode
New AIR Effects
Probability & Ratcheting
Automation Snapshots | Track Reorder
FORCE Tuner

Supplier's Notes:
Introducing Force, the ultimate in standalone end-to-end production workflows, complete with every tool you need to produce, remix, mashup and perform your tracks live. Fusing clip-launching, a linear arranger, MIDI Multi capability, step sequencing, sampling, synth engines, tactile touch screen control and much more, all in a singular standalone device, Force is primed for any setting, from the studio to the mainstage - no computer needed.

Launch Clips, browse your sounds, edit MIDI data, manipulate samples, arrange your composition, apply XYFX, sculpt synth sounds and much more, all from Force's 7-inch, full-color, capacitive multi-touch display.

Find your creative flow with Force's arsenal of tactile controls. Trigger scenes/clips, step sequence, finger drum and play note data with an expandable 8x8 clip launch matrix. Discover new ways to supercharge your performance via 360-degree rotary encoders with OLED feedback for immediate real-time access to all core controls or any assignable parameter. Fast-track your workflow with Force's collection of smart controls for navigation, playback/recording control, note expression, crossfading and much more.

Load your samples from a USB thumb drive or SD card, or expand Force's storage with the SATA drive bay. Capture audio with (2) XLR/14-inch combo inputs with phantom power, switchable to line/instrument level. Route your audio to two stereo 1/4-inch outputs, selectable per track within Force's UI. Use the headphone out as a cue bus to audition clips/scenes. Take control of your modular gear with four independent CV/Gate outputs and unite your peripheral MIDI equipment courtesy of MIDI In/Out/Through ports and USB via Force's unprecedented MIDI Multi capability. Connectivity and storage restrictions are things of the past!

From sparking that initial idea to arranging and final mixdown, everything your production demands is here. Record, program and sequence with multiple track types including Plugin Tracks with MPC-style Drum Tracks, Audio Tracks, Keygroup Tracks, MIDI tracks and CV tracks. Sketch out song sections in performance mode, then arrange these on Force's linear arranger. Add the final polish to your track using dozens of processors and effects from the AIR FX suite, all controllable via smart assignments on the rotary encoders or the displays on the touch user interface.

For the DJ, Force immediately connects to your live rig either as a feature-rich side-cart or a solo centerpiece. Remix and mashup tracks on Force's 8x8 clip matrix. Import multiple stems, then time-stretch and pitch-shift your content all in real-time. Assign tracks to Force's crossfader and load full tracks, stems or loops to Force's 8x8 matrix. Add an extra dimension to your performance with tactile XYFX. Connect Force to your wireless network and sync your project with any Ableton Link compatible application or hardware device. The creative possibilities are only as limited as your imagination - adding an extra dimension to your DJ performance has never been simpler.

KEY SPECS:

Pads:
(64) velocity- and pressure-sensitive pads, RGB-backlit

Knobs:
(8) 360- touch-sensitive Knobs
(1) 360- encoder for display navigation and selection via push
(5) 270- knobs for gain, mix & level adjustment

Buttons:
(56) dedicated function buttons; red-, amber-, or green-backlit

Display:
6.9" / 176 mm (diagonal)
5.9" x 3.7" / 150 x 93 mm (width x height)
Full-color LED-backlit display with touch interface

Connections:
(2) XLR+1/4" (6.35 mm) TRS inputs (Input 1/2)
(4) 1/4" (6.35 mm) TRS outputs (2 stereo pairs)
(1) 1/4" (6.35 mm) stereo headphone output
(1) 1/8" (3.5 mm) MIDI input
(1) 1/8" (3.5 mm) MIDI output
(1) 1/8" (3.5 mm) MIDI thru port
(4) 1/8" (3.5 mm) CV/Gate outputs
(1) Ethernet link port
(2) USB Type-A ports
(1) USB Type-B port
(1) SD card slot
(1) power adapter input

Power:
Via power adapter: 19 V, 3.42 A, center-positive, included

Dimensions (width x depth x height):
13.8" x 15.3" x 2.85"
350 x 389 x 72.5 mm

Weight: 8.53 lbs./3.87 kg

Notes: Great value for FL Studio users with this dedicated controller which channels Akai's expertise in order to offer a hands-on experience for your DAW. Quicker workflow and easier access to settings.

Supplier's Notes:
The new Akai Professional Fire represents the first of its kind, a dedicated hardware controller for the FL Studio Digital Audio Workstation (DAW) platform. Created in close partnership with Image-Line, Fire is a high-performance tool designed to enhance the workflow and music-creating experience for all FL Studio producers.

Fire features a dedicated browser function to navigate, audition and load your audio samples, recall project files and open plugins. Simply select browser and use the Select rotary encoder to preview and load content and devices within FL Studio - The graphical OLED display makes for easy browsing and controlling the various files, menus and parameters within your session a breeze.

Featuring plug-and-play integration, within seconds you'll be creating patterns and building tracks using Fire's 4 x 16 velocity-sensitive RGB pad matrix, designed for immediate interaction with FL Studio's celebrated step sequencer.

Get hands-on with your production with everything you need to control FL Studio's channels and patterns. With direct hardware control over your session, you can easily mute and solo channels, expand the grid matrix, select new channels, navigate through patterns and much more without touching a mouse.

From searing synth leads to lush pads, Fire's Note mode provides the ultimate platform to add melody and harmony to your production. Simply push the Note button and Fire's RGB pads switch-up to a MIDI keyboard giving you three octaves of note data, perfect for playing all of your instruments hosted in FL Studio.

Fire's pad matrix features an MPC-style 16-pad layout for seamless integration with FPC and SliceX. This is great for FL Studio producers who want a traditional beat-making experience or want to use their finger-drumming chops on the track.

Whether you're a studio producer refining an arrangement or live performer looking to take your sessions to the stage, Fire's Performance mode provides the ideal platform to remix and reimagine your tracks. Simply select Performance mode and launch MIDI clips and audio directly from Fire's RGB pad matrix for a truly inspiring live production experience.

Fire also provides immediate access to transport controls straight from the hardware. Record, Stop, Play, as well as a button to instantly switch between Pattern and Song mode are intuitively placed for mouse-free control of FL Studio. Plus, these all double up with secondary controls providing access to Loop Record, Countdown, Wait and Metronome.

Bringing a tactile, mouse-free mixing solution to the FL Studio environment, Fire includes 4 banks of 4 touch-capacitive knobs that enable the user to instantly see and adjust parameter values. Providing control over channel, mixer and user-assignable parameters, this enables a more intuitive and enjoyable workflow. From tweaking volume and pan within FL Studio's mixer to adjusting filter controls within the selected channel and recording automation, you'll spend less time clicking and more time executing.

Speed is power. Up to four Fire devices can be connected at once, enabling unprecedented hardware control over the FL Studio mixing and production workflow. Expand channels or make more in the sequencer accessible by selecting Multi-Device Mode from the OLED display. Instantly expand the 4 x16 matrix of one Fire unit to an 8 x 32 workflow.

Enter the ground-breaking, high-powered workflow heard all over the charts with the FL Studio Fruity Fire Edition software, included with Fire. FL Studio is a complete software music production environment, the culmination of more than 20 years of innovative development. The software features everything you need in one package to compose, arrange, edit, mix and master professional quality music. With access to FL Studio's piano roll editor, step sequencer, playlist, VST instrument support, full automation functionality, plus 18+ virtual instruments and over a dozen built-in effects and processors, FL Studio Fruity Fire Edition provides the ultimate platform to spark that initial idea, ignite your creativity and complete your masterpiece - all in an ultra-intuitive, inspiring environment engineered to keep you tuned in to what's important, your music.

Pads: (64) Velocity-Sensitive RGB Backlit Pads

Knobs:
4 x 360 degree Assignable Touch-Capacitive Knobs
1 x 360 Encoder for Display Navigation

Buttons: 20 x Dedicated function buttons; Red, Amber or Green backlit
Display: OLED Display
Connections: 1 USB Type-B Port

SYSTEM REQUIREMENTS
Windows 7, 8, 10 or later
4GB of RAM or higher recommended
4GB free disk space
FL Studio 20.0.5 or later

Mac OS:
10.11 or later
4GB of RAM or higher recommended
4GB free disk space
FL Studio 20.0.5 or later

Notes: Unusual output and mastering module, inspired by studio and radio mastering tools but fitting into just 6hp. Includes multi-band compression, mid/side stereo processing and brickwall limiting.

Supplier's Notes:
Golden Master is a multiband processor module in Eurorack format. Inspired from the studio mastering and radio loudness units from the 90's, this tool is a game changer for everyone who performs live with a Eurorack synthesizer.

The whole magic of Eurorack lies in its raw sound and simple analog mixes - processing through the Golden Master brings instant punch and sound pressure, as well as controlling the overall volume.

Power consumption: 135mA at +12V and 25mA at -12V
Depth: 30 mm (with ribbon cable connected)
HP : 6

Notes: The ultra-portable MPK Mini Play is based on the world's most popular midi controller - Akai Professional's MPK Mini-but now it comes packed with 128 sounds and its own built-in speaker. With 8 backlit MPC drum pads and a 4-way joystick for simple control, players have all they need to play their music anytime, anywhere. Four knobs (two banks capable of controlling eight different parameters) can be used to tweak sounds and edit multiple parameters in real-time, giving musicians even more performance possibilities. Powered by 3 "AA" batteries, the MPK Mini Play is built for hours of wireless fun.

Not just a mini keyboard, the MPK Mini Play can also connect to a computer via USB port for the same plug-and-play MIDI functionality as the classic MPK Mini controllers. If not disturbing others is a priority, players can use the mini-audio output jack to connect headphones to the MPK Mini Play. When you want a bigger sound, simply connect to external speakers using the same output jack. All-in-one, easy-to-use fun with "pro" features - that's the MPK Mini Play!

"We are extremely excited to introduce the MPK Mini Play," said Dan Gill, Product Manager for Akai Professional. "The MPK Mini was a huge hit with musicians and now having all those sounds on-board with a built-in speaker, along with its go-anywhere portability, Play opens up new musical possibilities that people are going to love."

KEY SPECS

Keys
25 velocity-sensitive

Pads
8 pressure and velocity sensitive
MPC-style Light-up Pads x 2 Banks

Knobs
4 assignable controller pots
1 x 360 Encoder for Display Navigation
1 Volume control

Computer Interface
USB-MIDI communications to Mac/PC

Octaves
10 with Octave Up and Down

Arpeggiator
Yes

Additional Controls
Pitchbend/Mod Joystick
Note Repeat Button
Full Level Button
Tap Tempo Button

Additional Inputs
1 14" (6.35mm) TS input for sustain pedal

Output
1 1/8" (3.5mm) headphone output
Built-in speaker

Power
USB bus powered
3 x AA batteries

Dimensions:
12.29" x 6.80" x 1.83" / 31.2 x 17.2 x 4.6 cm (WxDxH)
1.6 lbs

Notes: A unique approach to FM synthesis in this updated version of Kodamo's ludicrously powerful EssenceFM. Up to 300 voice polyphony, hugely powerful touchscreen editing and stereo effects.

Supplier notes:
The EssenceFM is a powerful and easy to use FM synthesiser, allowing you to explore the endless soundscapes offered by FM synthesis. With a super-responsive touchscreen, assignable knobs and workflow optimized for sound design, creating rich and unique sounds is easier than on any other FM synthesiser.

The EssenceFM engine allows to create ridiculously powerful sounds made of more than 6 operators. That's why it's been given 300 voices of polyphony, you get the easy-to-program 6 op FM synthesis and the ability to layer many voices to create huge, rich-souding instruments.

There are 1800 operators and 4200 envelopes running at the same time, more than you will ever need.

This synth is the result of Kodamo's efforts to create the best user interface to interact with FM synthesis. No endless menus, no weird key combinations, no complex structure to remember. Everything is displayed on screen, every element is editable by pressing on it.It requires some trial and error to find the perfect sound, and that exploration process is fun only when the interface doesn't work against you. The EssenceFM is full of small details that makes workflow better: 1024 undo/redo steps while editing, copy/paste on every element, clear navigation using 4 modes and a breadcrumb, real-time envelope level display on the operators and much more. All that makes for a powerful and enjoyable synthesiser.

What you can do with it:
Create your own FM algorithms by drag and dropping operators on the touch screen. An almost infinite number of configurations is possible
Layer up to 128 voices per patch, each consisting of 6 operators, for incredibly rich sounds
Draw your custom waveforms on the touch screen to use them as oscillators or LFOs
Thicken the sound with the built-in effects
Take advantage of its 16 part/300 voice multi-timbrality to create full songs with it
Use it to make analog-like sounds with the built-in resonant filter
Connect it to your audio recording gear and effect modules in many different ways with the four balanced stereo outputs
Explore FM synthesis in the most convenient way possible with the Undo-Redo buttons, allowing for any action to be undone
Try microtunings, layer splits, round robin, MPE, and many other advanced features.

Package Contents:

EssenceFM synthesizer (MKII version)
Printed user manual
2x 3U 19" rack mount brackets
4x screws
Universal (100-240V) AC adapter
IEC power cable
2x rubber strip

Notes: The new Akai Professional Fire represents the first of its kind, a dedicated hardware controller for the FL Studio Digital Audio Workstation (DAW) platform. Created in close partnership with Image-Line, Fire is a high-performance tool designed to enhance the workflow and music-creating experience for all FL Studio producers.

Fire features a dedicated browser function to navigate, audition and load your audio samples, recall project files and open plugins. Simply select browser and use the Select rotary encoder to preview and load content and devices within FL Studio - The graphical OLED display makes for easy browsing and controlling the various files, menus and parameters within your session a breeze.

Featuring plug-and-play integration, within seconds you'll be creating patterns and building tracks using Fire's 4 x 16 velocity-sensitive RGB pad matrix, designed for immediate interaction with FL Studio's celebrated step sequencer. Get hands-on with your production with everything you need to control FL Studio's channels and patterns. With direct hardware control over your session, you can easily mute and solo channels, expand the grid matrix, select new channels, navigate through patterns and much more without touching a mouse.

Get hands-on with your production with everything you need to control FL Studio's channels and patterns. With direct hardware control over your session, you can easily mute and solo channels, expand the grid matrix, select new channels, navigate through patterns and much more without touching a mouse.

From searing synth leads to lush pads, Fire's Note mode provides the ultimate platform to add melody and harmony to your production. Simply push the Note button and Fire's RGB pads switch-up to a MIDI keyboard giving you three octaves of note data, perfect for playing all of your instruments hosted in FL Studio.

Fire's pad matrix features an MPC-style 16-pad layout for seamless integration with FPC and SliceX. This is great for FL Studio producers who want a traditional beat-making experience or want to use their finger-drumming chops on the track.

Whether you're a studio producer refining an arrangement or live performer looking to take your sessions to the stage, Fire's Performance mode provides the ideal platform to remix and reimagine your tracks. Simply select Performance mode and launch MIDI clips and audio directly from Fire's RGB pad matrix for a truly inspiring live production experience.

Fire also provides immediate access to transport controls straight from the hardware. Record, Stop, Play, as well as a button to instantly switch between Pattern and Song mode are intuitively placed for mouse-free control of FL Studio. Plus, these all double up with secondary controls providing access to Loop Record, Countdown, Wait and Metronome.

Bringing a tactile, mouse-free mixing solution to the FL Studio environment, Fire includes 4 banks of 4 touch-capacitive knobs that enable the user to instantly see and adjust parameter values. Providing control over channel, mixer and user-assignable parameters, this enables a more intuitive and enjoyable workflow. From tweaking volume and pan within FL Studio's mixer to adjusting filter controls within the selected channel and recording automation, you'll spend less time clicking and more time executing.

Speed is power. Up to four Fire devices can be connected at once, enabling unprecedented hardware control over the FL Studio mixing and production workflow. Expand channels or make more in the sequencer accessible by selecting Multi-Device Mode from the OLED display. Instantly expand the 4 x16 matrix of one Fire unit to an 8 x 32 workflow.

Pads: (64) Velocity-Sensitive RGB Backlit Pads

Knobs:
4 x 360 degree Assignable Touch-Capacitive Knobs
1 x 360 Encoder for Display Navigation

Buttons: 20 x Dedicated function buttons; Red, Amber or Green backlit
Display: OLED Display
Connections: 1 USB Type-B Port

SYSTEM REQUIREMENTS
Windows:
Windows 7, 8, 10 or later
4GB of RAM or higher recommended
4GB free disk space
FL Studio 20.0.5 or later

Mac OS:
10.11 or later
4GB of RAM or higher recommended
4GB free disk space
FL Studio 20.0.5 or later

Notes: Premium analogue delay from Erica's flagship Black Series range. Two bucket brigade device delay lines work simultaneously with smooth crossfading and tons of voltage control. Lovely.

Supplier's Notes:
Erica Black Series include high-end, unique functionality and superior quality modules. Only the best, highest quality components are used, all inputs and outputs are protected against undesired overvoltage. When designing Black Series, put design and usability superior. Big knobs are assigned to functions that make difference in sound. Erica Black series consist of range of modules that are needed to put together entire synth. Enjoy!

The Erica Synths Black BBD is one of kind analogue delay module. It features two BBD lines: short, 1024 stage and long, 4096 stage, that work simultaneously and you can smoothly fade between those two, thus creating distinct multitap effect.

Furthermore, an advanced BBD clock noise cancellation circuit is implemented that reduces unwanted BBD noise without filtering higher frequencies of audio signal. Most of parameters are voltage controlled, which allows to integrate the module in complex modular setups.

Time

This is delay time manual control.

Because of BBD clock suspension circuit, delay time can be pushed in extremely long regions, however in that case BBD clock noise may appear. The Time CV is added to the knob setting.

In level

This is the input attenuator switch. Select among full amplitude, half amplitude and audio off.

BBD mode

This control smoothly fades between short and long delays. Any setting in-between will result in distinct multitap delay effect.

LFO rate

Adjust the internal modulation LFO rate. The internal LFO controls delay time, and it's automatically disengaged, when an external modulation signal is connected. The LED gives visual feedback on the LFO rate.

LFO shape

Select the LFO shape. Three shapes are available - triangle, square and in-between shape - mix of triangle and square.

Input

This is the audio input of the module. This is manual Dry/Wet mix. The MIX CV is added to the knob setting.

Colour

Even though the module has BBD clock suspension circuit, the colour switch provides extra lowpass filtering of the signal. At top setting no filtering is applied, at lower settings increasing filtering is present.

Feedback

This is the delay feedback manual control. In extreme clockwise settings the module goes into self-oscillation, and by adjusting delay time and BBD mode settings, the module becomes a drone machine. The FBK CV is added to the knob setting.

CV level

This is the Time CV level attenuator. If nothing is patched into TIME CV socket, it controls the internal LFO amplitude.

WET out

This is the WET signal output of the module - use it for advanced patches.

Out

This is the main output of the module.

Time CV; FBK CV; Mix CV;
These are CV inputs for Time, Feedback and Dry/Wet mix.

SPECS:
Audio level 10Vptp
CV level (full span) -5V - +5V
Power consumption +95mA, -81mA
Module width 12HP
Module depth 35mm

Notes: A solid gold modern classic from FMR. The RNC must be one of the biggest studio bargains around. Proper analogue compression with digital control, offering pro sound at an affordable price.

Supplier's Notes:
What It Is

FMR Audio's first product, introduced over 18 years ago, the Really Nice Compressor (RNC) is a compact and cost-effective stereo compressor with a high-fidelity audio path and compression scheme. The RNC provides quality compression at a budget price.

How It Sounds

The RNC provides two modes of operation. One allows the RNC to be used for special effects, like snappy snares or popping basses. The other provides near-invisible signal compression for sensitive material where compression artifacts are less desirable (like natural vocals, acoustic guitar or the program bus). The RNC yields clean, airy compression with few artifacts and little high-end loss, even at massive gain reduction! The amazing performance is why- even after almost 20 years- many professionals are calling the RNC one of the best sounding compressors for under $2000.

How It's Done

The RNC achieves such high performance at a low cost by using using a microprocessor to replace discrete sidechain components (resistors, diodes, capacitors, opamps, transistors, etc) with chunks of software, thereby reducing the component cost. This approach, however, still processes the main audio in the analog domain, avoiding the problems associated with digital audio conversion (e.g., latency, digital artifacts). Even the problem of "scratchy" pots and switches are avoided: no audio flows through the front-panel controls. The front-panel pots and swtiches merely feed DC voltages to the microprocessor and it takes care of adjusting parameters and signal path with components - like sealed-relays and VCAs - located close to the input/output jacks avoiding noise pickup and audio quality reduction due to aging controls! With this blend of technology, the RNC offers the accuracy and precision of digital control with the clean tonal character of an all-analog signal path. The RNC's digital control permits accurate repeatability of your favorite settings.

Notes: What It Is

Years ago, many RNC users pined for less invisible compression and requested that FMR Audio offer a more "colourful" compressor, suitable for bass guitar, drums and other sources in need of added sonic texture. In response, the FMR designer went to the RNC archives and resurrected a version of RNC software that had been rejected for release because it wasn't invisible enough! The result: a compressor reminiscent of some classic opto compressors used to just "level" the signal rather than tame every transient. To celebrate the RNLA's sonic "colour", a bright red knob* was chosen as a visual metaphor. Although the most recent version ships with a less ostentatious red-striped knob (not shown), the RNLA's sonic colour remains bolder than ever...

How It Sounds

"Thick" and "gooey" is how some customers have described the RNLA's sound. The RNLA is, admittedly, much "gentler" and not as apt to grab'n'run with the signal. Like an old-timey photocell, the RNLA is a little resistant to responding right away, but requires the signal to be there for a while to get the photocell to act. This action yields a soft musicality to the compressor's action that adds a desirable characteristic to the source signal.

How It's Done

The RNLA and the RNC share much of the same hardware, but run different algorithms to achieve the desired effect. The RNLA exercises the well-known dictum (among dynamic processor designers) that, after the static characteristics of the signal path, the main contributors to a processor's sound are the shapes of the attack & release envelopes. The RNLA's software then transforms the sidechain signal into a drive signal for the VCA that both slows things down a bit and totally reshapes the crisp and quick action of the RNC's "normal" mode. This reshaping (and slow down) are the primary sonic drivers behind the RNLA's "thick and gooey" sound!

Notes: The low-cost, high-quality Hosa MIDI cable is designed to interconnect MIDI devices. Unlike other cables, the Hosa MIDI cable is wired 5-pin discrete and compatible with all MIDI standards, including SysEx. These durable MIDI cables come in several lengths, from 1 foot to 25 feet, so you can get the right length for your needs.

Features include:

Nickel-plated plugs for rugged durability and efficient signal transfer
Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
OFC spiral shield for effective EMI and RFI rejection and flexibility

Connectors: 5-pin DIN to Same
Color: Black

Notes: The Beautifier is a flexible OTA based filter, featuring a lowpass/bandpass switch and a selectable slope of 24db and 12dB. Two attenuated CV inputs for frequency cut-off and resonance. The filter self-oscillates at a given point and can be driven quite hard if you crank up the gain. All in all, a versatile analogue workhorse with a lot of character; from smooth and creamy to quite raw and screamy.

47 mA +12V
19 mA -12V
0 mA 5V
26 mm deep

Notes: mioXM - more connectivity than you can shake a stick at.

With mioXM it's never been easier to get all of your MIDI gear talking to each other. Harness the power of iConnectivity advanced computer and network connectivity and experience why mioXM redefines what a MIDI interface can and should do.

Connect all your MIDI devices (USB-MIDI, DIN-MIDI, RTP/Network-MIDI) and let this rugged, versatile interface put you in control of your MIDI devices and workflow.

On stage or in the studio, RTP/Network-MIDI capability means you are no longer constrained by cable length or limited USB ports. Stack multiple interfaces and computers on a network for ultimate scalability and flexibility.

With mioXM, you're able to streamline and expand your MIDI setup, and do it faster, better, and in creative and exciting new ways.

What makes mioXM unique? The iConnectivity difference.

Powerful network MIDI capabilities:

Network connectivity means MIDI wherever you need it. Regular USB connectivity limits you to keeping your interface within 15ft of your computer. Network / Ethernet connectivity gives you up to 330ft / 100m connection between you and your interface.

Drop an interface in every room of your studio, or place an interface virtually anywhere in a venue.

RTP/Network-MIDI is not bound by some of the same restrictions as USB-MIDI.

Easy renaming of network ports - have them show up the way you want them to in your DAW.

Access to more than12 ports per interface.

iConnectivity's unique network technology is as easy to use as USB! Enjoy your new-found MIDI power without extra headaches.

Use your 12 network MIDI ports anyway you want. Connect each of the 12 RTP-MIDI sessions to any combination of physical or virtual I/O ports. Almost any combination is possible.

Configuring mioXM:

Introducing a new version of iConnectivity's Auracle control software: taking the simplicity of workflow that the original Auracle introduced but now with the added deep configuration functionality that iConnectivity become known for. All the deep configuration options you asked for: MIDI merging, filtering, remapping, and deep routing are all there and super easy to use.

Presets onboard:

Need to configure your MIDI setup in multiple ways? No problem!

Store and recall up to 4 presets directly on the interface, without even needing a computer!

Easily recall unique MIDI routing, filter and merging setups to preset scenes, all from the front of mioXM.

What's in the box
1 x mioXM
1 x USB cable
1x Ethernet cable
1 x mioXM 12V 36W Power Power Supply with interchangeable blades (NA, EU, UK and AU (Australia only)).

Device Specifications:

Width: 214 mm/8.43 in
Height (1U): 37 mm/1.46 in
Depth: 140 mm/5.51 in
Weight: 992g/2.13 lbs

mioXM fits comfortably in iConnectivity's iCRS Interface Rack Shelf

System Requirements

Macintosh
Mac OS X 10.11 or greater
1 free ethernet or USB port

Windows
Windows 10 or greater
1 free ethernet or USB port

iOS
iOS 8 or greater with Camera Connection Kit (CCK)*
CoreMIDI compatible app

Notes: mioXL- The MIDI interface redefined

mioXL is iConnectivity's flagship MIDI power-house, packed full with the very best technology and innovations. With mioXL it's never been easier to get huge amounts of MIDI gear connected and talking to each other. Harness the power of iConnectivity's advanced computer and network connectivity and experience why mioXL redefines what a flagship MIDI interface can and should do.

Connect all your MIDI devices (USB-MIDI, DIN-MIDI, RTP/Network-MIDI) and Mac, PC, and iOS computing devices to each other, and let this rugged, versatile interface put you in control of your MIDI devices and workflow.

On stage or in the studio, RTP/Network-MIDI capability means you are no longer constrained by cable length or limited USB ports. Stack multiple interfaces and computers on a network for ultimate scalability and flexibility.

With mioXL you're able to streamline and expand your MIDI setup, no matter how massive and demanding. Even though it's iConnectivity's most powerful MIDI interface, mioXL is still accessible to all users, allowing you to do whatever you want with MIDI faster, better, and in creative and exciting new ways.

What makes mioXL unique? The iConnectivity difference.

Next-gen Ethernet RTP MIDI adds massive capability and flexiibily

iConnectivity's next generation RTP/Network- MIDI capabilities, and what they'll do for you.

Ethernet connectivity means MIDI is on the network wherever you need it. Regular USB connectivity limits you to keeping your interface within 15ft of your computer. Ethernet connectivity gives you up to 330ft / 100m connection between you and your interface. Drop an interface in every room of your studio, or place an interface virtually anywhere in a venue.

RTP/Network-MIDI is not bound by some of the same restrictions as USB-MIDI.

Easy renaming of network ports - have them show up the way you want them to in your DAW.

Access to more than 22 ports per interface.

iConnectivity's unique network technology is as easy to use as USB! Enjoy your new-found MIDI power without extra headaches.

Use your 22 network MIDI ports anyway you want. Connect each of the 22 RTP-MIDI sessions to any combination of physical or virtual I/O ports. Almost any combination is possible.

Configuring mioXL:
Introducing a new version of iConnectivity's Auracle control software: taking the simplicity of workflow that the original Auracle introduced but now with the added deep configuration functionality that iConnectivity are known for. All the deep configuration options you asked for: MIDI merging, filtering, remapping, and deep routing are all there and super easy to use.

mioXL's display, rotary encoder and capacitive touch controls make navigating presets and monitoring MIDI traffic easy

Presets onboard:

Need to configure your MIDI setup in multiple ways? No problem!

New to mioXL : store and recall up to 32 presets directly on the interface, without even needing a computer!

Easily store and recall unique MIDI routing, filter and merging setups to preset scenes, and recall them all directly via the mioXL front panel.

mioXL's OLED display and encoder wheel gives you a crisp clear way of monitoring MIDI traffic, viewing, and selecting presets.

mioXL makes you the master of your MIDI domain. The MIDI interface: reinvented.

What's in the box:

1x mioXL
1x USB Cable.
1x Ethernet cable
1x mioXL 12V 36W Power Supply with interchangeable blades (NA, EU, UK and AU (Australia only)).

Device Specifications:

Width: 482.6 mm/19 in
Height (1U): 44.45 mm/1.75 in.

System Requirements

Macintosh
Mac OS X 10.11 or greater
1 free ethernet or USB port

Windows
Windows 10 or greater
1 free ethernet or USB port

iOS
iOS 8 or greater with Camera Connection Kit (CCK)*
CoreMIDI compatible app

Notes: At 84hp wide the NiftyCASE isn't super tiny or super huge, in fact, it's just right for all of the cardboard boxes bought to ship it to you in. Aside from the 84hp width NiftyCASE features ample +12v -12v and +5v power for your modules. It will also take Din MIDI from any DIN MIDI device and USB MIDI from your computer and turn it into eurorack compatible CV, gate, mod, and clock.

MIDI to CV, gate, clock, and mod

It's all built into the case. Make your instrument and don't waste precious hp (space for modules) on power and MIDI tools. you can plug NiftyCASE into your computer via USB or 5pin MIDI DIN device and send it MIDI. It will convert it into CV, gate, mod, and clock. Sequence with your DAW, jam with your controllers, or do something wacky, NiftyCASE has got you covered.

Power

Built-in power saves space for more of your modules, and keeps things good and easy.

As is, you can plug up to 10 modules into NiftyCASE's 10 gang flying bus that provides a peak 1500mA of +12v, 500mA -12v, and 500mA +5v, covering all industry standard power requirements

Specs:
Useable case area = 84hp
Internal depth = 55mm
Weight = 1.8kg
6.8cm x 44.6cm x 18.6cm
Range of cv out 1 = 0-10V
Range of cv out 2 = 0-10V
Voltage output gate 1 - off =0 on =5(off = 0 on = 4.65)
Voltage output gate 2 - off =0 on =5(off = 0 on = 4.65)
Voltage output mod = 1-10V
Voltage output clock - off =0 on =5
Power output for modules
+12V - 1500mA peak output**
-12V - 500mA peak output**
+5V - 500mA peak output**
1/4" ts mono output on rear
MIDI in via USB and 5 pin Din
MIDI thru via 5 Pin Din and USB

Included in the box:

NiftyCASE
NiftyCASE switching power supply with blades for NA, EU, UK, and AU

* Please note that the right and left sides of NiftyCASE fit very flush. It is recommended to favour a module with a pcb 1mm or more narrower than it's front panel for use on the left and right sides of the case (this amount or more of tolerance is fairly common on many modules).

** The NiftyCASE power supply is designed only to power modules that are being used in the NiftyCASE. Modifying the case or using it otherwise to power external cases & external modules is not advised.

Notes: Switched mults come to Intellijel's space-saving 1U format, offering six jacks and two busses, routing signals between the two or muting them using three-position switches.

Supplier's Notes:
The Mult 1U takes one audio or CV signal input, and (mult)iplies to up to four outputs. Because the Mult is passive, it requires no power to operate. Multiply anything by four, twice.

A signal multiplier accepts an input signal and routes it to multiple outputs simultaneously. For example, you might want a sequencer's GATE to trigger two different envelopes - one to control volume and one to control filter frequency. In order to accomplish this, you need a signal multiplier.

In addition, each Switched Mult 1U features a pair of 3-pin Link connectors on the rear panel. These let you connect other 3-pin Link devices, such as an XY I/O 1U module, or even additional Switched Mult 1U modules (handy for distributing mults across the width of your case).

Width: 14HP
Depth: 18mm
Power: n/a (passive)

Notes: Connect your USB compatible gear with Audio Optimized UDG Ultimate Audio cables.

This USB 2.0 cable with a streamlined design helps DJ's and Producers maximize their performance and is ideal for home and professional use where impeccable audio is a must.

UDG Ultimate Audio Cables are designed to interconnect devices with USB interfaces. It is ideal for connecting an audio interface, USB microphone, instrument or most computer peripherals to a PC.

The UDG Ultimate Audio Cables deliver professional performance made with superior flexible PVC cable construction, UDG branding on cable ends and Velcro cable strap validates they're official. For devices with an older USB version, this cable is backward compatible so you can still make the connection.

Specifications:

Color: White
Material: PVC + Metal
Protection: Constructed with corrosion-resistant, gold-plated connectors for optimal signal
Two ferrite chokes: help eliminate noise in both directions
High-quality multi-shielded PVC USB cable

Extras
Includes: UDG Velcro strap for easy storage
High-speed Audio Optimized USB 2.0 A-Male to B-Male cable
Ergonomic UDG Design
Various colors makes them easy to identify
Fits: Connects mic, keyboards, and speed-critical devices, such as audio interfaces and external hard drives to your computer

Notes: Connect your USB compatible gear with Audio Optimized UDG Ultimate Audio cables.

This USB 2.0 cable with a streamlined design helps DJ's and Producers maximize their performance and is ideal for home and professional use where impeccable audio is a must.

UDG Ultimate Audio Cables are designed to interconnect devices with USB interfaces. It is ideal for connecting an audio interface, USB microphone, instrument or most computer peripherals to a PC.

The UDG Ultimate Audio Cables deliver professional performance made with superior flexible PVC cable construction, UDG branding on cable ends and Velcro cable strap validates they're official. For devices with an older USB version, this cable is backward compatible so you can still make the connection.

Specifications:

Colour: White
Material: PVC + Metal
Protection: Constructed with corrosion-resistant, gold-plated connectors for optimal signal
Two ferrite chokes: help eliminate noise in both directions
High-quality multi-shielded PVC USB cable

Extras

Includes UDG Velcro strap for easy storage
High-speed Audio Optimized USB 2.0 A-Male to B-Male cable
Ergonomic UDG Design
Various colors makes them easy to identify
Fits: Connects mic, keyboards, and speed-critical devices, such as audio interfaces and external hard drives to your computer

Notes: Connect your USB compatible gear with Audio Optimized UDG Ultimate Audio cables.

This USB 2.0 cable with a streamlined design helps DJ's and Producers maximize their performance and is ideal for home and professional use where impeccable audio is a must.

UDG Ultimate Audio Cables are designed to interconnect devices with USB interfaces. It is ideal for connecting an audio interface, USB microphone, instrument or most computer peripherals to a PC.

The UDG Ultimate Audio Cables deliver professional performance made with superior flexible PVC cable construction, UDG branding on cable ends and Velcro cable strap validates they're official. For devices with an older USB version, this cable is backward compatible so you can still make the connection.

SPECIFICATIONS:

Colour: Black
Material: PVC + Metal
Protection: Constructed with corrosion-resistant, gold-plated connectors for optimal signal
Two ferrite chokes: help eliminate noise in both directions
High-quality multi-shielded PVC USB cable

Extras:
Includes UDG Velcro strap for easy storage
High-speed Audio Optimized USB 2.0 A-Male to B-Male cable
Ergonomic UDG Design
Various colors makes them easy to identify
Fits: Connects mic, keyboards, and speed-critical devices, such as audio interfaces and external hard drives to your computer

Notes: Connect your USB compatible gear with Audio Optimized UDG Ultimate Audio cables.

This USB 2.0 cable with a streamlined design helps DJ's and Producers maximize their performance and is ideal for home and professional use where impeccable audio is a must.

UDG Ultimate Audio Cables are designed to interconnect devices with USB interfaces. It is ideal for connecting an audio interface, USB microphone, instrument or most computer peripherals to a PC.

The UDG Ultimate Audio Cables deliver professional performance made with superior flexible PVC cable construction, UDG branding on cable ends and Velcro cable strap validates they're official. For devices with an older USB version, this cable is backward compatible so you can still make the connection.

SPECIFICATIONS:

Colour: Blue
Material: PVC + Metal
Protection: Constructed with corrosion-resistant, gold-plated connectors for optimal signal
Two ferrite chokes: help eliminate noise in both directions
High-quality multi-shielded PVC USB cable

Extras:
Includes UDG Velcro strap for easy storage
High-speed Audio Optimized USB 2.0 A-Male to B-Male cable
Ergonomic UDG Design
Various colors makes them easy to identify
Fits: Connects mic, keyboards, and speed-critical devices, such as audio interfaces and external hard drives to your computer

Notes: Connect your USB compatible gear with Audio Optimized UDG Ultimate Audio cables.

This USB 2.0 cable with a streamlined design helps DJ's and Producers maximize their performance and is ideal for home and professional use where impeccable audio is a must.

UDG Ultimate Audio Cables are designed to interconnect devices with USB interfaces. It is ideal for connecting an audio interface, USB microphone, instrument or most computer peripherals to a PC.

The UDG Ultimate Audio Cables deliver professional performance made with superior flexible PVC cable construction, UDG branding on cable ends and Velcro cable strap validates they're official. For devices with an older USB version, this cable is backward compatible so you can still make the connection.

Specifications:

Colour: Green
Material: PVC + Metal
Protection: Constructed with corrosion-resistant, gold-plated connectors for optimal signal
Two ferrite chokes: help eliminate noise in both directions
High-quality multi-shielded PVC USB cable

Extras:

Includes UDG Velcro strap for easy storage
High-speed Audio Optimized USB 2.0 A-Male to B-Male cable
Ergonomic UDG Design
Various colors makes them easy to identify
Fits: Connects mic, keyboards, and speed-critical devices, such as audio interfaces and external hard drives to your computer